Product Description And Specifications; Product Features; Initial Operation - Bosch 102 Original Instructions Manual

OBJ_BUCH-1497-003.book Page 10 Thursday, November 29, 2012 10:02 AM
10 | English
 In case of damage and improper use of the battery, va-
pours may be emitted. Ventilate the area and seek
medical help in case of complaints. The vapours can irri-
tate the respiratory system.
 Recharge only with the charger specified by the manu-
facturer. A charger that is suitable for one type of battery
pack may create a risk of fire when used with another bat-
tery pack.
 Use the battery only in conjunction with your Bosch
cordless worklight. This measure alone protects the bat-
tery against dangerous overload.
 Use only original Bosch batteries with the voltage list-
ed on the nameplate of your cordless worklight. When
using other batteries, e. g. imitations, reconditioned bat-
teries or other brands, there is danger of injury as well as
property damage through exploding batteries.
Technical Data
Cordless Worklight
Article number
Rated voltage
Lighting duration, approx.
Operating temperature
Storage temperature
Weight according to
EPTA-Procedure 01/2003
Assembly
Battery Charging (Accessory) (see figure A)
 Use only the battery chargers listed on the accessories
page. Only these battery chargers are matched to the lith-
ium ion battery of your cordless worklight.
Note: The battery is supplied partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The Lithium-Ion battery can be charged at any time without
reducing its service life. Interrupting the charging procedure
does not damage the battery.
The lithium ion battery is protected against deep discharging
by the "Electronic Cell Protection (ECP)". When the battery is
empty, the cordless worklight is switched off by means of a
protective circuit.
 Do not continue to press the On/Off switch after the
cordless worklight has been automatically switched
off. The battery can be damaged.
To remove the battery 5, press the battery unlocking button 4
and pull the battery upward out of the battery port. Do not ex-
ert any force when doing this.
1 609 92A 01X | (29.11.12)
Product Description and
Specifications
Intended Use
The cordless worklight is intended for hand-guided illumina-
tion with regard to space within dry areas.

Product Features

The numbering of the product features refers to the illustra-
tion of the cordless worklight on the graphics page.
1 On/Off switch
2 Lens plate
3 Heat sink
4 Battery unlocking button*
5 Battery pack*
6 Support bracket for adjustment of the illumination angle
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
GLI PortaLED 102
3 601 D46 0..
V= 14.4 18
min/Ah 57 70
°C –10...+40 –10...+40 –10...+40 –10...+40 –10...+40 –10...+40
°C –15...+50 –15...+50 –15...+50 –15...+50 –15...+50 –15...+50
kg 3.7 3.7
The battery is equipped with a NTC temperature control
which allows charging only within a temperature range of be-
tween 0 °C and 45 °C. A long battery service life is achieved
in this manner.
Observe the notes for disposal.
Operation

Initial Operation

Inserting the battery (see figure A)
 Use only original Bosch lithium ion batteries with the
voltage listed on the nameplate of your cordless work-
light. Using other batteries can lead to injuries and pose a
fire hazard.
Insert the charged battery 5 into the battery port until it can
be felt to engage and is seated flush.
Switching On and Off
To start the cordless worklight, press the On/Off switch 1.
To switch off the cordless worklight, press the On/Off switch
1 again.
Switching on again is not possible until 1 second has elapsed
after switching off.
To save energy, only switch the cordless worklight on when
using it.
GLI PortaLED 136 GLI PortaLED 238
3 601 D46 1.. 3 601 D46 2..
14.4 18 14.4
57 70 57
3.9 3.9 4.3
18
70
4.3
Bosch Power Tools