Download Print this page

Krell Industries MP3 Docking Station User Manual

Krell industries inc. mp3 docking station user manual

Advertisement

Quick Links

Specifications
KID SPECIFICATIONS
Inputs
1 30-pin iPod-device type
1 3-conductor 3.5 mm connector
Audio Outputs
1 pair balanced via XLR connectors
1 pair single-ended via RCA connectors
Video Outputs
1 S-Video via a DIN connector
1 Composite via a RCA connector
Control Inputs
1 RS-232 input via a 9-pin D-subminiature connector
Control Outputs
1 12 VDC trigger output via 2-conductor
3.5 mm connectors (500 milliamps maximum
per output)
Input impedance
Single-ended: 47.5 k Ohms
Output impedance
Balanced: 50 Ohms
Single-ended: 25 Ohms
Volume Control
256-step Digital Control
Input Overload
Single-ended: 4 Vrms
Output Overload
Balanced: 16 Vrms
Single-ended: 8 Vrms
Frequency Response
20 Hz to 20 kHz +0.7 dB, -0.0 dB
0.1 Hz to 90 kHz +0.7, -3 dB
Tone Control Range
Bass: +8 dB, -7 dB
Treble: +6 dB, -6 dB
Total Harmonic Distortion Plus Noise
Balanced Output: <0.002%, 20 Hz to 20 kHz,
4 V RMS or 4 mA rms
Signal-to-noise Ratio
Wideband, Unweighted: >94 dB
"A" Weighted: >97 dB
Power Consumption
Standby: 10 W
Power on: 25 W
Dimensions
Inches: 13 W x 2.8 H x 10.9 D
Centimeters: 33.0 W x 7.0 H x 27.7 D
Weight
Unit Only: 10 lb., 4.5 kg
Shipped: 14 lb., 6.4 kg
All operational features, functions, specifications, and
policies are subject to change without notification.
12
Krell
/ Papa Dock
PAPA DOCK SPECIFICATIONS
Frequency Response
20 Hz to 20 kHz, +0, -0.15 dB
<0.2 Hz to 110 kHz,+0 dB, -3 dB
Signal-to-noise Ratio
Wideband, unweighted, referred to full power output:
>108 dB
"A" weighted: >116 dB
Gain: 26.2 dB
Total Harmonic Distortion (THD)
< 0.03%@ 1 kHz, at 150 W, 8 Ohms
< 0.20%@ 20 kHz, at 150 W, 8 Ohms
Input Impedance
90 kOhms
Input Sensitivity
1.70 Vrms
Output Power, each channel driven:
150 Wrms @ 8 Ohms
300 Wrms @ 4 Ohms
Output voltage
98 V peak-to-peak, 35 Vrms
Output current: 15 A peak
Slew Rate: 50 V/µs
Output Impedance
<0.073 Ohms at 20 Hz
<0.084 Ohms, 20 Hz to 20 kHz<
Dampening Factor
110 at 20 Hz, referred to 8 Ohms
95, 20 Hz to 20 kHz, referred to 8 Ohms
Power Consumption
Stand-by: 25 W, Idle: 55 W, Maximum: 900 W
Heat Output, BTU/hr.
Stand-by: 85, Idle: 190, Maximum: 1100
Inputs
1 40-pin KID connector
1 RS-232 (to control KID) via a 9-pin
D-subminiature connector
Outputs
2 channel via 5-way binding posts
Remote Connectors
One 12 VDC output (12 V trigger), 30 mA maxi-
mum, via a 3.5 mm connector
S-Video (from KID) via mini-DIN connector
1 composite video (from KID) via RCA connector
Dimensions
Inches: 17.3 W x 5.7 H x 16.3 D
Centimeters: 43.8 W x 14.5 H x 41.3 D
Weight
Unit Only: 39 lb., 17.6 kg
Shipped: 49 lb., 22.2 kg
Your KID product serial number is:
P/N 301038 v 08.0
Owner's Reference
POWER
BASS
POWER
Krell Interface Dock
Papa Dock
TREBLE
VOLUME
AUX
INPUT

Advertisement

loading

Summary of Contents for Krell Industries MP3 Docking Station

  • Page 1 Specifications KID SPECIFICATIONS PAPA DOCK SPECIFICATIONS Inputs Frequency Response 1 30-pin iPod-device type 20 Hz to 20 kHz, +0, -0.15 dB 1 3-conductor 3.5 mm connector <0.2 Hz to 110 kHz,+0 dB, -3 dB Audio Outputs Signal-to-noise Ratio 1 pair balanced via XLR connectors Wideband, unweighted, referred to full power output: 1 pair single-ended via RCA connectors >108 dB...
  • Page 2: Remote Only

    (89/336/EEC) and the low-voltage directive (73/23/EEC). Krell ® is a registered trademark of Krell Industries, Inc., and is restricted for use buy Krell Industries, Inc., its subsidiaries, and authorized agents. iPod is a trade- mark of Apple, Inc., registered in the U.S. and other Countries.
  • Page 3 Front Panel Functions Remote Control Functions FIGURE 6 KID Front Panel Docking station inset: Inset shows iPOD-device support affixed to the top cover of the chassis with the dock connector below TOP ONLY FIGURE 7 KID Remote Control 22 Docking station (see inset above) FRONT PANEL ONLY 23 Auxiliary input FRONT PANEL AND REMOTE...
  • Page 4 Unpacking the KID Unpacking the Papa Dock UNPACK THE KID One person can remove the KID from its shipping 4. Set the remote and the AC power cord aside, box safely and easily. for later use. 1. Open the shipping carton top flap. You see the 5.
  • Page 5: Install The Battery

    AC power for the Papa Dock. FIGURE 7 Papa Dock Back Panel Connections RIGHT OUTPUT PAPA DOCK PAPA DOCK KRELL INDUSTRIES, INC. 45 CONNAIR ROAD ORANGE, CT 06477-3650 VIDEO OUT 12VDC 30 mA MAX.
  • Page 6 Placement Considerations, continued The KID / Papa Dock Connection PLACEMENT CONSIDERATIONS , continued Component Ventilation, continued The air space between the chassis and shelf must If the KID is placed in a closed cabinet, more than be unobstructed. eight inches (20 cm) of clearance may need to be provided above and below the component, or The Papa Dock requires ventilation clearance: small fans may be needed to increase ventilation.