Summary of Contents for Lennox Hearth Products CST-38
Page 1
SERIES 36" Wood Burning Fireplaces P/N 850,049M REV. N/C 01/2007 MODELS CST-38 CPF-38 This installation manual will enable you to obtain a safe, efficient and dependable installation of your fireplace system. Please read and under- stand these instructions before beginning your installation.
TABLE OF CONTENTS 2. Always check your local building codes. The The manufacturer is not responsible for any installation must comply with all local, re- smoking or related problems that may result from the lack of adequate combustion air. It is gional, state and national codes and regula- Safety Rules ........
8" (203 mm) for both the CPF-38 THOSE DESCRIBED IN THIS MANUAL CST-38 and CPF-38 to properly position the and CST-38 fireplaces ( see Figure 60 and MAY CREATE A FIRE HAZARD AND VOID fire. An outside combustion air kit is available Figure 61 ).
Must Be circulation, aesthetics, chimney obstructions Used To Cover and clearance to side wall(s). With proper pre- Chase Model CST-38 Security's planning, a slight adjustment of a few inches Opening and CPF-38 FTF8 can save considerable time and expense later during construction and assembly.
1. Estimate the total weight of the fireplace system including chimney and surround ma- Floor Floor terials such as brick, stone, etc., to be in- CPF-38 CST-38 stalled. Shipping weights for the fireplace may 5-5/8" 11-3/8" Figure 6 be found on page 18.
Page 6
If the appliance is to be elevated above floor level, a solid continuous platform must be constructed. Platform The header may rest on the top metal spacers, but must not be notched to fit around them. Consult all local codes. Metal Free Air Space.
FRAMING WALL VARIATIONS CPF - Wall Types As many as six (6) different framed wall con- figurations can be constructed to enclose the CST and CPF fireplaces. The following illustra- tions depict these variations of wall enclosures. Several of these designs may incorporate book shelves, wood storage boxes, etc.
Step 4. The fireplace should be secured to side Step 6. Connect the 4" (102 mm) Class 0 or A minimum 2" (51 mm) air space must be framing members using nailing tabs. Use 8d Class 1 air duct to the collar (just mounted) with reserved for all combustible materials extend- two (2) No.
Page 11
Note: If there is a room above ceiling level, The FTF8 chimney system is a two-piece chim- firestop spacer must be installed on the bottom ney, which snaps together from the fireplace side of the ceiling. If an attic is above ceiling up.
Page 12
Step 6. Select proper Security Chimneys roof Step 8. The standard Security Chimneys FTF8 flashing based on pitch of roof. Use chart below roof flashing assembly includes a storm col- for selection: lar. Slide storm collar over outer chimney, align with top surface of flashing, insert storm tab in slot, pull tight and bend tab back over Roof Pitch FTF8...
2. Determine the number of chimney compo- Less than nents required, except chimney sections. This 10' (3m) would include firestop spacers, stabilizers, roof flashing, etc. 2' (610mm) Min. 3' (914mm) 3. The effective heights of the components are: Min. 10' (3m) 3' (914mm) CST/CPF Fireplace = 48"...
FTF8 VERTICAL ELEVATION CHART Height Of Number Of FTF8 Height Of Height Of Number Of FTF8 Height Of Chimney Only Chimney Lengths Chimney Only Chimney Only Chimney Lengths Chimney Only Inches Feet/Inches 12" 18" 36" 48" Inches Feet/Inches 12" 18" 36" 48" 0 11 0.28 6401...
RETURN ELBOW ASSEMBLY The offset and return elbows may be attached Return elbow support straps must be securely together, or a section or sections of chimney attached under tension (in shear) to structural may be used between, but do not exceed 20' framing members above.
If you’re installing a gas line, connect it before CST-38 fireplace and two (2) glass door as- the fireplace is framed and enclosed in the semblies plus one (1) end panel for the CPF- finished wall.
Header off device and complying with the standard for For the CST-38 a wall shield is required where Decorative Gas Appliances for installation in a continuous perpendicular side wall is within vented fireplaces, ANSI Z21.60. Install in ac- 18"...
If “C” Style Door Is Used. Using 1/2” of mortar to set the brick, “R” for the mortar is calculated as follows: mortar Model CST-38 “R” = 0.20 x 1/2" = .10 Figure 57 5 ⁵⁄₈" Next, a 3/4" marble slab set in 1/2" mortar cov- (143 mm) Max.
Side Wall Model CPF-38 Figure 61 ACCESSORY PARTS AND COMPONENTS LIST FOR MODELS CST-38 AND CPF-38 The accessory parts and components shown on pages 21 and 22 are to be used only with your CST-38 and CPF-38 fireplace systems.