Advertisement
OPERATION
The Heater may be operated by the manual controls located on
the Heater (as shown in Figure 1 ) or by your remote control
(shown in Figure 2 ).
1. Place the Heater on a firm, level surface, after assembling per
this manual.
WARNING:
Plastic or rubber tabs, like the feet on this unit, may
stick to furniture surfaces and/or hardwood floors. The unit may leave
a residue that could darken, stain or leave permanent blemishes on
the finish of certain furniture surfaces, including wood surfaces, and/
or hardwood floors.
2. Plug the cord set into a 120 V~ electrical outlet. Be sure plug fits
tightly in outlet.
3. When the Heater is initially plugged in, there will be a 'beep' and
the power light will come on indicating that there is power to the
unit. The power light will remain lit until the Heater is unplugged
from the electrical outlet.
4. Turn the Heater ON by pressing the Power Button ( ).
5. When initially turned on, the Heater will display the current
room temperature in ° Fahrenheit. Press the ( ) and ( ) but-
tons at the same time to change the display to ° Celsius. Press
the same two buttons together again to change the display
back to ° Fahrenheit.
6. The display will reflect "Room Temp" along with the current tem-
perature. The unit will be in the HIGH heat. (1500 Watts)
7. Pressing the ( ) Button at this point will set the Heater into LOW
heat. (900 Watts)
8. To turn the Heater OFF, press the Power Button ( ) and unplug
the unit from the electrical outlet.
View of Control Panel
Figure 1
Rev. C 5/05
MODEL 5365
Oscillation Function:
The oscillation function will work in any mode. Pressing the Oscilla-
tion Button (
) will allow the Heater to oscillate back and forth. To
stop the oscillation, press the Oscillation Button (
Timer Function:
The timer function will work in any mode. The timer function allows
you to set the length of operation from 1 hour to 8 hours. Press-
ing the Timer Button ( ) will increase the length of operation by
1 hour each time the button is pressed. Pressing the Timer But-
ton ( ) once more after the display reflects 8 hours will reset the
Heater to continuously running. Once the timer has been set, the
timer will count down the hours in 1 hour increments, showing on
the display the remaining operating time. The Heater will turn itself
off when the set time has lapsed. The unit can be turned back on by
pressing the Power Button ( ).
THERMOSTAT INSTRUCTIONS
1. Pressing the ( ) or ( ) Button will prompt the Heater into High
heat and will allow the thermostat to be set at a desired tempera-
ture. The display will shows AUTO and the word "SET". The tem-
perature will be flashing.
2. To adjust SET temperature, press the ( ) to increase the desired
temperature and the ( ) to decrease the desired temperature.
3. When the air temperature reaches 3 degrees above the SET tem-
perature, the heater will shut off.
4. When the air temperature drops 1 degree below the SET tem-
perature, the unit will turn on.
Note:
It is normal for the Heater to cycle ON and OFF as it main-
tains the SET temperature.
REMOTE CONTROL
(Figure 2)
All the functions performed with the Remote Control work identi-
cally to the manual controls, except that you are unable to change
from °F to °C with the remote control.
1. Install the two "AAA" batteries supplied.
2. Do not mix old and new batteries. Do not mix alkaline, standard
(carbon-zinc) or rechargeable (nickel-cadmium) batteries.
Front View of
Rear View of
Remote Control
Remote Control
Figure 2
If you lose your remote control, please call Customer Service to
order a replacement at 1-800-233-0268, Monday through Friday,
between the hours of 8:00 a.m. and 5:00 p.m. EST.
4
ARMADO
(Figuras 1 a 6)
Para facilitar el armado, coloque el Calefactor de manera que la
parrilla frontal y el panel de control den hacia arriba. Retire
cuidadosamente el Calefactor de su bolsa y caja.
) once more.
(8) - M5 X 13mm
Tamaño Real De Tornillos
1. Coloque el Cable Eléctrico en la parte inferior del Calefactor.
Pase el Cable Eléctrico por el centro del Conjunto de
Soporte de Columna.
2. Una el Conjunto de Soporte de Columna a la Base del Motor
con (4) tornillos M5 X 13mm. Cerciórese de que la Llave que
está en la Base del Motor quede alineada con la Muesca de
Ubicación en el Conjunto de Soporte de Columna . (Figura 2)
Cable
Eléctrico
3. Arme la base enclavando las Protuberancias en los Orificios
para Protuberancias . (Figura 3)
+
+
Protuberancias
Llave
5365ES
Rev. C 5/05
MODELO 5365
4. Fije las mitades de la base con (2) tornillos M4 X 13 mm. Pase el
Cable Eléctrico por el gran orificio que se encuentra del Conjunto
de la Base . NOTA: El Canal Para Cable en la parte inferior de la
base debe estar hacia la parte posterior del Calefactor. (Figura 4)
Canal Para
(2) - M4 X 13mm
Conjunto de
la Base
Figura 1
5. Alinee el Conjunto de la Base con el Conjunto de Soporte de
Columna . Cerciórese de que la Muesca de Ubicación en el
Conjunto de Soporte de Columna quede alineada con la Llave
Base del
en el Conjunto de la Base (Figura 5) . Una el Conjunto de la
Motor
Base al Conjunto de Soporte de Columna con (4) tornillos M5
X 13 mm. Jale suavemente el Cable Eléctrico para que no quede
holgado, y colóquelo en el Canal Para Cable del Conjunto de
la Base . (Figura 6)
Llave
Conjunto de Soporte
de Columna
Figura 2
Llave
Conjunto de
la Base
Orificios
para
Protuberancias
Figura 3
9
Cable
Cable
Eléctrico
Cable
Eléctrico
Figura 4
Muesca de
Ubicación
Figura 5
Conjunto de
Soporte de
Columna
Cable Eléctrico
Canal Para
Cable
Figura 6
5365ES
Advertisement
