Download Print this page

General Safety Information; Save These Instructions - Lasko 5521 Operating Manual

Remote control ceramic tower heater with digital display

Advertisement

GENERAL SAFETY INFORMATION

When using electrical appliances, basic precautions should always be followed to reduce the
risk of fire, electrical shock and injury to persons, including the following:
Read all instructions before using this Heater.
1.
DO NOT PLUG HEATER INTO ANY OTHER CORD CONNECTED DEVICE, SUCH AS A POWER STRIP, SURGE PROTECTOR, MUL-
TIPLE OUTLET ADAPTER, CORD REEL OR OUTLET-TYPE AIR FRESHENER. THE USE OF SUCH DEVICES MAY CREATE A FIRE
HAZARD. PLUG UNIT DIRECTLY INTO A 120V WALL OUTLET ONLY.
2.
AVOID THE USE OF EXTENSION CORDS BECAUSE THE EXTENSION CORD MAY OVERHEAT AND CAUSE A RISK OF FIRE.
HOWEVER, IF YOU HAVE TO USE AN EXTENSION CORD, MINIMIZE THE RISK OF OVERHEATING BY USING THE SHORTEST
CORD POSSIBLE AND BY ENSURING THAT IT IS UL LISTED. THE CORD SHALL BE A 3-WIRE, GROUNDING TYPE, WITH NO. 14
AWG MINIMUM SIZE AND RATED NOT LESS THAN 1875 WATTS (15A). NEVER USE A SINGLE EXTENSION CORD TO OPERATE
MORE THAN ONE HEATER. NEVER USE A CORD REEL.
WARNING:
Faulty wall outlet connections may cause the wall outlet to overheat. Be sure that heater plug fits tightly into outlet be-
fore each use. During use, check to make certain the Heater plug is not overheating. If necessary have a qualified electrician check
and/or replace the wall outlet.
3.
Use this Heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electrical shock,
or injury to persons.
4.
Make certain that the room is equipped with a working smoke detector.
5.
Make certain that the power source conforms to the electrical requirements of the Heater.
6.
Extreme caution is necessary when any Heater is used by or near children or invalids and whenever the Heater is left
operating unattended.
7.
This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a
polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician.
Do not attempt to defeat this safety feature.
8.
Do not operate any Heater with a damaged cord or plug or after the Heater malfunctions, or has been dropped or damaged in any manner.
Please contact Customer Service at 800-233-0268 Monday through Friday from 8am to 5pm EST for assistance.
9.
To disconnect Heater, turn the Heater OFF then remove the plug from the outlet.
10. Always unplug Heater when not in use. Unplug power cord before servicing or moving the Heater.
11. Do not insert or allow fingers or foreign objects to enter any ventilation or exhaust opening as it may cause an electric shock, fire, or
damage the Heater. Do not block or tamper with the Heater in any manner while it is in operation.
DO NOT DEPEND ON THE ON/OFF SWITCH AS THE SOLE MEANS OF DISCONNECTING POWER WHEN
SERVICING OR MOVING THE HEATER. ALWAYS UNPLUG THE POWER CORD. ALWAYS TURN OFF AND
UNPLUG HEATER BEFORE LEAVING THE AREA. NEVER LEAVE CHILDREN UNATTENDED WHEN THE
HEATER IS ON OR PLUGGED IN.
12. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not place on soft surfaces, like a bed, where openings
may become blocked.
13. Always place the Heater on a stable, flat, level surface when operating, to avoid the chance of the Heater overturning. Locate the Power
Cord so the Heater or other objects are not resting on it. DO NOT run Power Cord under carpeting. DO NOT cover Power Cord with throw
rugs, runners, or the like. Arrange Power Cord away from room traffic and where it will not be tripped over.
14. This Heater is HOT when in use. To avoid burns, do not let bare skin touch hot surfaces. Always use handle when moving this Heater.
Keep combustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet (0.9 m) from the front of the
Heater and keep them at least 1 foot (0.3 m) from the sides and rear.
15. A Heater has hot and arcing or sparking parts inside. DO NOT use the Heater in areas where gasoline, paint, or flammable liquids are
used or stored. DO NOT use Heater in locations where flammable or explosive chemicals are stored, or in wet atmospheres. This Heater
is intended for general use ONLY.
16. This Heater is not intended for use in wet or damp locations. This Heater is not intended for use in bathrooms, laundry areas and similar
indoor locations. NEVER locate a Heater where it may fall into a bathtub or other water container.
17. DO NOT use Heater outdoors.
18. Remote controls for other appliances or electronic equipment can sometimes interfere with the operation of this Heater. If this occurs, move
the Heater to another location.
19. Keep Heater remote control unit away from chairs and your bed where it may be sat or laid upon and inadvertently turn on the Heater.
20. This Heater is not suitable for use in agricultural facilities including areas where livestock, poultry or other animals are confined. Please refer
to National Electric Code (NEC) Article 547-7 (2002), or applicable state or local codes or standards relating to electrical requirements for
Agricultural Buildings. THIS HEATER DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 547-7 (2002).
21. This Heater is not suitable for use in hazardous locations. Please refer to National Electric Code (NEC) Article 500 or applicable state or
local codes or standards relating to electrical requirements for Hazardous locations. THIS HEATER DOES NOT MEET THE
REQUIREMENTS OF NEC ARTICLE 500 (2002).
WARNING: REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK – DO NOT USE THIS HEATER WITH ANY SOLID STATE SPEED
CONTROL DEVICES.

SAVE THESE INSTRUCTIONS

New 2/07
2
FUNCIONAMIENTO
(Figuras 1 a 3)
1. Cuidadosamente retire el Calefactor de la bolsa y de la caja.
2. Coloque el Calefactor sobre una superficie firme y plana.
ADVERTENCIA:
Los tacos de plástico o hule, tales como las
patas de esta unidad, pueden pegarse a la superficie de los muebles
y/o a los pisos de madera. La unidad podría dejar un residuo capaz
de oscurecer, manchar o dejar marcas permanentes en el acabado
de ciertas superficies de muebles, incluyendo superficies de madera
y/o pisos de madera.
3. Conecte el cable eléctrico a un tomacorriente eléctrico de 120V~.
Asegúrese que el enchufe encaje firmemente en el tomacorriente.
4. Cuando el Calefactor se conecte por primera vez, se oirá un "bip"
permanecerá encendida hasta que el Calefactor sea desconectado
del tomacorriente eléctrico.
5. ENCIENDA el Calefactor oprimiendo el Botón de Encendido ( ).
6. Cuando se lo encienda por primera vez, el Calefactor
mostrará la temperatura actual de la habitación en grados
Fahrenheit. Oprima los botones ( ) y ( ) al mismo tiempo para
cambiar la pantalla a grados Celsius. Oprima los dos botones al
mismo tiempo nuevamente para cambiar la pantalla y volver a
grados Fahrenheit.
7. Al encender el Calefactor, la unidad estará en calor ALTO ( )
(1500 vatios) y mostrará la temperatura actual de la habitación
(Figura 2)
8. Oprima el botón ( ) para calor BAJO ( ). (900 vatios)
9. Para APAGAR el Calefactor, presione el Botón de Encendido
( ) y desconecte el Calefactor del tomacorriente eléctrico.
Pantalla al ser encendido por primera vez
Figura 1
OSCILACIÓN:
Oprimir el Botón de Oscilación ( ) le permitirá al Calefactor oscilar
hacia atrás y hacia delante. Para detener la oscilación, vuelva a
oprimir el Botón de Oscilación ( ). Cuando el calefactor esté
en control automático de temperatura, la función de oscilación se
detendrá cuando se alcance la temperatura fijada y reiniciará cuando
el calefactor vuelva a encenderse.
FUNCIÓN DE TEMPORIZADOR:
La función de temporizador puede ser activada cuando la pantalla
del Calefactor está en cualquier función o velocidad. (Figura 2) Esta
función le permite fijar la cantidad de tiempo que el Calefactor estará
funcionando antes de apagarse automáticamente, de 1 hora a 8 horas.
Presionar el Botón de Temporizador ( ) aumentará la cantidad de
tiempo en 1 hora cada vez que dicho botón sea oprimido. Después
que la pantalla refleje 8 horas, si presiona el Botón de Temporizador
( ) una vez más, se reiniciará el Calefactor para función continua.
El Calefactor se apagará cuando el tiempo fijado haya transcurrido.
La unidad puede ser encendida nuevamente presionando el Botón
de Encendido ( ).
5521ES
New 2/07
MODELO 5521
Función de Temporizador
Función de Temporizador
en Calor Bajo
automático de temperatura
Figura 2
CONTROL AUTOMÁTICO DE TEMPERATURA:
Oprimir el botón ( ) o el botón ( ) le permite a usted fijar la
temperatura deseada del Calefactor. (Figura 3)
1. Cuando el botón ( ) o el botón ( ) esté presionado, la pantalla
exhibirá la temperatura fijada y el símbolo ( ) aparecerá.
2. Oprima el botón ( ) para aumentar la temperatura fijada
deseada o presione el botón ( ) para reducir la temperatura
fijada deseada.
3. Cuando la temperatura del aire alcance los 2 grados por encima
de la temperatura fijada, el Calefactor se apagará.
4. Cuando la temperatura del aire alcance un 1grados por debajo
de la temperatura fijada, el Calefactor se encenderá.
5. Esta función se cancelará si el botón ( ) es oprimido y el
Calefactor ahora estará en calor Alto ( ).
NOTA: Es normal que el Calefactor alterne entre ENCENDIDO y
APAGADO para mantener la temperatura FIJADA.
La pantalla refleja calor Alto y la función de Control
Automático de Temperatura
Figura 3
CONTROL REMOTO:
Todas las funciones realizadas con el Control Remoto operan del
mismo modo que los controles manuales, excepto que usted no puede
cambiar de grados F a grados C. (Figura 4)
1. Instale las dos baterías "AAA" provistas.
2. No mezcla baterías viejas y nuevas. No mezcle baterías alcalinas,
estándar (carbono-zinc) o recargables (níquel-cadmio).
3. NO SE DESHÁGA DE BATERÍAS EN EL FUEGO. BATERÍAS
PUEDEN ESTALLAR O PUEDEN SALIRSE.
Vista
Frontal
Figura 4
Si usted pierde su mando a distancia, por favor Cliente de llamada
Serive para ordenar un reaplacement en 1-800 -233-0268, de lunes
a viernes, entre las 8 a.m. y las 5 p.m. (Horario Estándar del Este de
los Estados Unidos).
7
en Calor Alto y control
Vista
Posterior
+
+
5521ES

Hide quick links:

Advertisement

loading