Sharp MX-2300 G Service Manual page 135

26-2
Purpose : Setting
Function (Purpose) : Used to set the paper size of the large
capacity tray (LCC). (When the paper size
is changed, this simulation must be exe-
cuted to change the paper size in software.)
Section : Paper feed
Item : Setting
Operation/Procedure
Select the paper size with the buttons on the touch panel.
LCC 0 8.5 x 11 (Default: U.S.A, Canada, Inch)
1 A4 (Japan, AB_B, Europe, U.K,
Australia, AB_A)
2 B5
SIMULATION NO.26-02
TEST
SIZE SETUP
LCC 8.5 11
26-3
Purpose : Setting
Function (Purpose) : Used to set the specifications of the auditor.
Section : Auditor
Item : Specifications
Operation/Procedure
Select the set target with the button on the touch panel.
When a button is pressed, the set content is saved.
Button
Item
display
BUILT-IN P10 Built-in auditor mode
AUDITOR (standard mode) operation
EC1 The built-in auditor mode is
changed to EC1.
OUTSIDE NONE Normal operation
AUDITOR
P VENDOR1 Vendor mode for old-type coin
vendor. Control in the copy
mode only.
P OTHER Vendor mode for the other
external auditor connected to
the coin vendor I/F
DOC ADJ ON Document filing function
enabled
OFF Document filing function
disabled
PF ADJ ON Continuous paper feed is
performed.
OFF Continuous paper feed is not
performed.
VENDOR MODE1 Vendor mode 1
MODE (*)
MODE2 Vendor mode 2
MODE3 Vendor mode 3
0
CLOSE
B5
A4
1/1
Content Default
P10
NONE
OFF
OFF
MODE3
MX-2300/2700 N/G SIMULATION 7 – 29
Button
Item
display
COUNTUP FUSER_IN The charging timing is when
TIMING1 passing the sensor paper lead
edge after fusing.
FUSER_OUT The charging timing is when
passing the sensor paper rear
edge after fusing.
EXIT_OUT The charging timing is when
passing the (machine, right)
tray/after-process unit paper
exit sensor paper rear edge.
(*): AR-C260 series VENDOR MODE is supported.
The Insufficient money during
specified
quantity is
BLACK/
completed.
Diagnosis
COLOR (No
Remainder
setting
remainder
of money
of money)
left.
Condition 1 Condition 2
MODE1 Operation 1 Operation 2
MODE2 Operation 1 Operation 1
MODE3 Operation 1 Operation 3
Operation 1: Wait for auto clear setting time. Default, 60sec. Can
be changed by the system setting.
Operation 2: Auto clear is not made.
Operation 3: Setting is immediately cleared. The display returns to
the initial screen.
SIMULATION NO.26-03
TEST
AUDITOR SETUP
BUILT-IN AUDITOR
P10
OUTSIDE AUDITOR
NONE
DOC ADJ
ON
PF ADJ
ON
VENDOR MODE
MODE1
26-5
Purpose : Setting
Function (Purpose) : Used to set the count mode of the total
counter and the maintenance counter.
Section : —
Item : Counter
Operation/Procedure
1) Select the set item with [↑] [↓] buttons.
2) Enter the set value with 10-key.
3) Press [OK] button.
The set content in step 2) is saved. (Count-up number for A3
paper is 1 or 2.)
Item Display
A TOTAL (B/W) Total counter (BLACK)
B TOTAL (COL) Total counter (COLOR)
C MAINTENANCE Maintenance counter
(B/W) (BLACK)
D MAINTENANCE Maintenance counter
(COL) (COLOR)
E DEV (B/W) Developer counter
(BLACK)
F DEV (COL) Developer counter
(COLOR)
* 1 = Count up by 1
2 = Count up by 2
Content Default
EXIT_OUT
The
copy job specified
quantity is
COLOR
completed.
(Remainder
No
of money
remainder
left)
of money.
Condition 3 Condition 4
Operation 2 Operation 1
Operation 2 Operation 1
Operation 2 Operation 3
CLOSE
EC1
P VENDOR1
P OTHER
OFF
OFF
MODE3
MODE2
Setting
Content Default
range *
1 to 2 2
1 to 2 2
1 to 2 2
1 to 2 2
1 to 2 2
1 to 2 2
0
1/2