SAFETY PRECAUTIONS IMPORTANT SAFETY NOTICE Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent Shock, Fire, or other Hazards.
SERVICING PRECAUTIONS CAUTION: Before servicing receivers covered by this service unit under test. manual and its supplements and addenda, read and follow the 2. After removing an electrical assembly equipped with ES SAFETY PRECAUTIONS on page 3 of this publication. devices, place the assembly on a conductive surface such as NOTE: If unforeseen circumstances create conflict between the aluminum foil, to prevent electrostatic charge buildup or...
Page 5
IC Remove/Replacement Some chassis circuit boards have slotted holes (oblong) through Circuit Board Foil Repair which the IC leads are inserted and then bent flat against the Excessive heat applied to the copper foil of any printed circuit circuit foil. When holes are the slotted type, the following technique board will weaken the adhesive that bonds the foil to the circuit should be used to remove and replace the IC.
Picture Size 26 inch 26LC45/26LC46/26LC55 32 inch 32LC45/32LC46/32LC55/32LC56 37 inch 37LC45/37LC46/37LC55 42 inch 42LC45/42LC46/42LC55 Tuning System FVS 100 program PAL, 200 PR.(Option) Operating Environment 1) Temp : 0 ~ 40 deg 2) Humidity : 10 ~ 90 % Storage Environment...
Page 7
32” TFT WXGA LCD 32LC45/32LC46/32LC55/32LC56 37” TFT WXGA LCD 37LC45/37LC46/37LC55 42” TFT WXGA LCD 42LC45/42LC46/42LC55 Frequency range H : 45 ~ 50Khz, V : 47 ~ 63Hz 26, 32, 37 inch H : 44.65 ~ 50.35Khz, V : 47 ~ 63Hz...
Page 8
3. Optical Feature 3-1. 26” LCD Module-LPL Item Specification Min. Typ. Max. Remark Viewing Angle<CR>10> R/L, U/D 178, 178 Luminance Luminance (cd/m 26” Variation MAX / MIN Contrast Ratio CR(26”) All white/All black (With AI)(26”) 1000 1400 All white/All black CIE Color Coordinates White Typ.
Page 9
3-4. Optical Feature(37” LCD Module) Item Specification Min. Typ. Max. Remark Viewing Angle<CR>10> R/L, U/D 178, 178 Luminance Luminance (cd/m 37” Variation MAX / MIN Contrast Ratio CR(37”) All white/All black (With AI)(32”) 1200 1600 All white/All black CIE Color Coordinates White Typ.
Page 10
4. Component Video Input (Y, P Specification Remark Resolution H-freq(kHz) V-freq(Hz) 720 x 480 15.73 60.00 SDTV, DVD 480i 720 x 480 15.63 59.94 SDTV, DVD 480i 720 x 480 31.47 59.94 480p 720 x 576 15.625 50.00 SDTV, DVD 625 Line 720 x 576 31.25 50.00...
Page 13
7. Mechanical specification 1) 26LC45/26LC55(TBD) Item Content Unit Remark Product Widt(W) Length(D) Height(H) Dimension Before Packing 676.4 529.2 With Stant After Packing Box Out Size Product Only SET 10.04 With BOX 13.04 2) 32LC45(TBD) Item Content Unit Remark Product Widt(W) Length(D) Height(H) Dimension...
[Channel Download] [Write Batch]. This spec. sheet is applied to all of the LD73A chassis Next, select proper binary file(*.bin) including the CH manufactured at LG TV Plant all over the world. information for each model at [Channel Download] => [NVRAM File].
Page 15
4.1.1 Method of Auto RF / AV / S-VIDEO Color Balance 4.3 Adjustment of Component (PAL_BGDHI). [ Required Equipments 1) Input the Video Signal: 7 Color Bar signal into AV3. Remote controller for adjustment 2) Set the PSM to Dynamic mode in the Picture menu. MSPG-925FS Pattern Generator.
5.1 Manual white Balance One of R Gain / G Gain / B Gain should be kept on 80, and others are controlled lowering from 80 1) Press 'power on' of the control R/C, set heat run to white by pressing G , and heat run over 15 minutes (Set: RS-233 Host: PC, Baud Rate: 115200bps, Download: Cortez).