Utilitech UTTNDIW7D Operating Instructions

MODEL #UTTNDIW7D
IN-WALL
DIGITAL TIMER
Call customer service at 1-866-994-4148,
8 a.m. - 6 p.m., EST, Monday - Thursday,
8 a.m. - 5 p.m., EST, Friday.
IMPORTANT PRODUCT INFO
• Single Pole: Timer will control devices from one location.
Do not use in a 3-Way application where multiple switches
control the same device.
• Neutral Wire: This is a wire that must be available as part
of the wiring in the building. Timer will not function properly
if a neutral wire is not available in the wall box (see Step 3
under "Installation").
• Direct Wire: This timer is only intended to be permanently
installed into an electrical wall box.
• Tool Required: One (1) standard flathead screwdriver
(not included).
INSTALLATION INSTRUCTIONS
1. Turn off power at circuit breaker or fuse box before
uninstalling existing device or installing new timer.
2. Remove existing wall plate and switch from wall box.
3. Make sure the following 3 wires are present in the wall
box. (see Diagram A)
a. 1 Hot Wire from circuit breaker box
b. 1 Load Wire to the device to be powered
c. 1 Neutral Wire
If these are not present, this Timing Device will not
function properly. Additional wiring to the wall box will be
required before installation of this timer can be completed.
4. Strip wires 1/2 inch. (see Diagram A)
From Timer
5. Use the included wire nuts
Black Wire
and securely twist together
Red Wire
to attach the timer wires to
White Wire
the building wires.
Green Wire
(see Diagram A)
*
or to ground post or screw terminal
Hot Wire Black Wire
Red Wire
Load Wire
Neutral Wire White Wire
Ground Wire Green Wire
Diagram A
AB13842
6. Insert timer into wall box (2-1/2 inch) being careful not to
ITEM #0192773
pinch any wires. Be sure timer is upright with the LCD screen
located at the top of the timer. (see Diagram B)
7. Fasten timer to the wall box using screws provided. (see
Diagram B)
8. Place the included rocker/decorator wall plate around the
timer face. (see Diagram B)
9. Restore power at circuit breaker or fuse box.
OPERATING INSTRUCTIONS
1 - 4
1. POWER-UP or RESET Sequence
a. Open the door.
b. Position the SYSTEM switch to "ON".
c. Press the "Reset" button with the tip of a small non-metallic
insulated tool, such as a pencil (not included).
d. Display will flash 12:00 AM on Monday for a few minutes. If no
other action taken, clock may engage with the incorrect time.
2. Setting the CURRENT TIME (Time Setup)
In Wall Box
a. Press the "Prog" button to enter Time Setup. The icon "CLK"
Hot Wire
will appear. NOTE: To enter Time Setup following or during
Load Wire
any other step in these instructions, wait for the colon ":"
Neutral Wire
between the hours and minutes to begin blinking and then
*
Ground Wire
press the "Prog" button.
b. Press the "Day" button to advance the day.
c. Press the "Hour" button to advance the hours, paying special
attention to the "A" which represents AM and "P" for PM.
d. Press the "Min" button to advance the minutes.
e. To save the Current Time settings and go directly to Event
Setup, immediately press the "Prog" button and skip to Step
3b below. To exit Time Setup without starting Event Setup,
wait about 6 seconds and the Programmed Time will be
automatically saved, or press any of the 3 unmarked
buttons to save your settings. NOTE: The colon ":" between
the hours and minutes will continually blink, indicating the
clock is running.
Diagram B
MO 12:00
A
CLR
Reset
Day Hour
CLR = Clear
= +/- 1hr
Prog Min R
R = Random
SYSTEM
OFF ON
3. Programming ON/OFF EVENTS (Event Setup)
a. Press the "Prog" button twice to enter Event Setup. The
icon "PROG" and "1 ON --:--" will appear. NOTE: The "1"
represents Program 1.
b. Using the "Hour" and "Min" buttons, enter desired ON
time.
c. Using the "Day" button, enter desired day(s) of week for
programming to be ON. Choose any individual day or
blocks of days including MO-FR, SA-SU, or MO-SU.
NOTE: To clear any programming entered in error in
Steps B or C above, press the "CLR" button. To recall
what was just cleared, press the "CLR" button a second
time.
d. Press the "Prog" button once to save the ON
programming. "PROG" and "1 OFF --:--" will now
appear.
e. Using the "Hour" and "Min" buttons, enter desired OFF
time.
f. Using the "Day" button, enter desired day(s) of week for
programming to be OFF. Choose any individual day or
blocks of days including MO-FR, SA-SU, or MO-SU.
NOTE: To clear any programming entered in error in
Steps E or F above, press the "CLR" button. To recall
what was just cleared, press the "CLR" button a second
time.
g. Press the "Prog" button once to save the OFF
programming and advance to the next event (up to 18
events available denoted by the numbers 1 through 18).
To end Event Setup, wait about 6 seconds and the
Programmed Events will be automatically saved, or
press any of the 3 unmarked buttons to save your
settings.
4. REVIEWING, CHANGING & DELETING Events
a. Press the "Prog" button twice to enter Event Setup. The
icon "PROG", "1 ON" and any specific programmed times
will appear.
b. TO REVIEW THE EVENTS, continue to press the "Prog"
button and it will cycle through all 18 events, one setting
at a time.
c. TO CHANGE AN EVENT, using the "Prog" button,
locate the event(s) to change and then use the "Hour",
"Min" and "Day" buttons accordingly. Press the "Prog"
button once to save changes and advance to the next
event.
d. TO DELETE AN EVENT, using the "Prog" button, locate
the event(s) to delete and then press the "CLR" button.
The hours, minutes and days will be deleted, and "--:--"
will appear. Press the "Prog" button once to confirm
deletion and advance to the next event. NOTE: When
deleting an event, be sure to delete both the ON and OFF
settings for that event. NOTE: To clear any programming
entered in error in Steps C or D above, press the "CLR"
button. To recall what was just cleared, press the "CLR"
button a second time.
e. To end Reviewing, Changing & Deleting of Events, wait
about 6 seconds and any changes will be automatically
saved, or press any of the 3 unmarked buttons to
save your settings.