Foot Switch Assign; Foot Switch Assign List - Korg TRITON Le Electric Keyboard Parameter Manual

The A-mode functions of the REALTIME CONTROLS
are fixed.
Knob1-A: LPF Cutoff (Filter LPF Cutoff: CC#74)
Control the low pass filter cutoff frequency of the filter.
Simultaneously, CC#74 will be transmitted.
Knob2-A: Resonance/HPF
(Filter Resonance/HPF Cutoff: CC#71)
Control the resonance level or the cutoff frequency of the
high pass filter. If the program "Filter Type" is Low Pass
Resonance, the resonance level will be controlled. If "Filter
Type" is Low Pass & High Pass, the cutoff frequency of the
high pass filter will be controlled. Simultaneously, CC#71
will be transmitted.
Knob3-A: EG-Intensity (Filter EG Intensity: CC#79)
Control the filter EG intensity. Simultaneously, CC#79 will
be transmitted.
Knob4-A: EG-Release (Filter, Amplifier EG Release: CC#72)
Control the release time of the filter and amplifier EG.
Simultaneously, CC#72 will be transmitted.

Foot Switch Assign List

Off
Foot SW (CC#82)
Portamento SW (CC#65) Control portamento on/off.
Sostenuto (CC#66)
Soft (CC#67)
Arpeggio SW
Program Up
Program Down
Song Start/Stop
Song Punch In/Out
Cue Repeat Control
Portamento SW (CC#65)
When the "Mode (Oscillator Mode)" (PROG 2.1–1a) is Sin-
gle, turning the switch on will apply portamento regardless
of the "Enable (Porta. Enable)" (PROG 3.1–1c) setting, and
turning the switch off will not apply portamento.
If "Mode (Oscillator Mode)" is Double, and if the "Enable
(Porta. Enable)" setting is the same for OSC1 and 2 (i.e.,
Enable or Disable for both OSC1 and 2), then portamento
will be applied to OSC1 and 2 when the switch is turned on,
and portamento will not be applied to OSC1 and 2 when the
switch is turned off.
If the "Enable (Porta. Enable)" setting is different for OSC1
and 2 (i.e., OSC1 is Enable and OSC2 is Disable, or OSC1 is
Disable and OSC2 is Enable), then portamento will be
applied to the OSC whose setting is Enable when the switch
is turned on, and portamento will be applied to neither OSC
when the switch is turned off.
222
The connected foot switch will not function.
Alternate Modulation or Effect Dynamic Modulation can be controlled. To control these, select Foot SW:#82 for "AMS" or
FSW#82 for "Dmod Src."
Control the sostenuto effect (which holds only the keys (Note No.) that were being held at the moment that the pedal
switch was turned on).
Turn the soft pedal effect on/off.
Turn the arpeggiator on/off. The NRPN message [Bn 63 00 Bn 62 02 Bn 06 00 (off) or 7F (on)] will be transmitted each
time this is turned on/off.
The switch can be used to select programs or combinations. When in PROG 1.1: Play, the program that follows the cur-
rently selected program will be selected. When in COMBI 1.1: Play, the combination that follows the currently selected
combination will be selected. Simultaneously, a Bank Select message and Program Change message will be transmit-
ted.
The switch can be used to select programs or combinations. When in PROG 1.1: Play, the program that precedes the
currently selected program will be selected. When in COMBI 1.1: Play, the combination that precedes the currently
selected combination will be selected. Simultaneously, a Bank Select message and Program Change message will be
transmitted.
The switch can be used to start/stop the sequencer. Simultaneously, a MIDI Start or Stop message will be transmitted.
If "REC Setup"(SEQ 1.1–6a) is set to Manual Punch In, the switch can be used to punch-in and punch-out when record-
ing on the sequencer.
This can be used if in Cue List, the "Rep (Cue Edit-Repeat)" (SEQ 2.1–1b) setting of each step has been set to FS. Turn-
ing the pedal switch on while that step is repeating will be the trigger for advancing to the next step. When the end of the
song is reached, this will advance to the next step (song).

Foot Switch Assign

You can assign the function of an assignable switch (sepa-
rately sold Korg PS-1 option) connected to the ASSIGN-
ABLE SWITCH jack.
• This setting is made in GLOBAL 1.1: System Foot page
"Foot SW Assign" (1.1–3a).
If you select a function that includes a CC#, that MIDI
control change message will be transmitted each time
the switch is turned on/off. (Off: 0, On: 127)