Height Of Cut; Assembly Instructions; Adjusting The Cutting Height - Electrolux 32cm Lawn Mower Important Information Manual

10. Stop the lawnmower and remove the safety key
before moving the lawnmower across surfaces
other than grass and when transporting the
lawnmower to and from the area to be mowed.
11. Never operate the lawnmower with damaged
guards or without guards in place.
12. Keep hands and feet away from the cutting
means at all times and especially when
switching on the motor.
13. Do not tilt the lawnmower when the motor is
running, except when starting and stopping. In
this case, do not tilt more than absolutely
necessary and lift only the part which is away
from the operator. Always ensure that both
hands are in the operating position before
returning the appliance to the ground.
14. Do not stand in front of the grass discharge
chute when you start the motor.
15. Do not put hands near the grass discharge chute
whilst the motor is running.
16. Never pick up or carry a lawnmower while the
motor is running
17. Stop the lawnmower and remove the safety key:
- before leaving the mower unattended for any
period;
- before clearing a blockage;
- before checking, cleaning or working on the
appliance;
- if you hit an object. Do not use your lawnmower
until you are sure that the entire lawnmower is in
Assembly of Lower Handles to Deck
1. Locate 2 screws into the holes in the handles.
2. Using a pozidrive screwdriver, secure the screws
into the lower handles, ensuring the point of the
screw stays inside the handle. (A)
3. Insert lower handle with screw attached into hole
in the deck and fully tighten screws. Repeat on
the other side. (B)
NOTE: The screw will form its own thread.
Fitting Upper Handles to Lower Handles.(C)
1. Ensure the upper handle is located correctly with
the lock-off button on the switchbox uppermost.
G1 - wheel, G2 - hub cap, G3 - fixing bolt,
G4 - holes, G5 - mounting plate
• Height of cut is adjusted by raising or
lowering the wheels.
• NOTE: All 4 wheels must be adjusted to the
same position.
• NOTE: A medium height of cut is
recommended for most lawns.
1. To remove the wheel assembly turn the wheel
hub in an anti-clockwise direction.(E)
2. Select one of the 3 holes in the mounting plate
and note it as the other 3 wheels will need to be
adjusted to the same position.(G)
Safety Precautions
-
Maintenance and storage
1. Keep all nuts, bolts and screws tight to be sure
2. Check the grassbox/grassbag frequently for
3
4. Only use the replacement blade, blade bolt and
5. Allow the motor to cool before storing in any
6. To reduce fire hazard, keep the motor, battery
7. Be careful during adjustment of the machine to
8. Store in a cool, dry place where your lawnmower
Transport Safety
1. Remove the safety key to prevent accidental
2. Carefully fold the handle onto the machine.
3. Make sure the cable is not trapped

Assembly Instructions

2. Ensure the upper handle and the lower handle
3. Insert the nut into the handle knob. (if applicable)
4. Fit the bolts, washers and handle knobs.
5. Fit the cable to the handles with the clips
Grassbox Assembly. (D)
1. Locate grassbox upper into grassbox lower. Align
2. Clip the two halves together.
3. Ensure all clips are securely connected.

Adjusting the Cutting Height

3. Locate fixing bolt through hole in hub cap, wheel
4. Turn the wheel hub in a clockwise direction until
5. Using the same height adjustment position
• NOTE: To reduce the cutting load, the rear
a safe operating condition;
if the lawnmower starts to vibrate abnormally.
Check immediately. Excessive vibration can
cause injury.
the lawnmower is in safe working condition.
wear or deterioration.
Replace worn or damaged parts for safety.
blade adaptor specified for this product.
enclosure.
compartment and storage area free of grass,
leaves or excessive grease.
prevent entrapment of the fingers between
moving blades and fixed parts of the machine.
is protected from damage.
starting.
are aligned correctly.
provided, making sure the cables are not trapped
between the upper and lower handles.
clips, ensure all clips are correctly located.
and selected hole in mounting plate.(G)
the wheel assembly is securely located to the
deck.(F)
repeat the procedure for the other 3 wheels.
wheels may be raised higher than the front
wheels.

HEIGHT OF CUT

Low
Medium
High
WHEELS
Hole 1
Hole 2
Hole 3
ENGLISH - 2