Advertisement
Quick Links
Advertisement
Related Manuals for Whirlpool AKR3000/IX
Summary of Contents for Whirlpool AKR3000/IX
- Page 1 INSTRUCTION MANUAL T- Box Hood AKR3000/IX AKR3070/IX AKR3060/IX...
- Page 2 Maximum suction 1000m Diameter of Exhaust Pipe 150mm Product Dimension (mm) L 900 x W 480 x H 510-985（AKR3000/IX） Product Dimension (mm) L 760 x W 480 x H 510-985（AKR3070/IX） Product Dimension (mm) L 600 x W 480 x H 510-985（AKR3060/IX）...
- Page 3 future reference. * This cooker hood designed to be used only in the Ducted Mode * Only a qualified and trained service technician can undertake the work of installation and servicing. * Check that the mains voltage corresponds to the one indicated on the rating plate fixed inside the hood.
- Page 4 overheated oil can burst into flame. * The hood should not be used by children or person not instructed on its correct usage. MAINTENANCE * Proper maintenance of the Range Hood will assure proper performance of the unit. * Disconnect the hood from the main supply before carrying out any maintenance work.
- Page 5 supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. * There shall be adequate ventilation of the room when the range hood is used at the same time as appliances burning gas or other fuels.
- Page 7 COMPONENTS Components 2/3pcs Grease filter 1pcs Hood body steel bolt Cross self-drill bolt Exhaust Exterior chimney Inner chimney Cross discal thread bolt Fixing frame Cross discal bolt-big head Flat rubber band Plastic distensible sleeve Documentations Instruction Manual Warranty Card INSTALLATION & USE Note 1: Carefully remove the protective film from chimney and front panel prior to final installation.
- Page 8 1. Drill the holes according to the distances indicated (Fig.2). 2. Fix the appliance to the wall and align it in horizontal position to the wall units. 3. When the appliance has been adjusted, fix the hood using the screws A. For the various installations use screws and screw anchors suited to the type of wall (e.g.
- Page 9 Fig.4 Fig.5 DUCT FIXING Caution: To reduce the risk of fire, recommend use aluminium ductwork. φ 1. Attach an adequate length of 150mm round duct into the recessed area of the air outlet adapter. 2. The duct has to be secured using two screws from two sides of the air outlet adapter.
- Page 10 Caution: To reduce the risk of fire, use metal ductwork only. 1. Decide where the ductwork will run between the hood and the outside. 2. A straight, short duct run will allow the hood to perform most efficiently. 3. Long duct runs, elbows, and transitions will reduce the performance of the hood.
- Page 11 OPERATION OF CONTROLS 1. Press ‘E’ to turn ON / OFF the lamp Normal Mode Operation 1. Press ‘B’ to turn ON at speed 1 / Adjust speed 2. Press ‘C’ to turn ON at low speed 3 / Adjust speed 3.
- Page 12 dry before refitting. 3. To install the grease filter, press the latch on the filter again. Make sure the filter is securely engaged after assembly. WARNING: Always switch off the electrical supply before carrying out any operation on the appliance. Only a qualified and trained service technician can undertake the work of blubs replacement and servicing.
- Page 13 Cleaning tips: * Hot water with soap or detergent is all that is usually needed. * Follow all cleaning by rinsing with clear water. Wipe dry with a clean, soft cloth to avoid water marks. * For discolorations or deposits that persist, use a non-scratching household cleanser or stainless steel polishing powder with a little water and a soft cloth.
- Page 14 TROUBLE SHOOTING In case if the Cooker Hood is not working or working improperly, before calling the after sales service, switch off the appliance, unplug the power supply and refer to the guide below to determine the problem S.No. Status Reasons Solutions Lamp doesn’t...