Summary of Contents for Lennox Hearth Products CR-3835R
Page 1
36" Wood Burning Fireplaces P/N 850,048M REV. N/C 01/2007 MODELS CR-3835R This installation manual will enable you to obtain a safe, efficient and dependable installation of your fireplace system. Please read and under- stand these instructions before beginning your installation.
The most important areas of concern dealing with the installation of factory-built fireplaces are clearances to combustible materials, proper as- sembly of component parts, height of the chim- ney system, the proper use of accessories sup- plied by the manufacturer and the techniques employed in using finishing materials applied to the wall surrounding the fireplace, hearth exten- sions and wall shields.
Insulate Joists Same As Ceiling Draft Stops Firestop CTDT Termination Note: Non- Combustible Chase Flashing Must Be Used To Cover Chase Opening Level Solid Continuous Surface Insulation (Thermal Barrier) Figure 2 WARNING: IF INSULATION IS USED, THE FIREPLACE MUST NOT BE PLACED DI- RECTLY AGAINST IT.
ASSEMBLY STEPS Note: The following steps represent the normal sequence of installation. Each installation is unique, however, and might require a different sequence. 1. Position firebox prior to framing or into prepared framing. 2. Install the chimney system. 3. Connect house wiring to the fireplace for later attachment of optional blower.
IMPORTANT: UNDER NO CIRCUMSTANCES CAN THE FIREPLACE TOP SPACERS ( FIGURE 6 ) BE REMOVED OR MODIFIED, NOR MAY YOU NOTCH THE HEADER TO FIT AROUND OR BE INSTALLED LOWER THAN THE SPAC- ERS. THE HEADER MAY BE IN DIRECT CON- TACT WITH THE TOP SPACERS BUT MAY NOT BE SUPPORTED BY THEM.
FRAMING SPECIFICATIONS Header Framing Without False Header Figure 12 Back Wall of Chase/Encloslure Including Finishing Materials if any Rough Framing Face (Unfinished Outside Corner Shown) Figure 13 Framing Dimensions for Ceiling Flue Type FTF8 Vertical " " at 2" (419 mm) (419 mm) FTF10 Vertical 17"...
Step 6. Route the Class 0 air duct out the back wall or side wall, up through the ceiling or floor joists to an outside wall. The air duct should be located above snow level. Note: If the fireplace is installed against an inside wall, the Class 0 air duct may be ex- tended into a ventilated attic space at least 18"...
CHIMNEY 30 OFFSET THROUGH FLOOR OR CEILING It may be necessary to assemble the chimney at 30 when passing through the floor or ceiling area. Use the F8FS30-2 firestop spacer as shown in Figures 21 and 22 . Support the chimney at floor or ceiling penetration with a FTF8 stabi- lizer if distance of chimney below ceiling is 10' or more.
Page 10
Note: Do not apply excessive pressure to any subsequent chimney sections following the stabilizer when installing. Ensure each subse- quent chimney section is securely attached by testing as noted in Step 4. Step 6. Select the proper Security Chimneys roof flashing based on pitch of roof. Use chart below for selection: Roof Pitch FTF8...
Less Than 10' Figure 32 Using a FTF8/10-CT1 Chase Termination: Refer to specific installation instructions in- cluded with FTF8/10-CT1 chase terminations for clearance and installation details. Using a FTF8/10-CT2 Chase Termination: Refer to specific installation instructions in- cluded with FTF8/10-CT2 chase terminations for clearance and installation details.
The offset and return elbows may be attached together, or a section or sections of chimney may be used between, but do not exceed 20' in total length between elbows. If sections of pipe exceed 10' between elbows, a chimney stabi- lizer must be used at the midpoint ( Figure 34 ).
INSTALLING OFFSETS First, review the Offset Elevation Chart and Figure 38 for reference. Step 1. Determine the offset distance where chimney is to pass through the first ceiling- dimension “A.” To find this point on your ceil- ing, first determine the center point for a verti- cal chimney following the instructions for ver- tical installation.
Glass Doors If glass doors are to be installed on these fireplaces, refer to specific installation instruc- tions packed with the glass doors. Use only the doors that are listed for use with these fire- places. Use of other non-listed glass door on these fireplaces may constitute a potential fire hazard and is not recommended.
Page 19
Hearth Extension Dimensions 20" (508 mm) 38" (965 mm) 8" (203 mm) 20" (508 mm) 12" (305 mm) Figure 43 Methods of Determini ng Hearth Extension and Wall Shield Equivalents - To determine the thickness required for the alternate material when either the “k” value or “r” value is known, use either the k formula or r formula.
Fireplace Shaded Area “Safe Zone” 11 ⁷⁄₈” 8" 15 ⁷⁄₈” Min. Distance To 8" Protected Side Wall Min. Distance To 12" Unprotected Side Wall Figure 46 Model Part Number Weight CR-3835R P/N 015014 210 lbs. CR-3835L P/N 015013 210 lbs.
INSTALLATION COMPONENTS The following items are available for use in the installation of this appliance. 63L10 FTF8-12 63L13 FTF8-18 63L14 FTF8-36 63L15 FTF8-48 63L16 FTF10-12 63L17 FTF10-18 Chimney Section 63L18 FTF10-36 62L92 FTF8-18C 62L93 FTF8-36C Canadian 62L94 FTF10-18C Outside Chimney 62L95 FTF10-36C 63L38...