Advertisement
Quick Links
INSTALLATION INSTRUCTIONS FOR CLEAN FACE PANEL KITS FOR USE WITH
KIT CONTENTS:
1 ea. Top Radiant Panel
1 ea. Bottom Radiant Panel
1 ea. Lennox Nameplate
1 ea. Instruction Sheet
Top Radiant Panel
Bottom Radiant Panel
GENERAL INFORMATION
These clean face panel kits may be used with Merit
Elite ® series gas fireplaces listed in Table 1.
INSTALLATION INSTRUCTIONS
Note: Do not operate fireplace without the eyebrow installed in its normal
position. See Figure 1 for models with louvers or Figure 2 for
models with clean face panel.
Step 1. G rasp the existing eyebrow and pull it forward away from the
fireplace (it is held in place by spring tension). See Figure 1.
Step 2. S lightly lift and pull the existing top louver assembly away from
the fireplace.
Step 3. S lide the existing eyebrow into the slots on the lower edge of the
top radiant replacement panel.
Step 4. Hang the top radiant panel/eyebrow assembly in the opening
previously occupied by the top louver assembly. See Figure 2.
Step 5. Open the bottom louver assembly by pushing in simultaneously
the left and right sides of the louver assembly (the assembly is
hinged at the bottom).
Step 6. M erit Series Units - Remove the assembly from the fireplace by
removing the hinge screw and spacer on each end of it.
Merit Plus and Elite Series Units - Remove the assembly from the
fireplace by sliding the hinge pin, located at the door's left side,
to the right until it disengages from the left corner post hole. Pull
the door diagonally to the left, away from the fireplace.
Step 7. Snap the replacement Lennox nameplate logo into the 2 holes
provided in the replacement panel.
Step 8. Merit Series Units - Install the replacement bottom radiant panel
using the existing hinge screws and spacers.
Merit Plus and Elite Series Units - Install the replacement bottom
radiant panel by inserting the right side locating pin into the right
cabinet corner post and then the left side spring-loaded pin into
the left cabinet corner post.
Lennox Hearth Products reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and the discontinuance of colors, styles and products.
Consult your local distributor for fireplace code information.
Printed in U.S.A. © 2001 by Lennox Hearth Products
P/N 504,223M REV. F 03/2008
MERIT
™,
MERIT PLUS
TOOLS REQUIRED:
None
CAUTION
INSTALL ONLY WHEN THE
FIREPLACE IS OFF AND COLD!
™
, Merit Plus
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
P/N 504,223M
REV. F 03/2008
™
OR ELITE
®
SERIES GAS FIREPLACES
CAT. NO.
MODEL
88L36
RAD35C-2
88L37
RAD40C-2
88L38
RAD45C-2
88L35
RAD24C-2
98L12
RAD33C
™
or
26M47
RAD33MC
H7019
RAD22C-2
Table 1 - Painted Panel Kits
Hood must be installed as shown.
Figure 1 - Louvered Face
Hood must be installed as shown.
Figure 2 - Clean Face
LENNOX HEARTH PRODUCTS
KITS AND ACCESSORIES
CLEAN FACE PANEL KITS
(PAINTED FINISH)
WHERE USED
EDV3530, ED3530 front-open, MPD3530,
MPD35ST/PF, MPB35ST
EDV4035, ED4035-2, MPD4035 front open,
EDVST, EDST-2, EDVPF, EDPF-2, EDVCR,
EDCR-2, EDVCL, EDCL-2, EBST-2, EBVPF,
EBPF-2, EBVCR, EBCR-2, EBVCL, EBCL-2
multi-open (long panel)
EDV4540, ED4540-2, MPD4540 front-open
EDVPF, EDPF-2, EDVCR, EDCR-2, EDVCL,
EDCL-2, EBVPF, EBPF-2, EBVCR, EBCR-2,
EBVCL, EBCL-2 multi-open (short panel)
MDR3328, MDT3328, MPDT3328,
MPDR3328
MPD3530, MPD35ST
MPD35PF
Top of Appliance
Louver Assembly
Top of Door Frame
Top of Appliance
Top Radiant Panel
Top of Door Frame
Lennox Hearth Products
1110 West Taft Avenue • Orange, CA 92865
Advertisement
