Effects Screen - Behringer X32 User Manual

45
X32 RACK DIGITAL MIXER User Manual

7.6 Effects Screen

The effects screen controls various aspects of the eight internal effects
processors. On this screen, the user can select specific types of effects for
the eight internal effects processors, configure their input and output paths,
monitor their levels, and adjust the various effects parameters.
The home screen contains the following separate tabs:
1. Home: The home screen provides a general overview for all eight effects
processors, displaying what effect has been inserted in each of the eight slots,
as well as displaying input/output paths for each slot and the I/O signal levels.
2. FX1-8: These eight duplicate screens display all relevant data for the eight
separate effects processors, allowing the user to adjust all parameters for
the selected effect.
7.6.1 Effects Screen: Home Tab
The effects screen's home tab provides a high-level overview of the eight effect
processor slots, giving the user "at-a-glance" feedback on what effects they
have assigned to the slots, the console source and destination for each processor,
and the input/output levels for each processor.
To make adjustment on the effects screen's home tab, perform the
following steps:
1. Adjust the 1st encoder to select the input source for the currently highlighted
effect block. Signal path choices include:
• Insert Send
•
Mix Bus 1-16
2. Tap the 1st encoder to assign the currently selected input source.
3. Adjust the 2nd encoder to select the input source for the right side of the
currently highlighted effect block.
4. Tap the 2nd encoder to assign the currently selected input source.
TIP: To configure an effect as mono input and stereo output, set both input
sources to the same signal path.
5. Adjust the 5th encoder to scroll among the different available audio effects.
Choices include:
1. Hall Reverb 14. Rotary Speaker
2. Plate Reverb 15. Tremolo/Panner
3. Vintage Reverb 16. Delay & Chamber
4. Vintage Room 17. Chorus & Chamber
5. Ambience 18. Flanger & Chamber
6. Gated Reverb 19. Delay & Chorus
7. Reverse Reverb 20. Delay & Flanger
8. Stereo Delay 21. Dual Graphic EQ
9. 3-tap delay 22. Stereo Graphic EQ
10. Stereo chorus 23. Dual TruEQ
11. Stereo Flanger 24. Stereo TruEQ
12. Stereo Phaser 25. Wave Designer
13. Mood Filter 26. Precision Limiter
6. Tap the 5th encoder to assign the selected effect to the currently highlighted
effects slot.
7. Adjust the 6th encoder to scroll among the eight effects slots, to select one
for editing.
8. Tap the 6th encoder to go to the edit page for the currently highlighted
effects slot.
7.6.2 Effects Screen: FX 1-8 Tabs:
The effect editor tab allows you to edit the parameters for the specific effect
processor assigned to the corresponding effects slot.
In order to more closely simulate the look and feel of the outboard processors
that are no longer necessary with a digital console, the individual effects
processor screen provides a graphical representation of the effect processor's real
world physical counterpart. This provides greater ease of use to the user than a
simple text list of parameters.
To make adjustment on the FX screen's editing tab, perform the following steps:
1. Adjust the six rotary encoders to change the various effect parameters
shown at the bottom of the screen.
2. Use the Layer up/down buttons to switch the rotary encoders to a second
set of parameters for effects that contain more than six adjustable
parameters total.
3. When the effect processor has been edited to your satisfaction, push the 6th
encoder to go back to the FX home tab (or simply resume the mixing duties
in general).
4. See the FX Descriptions chapter for details on specific parameters.
27. Dual Enhancer
28. Stereo Enhancer
29. Dual Exciter
30. Stereo Exciter
31. Stereo Imager
32. Dual Guitar Amp
33. Stereo Guitar Amp
34. Dual Tube Stage
35. Stereo Tube Stage
36. Dual Pitch
37. Stereo Pitch
38. Dual De-Esser
39. Stereo De-Esser