Starting Operation - Bosch ANGLE EXACT ION 18 V-LI Original Instruction

OBJ_BUCH-1521-004.book Page 19 Friday, December 6, 2013 8:19 AM
steps to the desired position and retighten the sleeve nut
again with the open-end spanner 20 by the spanner flats 5.
Hold the angled head flange with the open-end spanner 21
to prevent turning.
Adjusting and Removing the Angled Drive Head
(see figure E)
ANGLE EXACT ION
Applies for the fol-
lowing types: 30-300 | 40-220 | 50-210 | 60-120
The angled drive head 3 with tool bit holder 2 can be continu-
ously adjusted around 360°.
– Loosen the lock nut 22 by inserting an appropriate tool in-
to an opening of the lock nut and turning the lock nut in the
direction of the arrow a (left thread).
– Fix the angled drive head 3 in this position by turning the
lock nut 22 in the direction of the arrow c against the an-
gled drive head. Tighten the lock nut 22 with a tightening
torque of max. 50 Nm again.
– Turn the angled drive head 3 in arrow direction b until the
desired work angle is reached, but not more than once by
360°.
The angled drive head 3 can also be removed completely,
e. g. when it is required to replace the marking ring 17 by one
with another colour or to adjust the worklight. Adjust the
worklight to the desired position first (see "Adjusting the
Worklight", page 18) before adjusting the angled drive head.
– Loosen the lock nut 22 by inserting an appropriate tool in-
to an opening of the lock nut and turning the lock nut in the
direction of the arrow a (left thread).
Unscrew the angled drive head 3 in arrow direction b until
it can be removed.
Unscrew the lock nut 22 from the motor housing 23 in ar-
row direction a.
Now, the marking ring can be exchanged or the worklight can
be adjusted.
– Turn the lock nut 22 in arrow direction c onto the motor
housing 23 and screw on the angled screw head again
turning in arrow direction b.
– Lock the angle nutrunner head by screwing the lock nut 22
in arrow direction c.
– Retighten lock nut 22 again with a tightening torque of ap-
prox. 50 Nm.
Configuring the Power Tool
With the BOSCH EXACT Configurator software, different pow-
er tool settings (e. g., speed, driving stages, repeat protec-
tion) can be configured. For this, the power tool must be con-
nected to a PC via the USB data port.
Note: Observe all safety warnings and instructions in the soft-
ware instruction manual.
Changing Application Tools on the Screw Head
with External Square Drive (see figure F)
Inserting
– Press in the pin on the drive square of the tool holder 2,
e. g. using a small screwdriver, and slide the tool bit 1 over
the drive square. Pay attention that the pin engages in the
recess of the tool bit.
Bosch Power Tools
Removing
– Press in the pin in the recess of the tool bit 1 and pull the
tool bit out of the tool holder 2.
Changing Application Tools on the Screw Head
with Internal Hexagon (see figure G)
Inserting
– Insert the tool bit 1 into the internal hex socket of the tool
holder 2 until it can be felt to engage.
Removing
– Pull the tool bit 1 off of the tool holder 2 with the aid of pli-
ers, if necessary.
Changing Application Tools on the Head with
Quick-change Chuck (see figure H)
Inserting
Use only insertion tools with fitting end pieces
(1/4" hexagonal).
– Pull the sleeve of quick-change chuck 24 to the front and
hold.
– Insert tool bit 1 into tool holder 2 and release the quick-
change chuck.
Removing
– Pull the sleeve of quick-change chuck 24 to the front and
hold.
– Remove tool bit 1 from tool holder 2 and release the quick-
change chuck.
Operation
 Before any work on the power tool, remove the battery.

Starting Operation

When starting the power tool, you should first select the di-
rection of rotation with the rotational direction switch 11
since the power tool starts only when the rotational direction
switch 11 is not in the middle position (switch-on lock).
Reversing the rotational direction (see figure I)
– Right rotation: For driving in screws, push the rotational
direction switch 11 left to the stop.
– Left Rotation: For loosening or unscrewing screws, push
the rotational direction switch 11 right to the stop.
Switching On the Worklight
The work area illumination 13 makes possible the lighting of
the screwing position for unfavorable light conditions. The
work area illumination 13 is switched on by lightly pressing
the on/off switch 10. When the on/off switch is firmly
pressed, the power tool is switched on and the work area illu-
mination continues to light.
 Do not look directly into the work area illumination –
your sight can be temporarily degraded!
English | 19
1 609 92A 0CM | (6.12.13)