Aiwa NSX-AJ800 Service Manual page 33

Pin No. Pin Name
56 KARAOKE/P23
57 DEMO/P22
58 DOLBY/P21
59 AM-ST/P20
60 SOFT/P19
61 SW/P18
62 FM1/P17
PANO/P16
63
64 AM-9K/10K/P15
65 CASINO/P14
66 REA/P13
67 CST1/P12
68 CAM1/P11
69 AUTO2/P10
70 AUTO1/P9
71 CAM2/P8
72 VDD4
73 REB/P7
74 CST2/P6
75 M-GEQ/P5
76 R+1/P4
77 1+1/P3
78 P-CL/P2
79 P-OP/P1
80 BOX1
81 BOX2
82 I-VOL2
83 I-VOL1
84 I-IFC
85 O-MP-CL
86 O-MP-OP
87 O-PLL CE
88 O-KSCAN
89 VSS2
90 VDD2
91 STBY-LED
92 O-MOTOR
93 O-SOL1
94 O-SOL2
95 O-CD-DATA
96 O-CD-CLK
I/O
I/O Karaoke input to diode<LH only>/FL segment P23 output.
I/O Demo (on the stop) diode input (Not used)/FL segment P22 output.
I/O DECK DOLBYdiode input (Not used)/FL segment P21 output.
I/O AM-ST select diode (Not used)/FL segment P20 output.
I/O DECK SOFT diode input (Not used)/FL segment P19 output.
I/O SW diode input (Not used)/FL segment P18 output.
I/O FM1 diode input (Not used)/FL segment P17 output.
I/O Panorama diode input/FL segment P16 output.
I/O AM-9K/10Kselect diode input/FL segment P15 output.
I/O Initial casino diode input<LH only>/FL segment P14 output.
I/O DECK2 side A recordable switch. "L" : REC<LH only>/FL segment P13 output.
I/O DECK1 cassette detection switch data input. "L" : ON/FL segment P12 output.
I/O DECK1 CAM STOP switch data input. "L" : ON/FL segment P11 output.
I/O DECK2 AUTO STOP switch data input/FL segment P10 output.
I/O DECK1 AUTO STOP switch data input/FL segment P9 output.
I/O DECK2 CAM switch data input. "L" : ON/FL segment P8 output.
- Digital power supply pin.
I/O DECK2 side B recordable switch. "L" : REC<LH only>/FL segment P7 output.
I/O DECK2 cassette detection switch data input. "L" : ON/FL segment P6 output.
I/O Manual GEQ diode input<LH only>/FL segment P5 output.
I/O DECK R+1 diode input<U only>/FL segment P4 output.
I/O DECK 1+1 diode input (Not used)/FL segment P3 output.
I/O (Not used)/FL segment P2 output.
I/O (Not used)/FL segment P1 output.
I Cassette BOX1 open/close detect input.
I Cassette BOX1 open/close detect input.
I Volume rotary encoder input 2.
I Volume rotary encoder input 1.
I Tuner IF count input.
O Moving panel close output.
O Moving panel open output.
O Tuner PLL IC chip enable output.
O Initial scan output.
- Connected to ground.
- Digital power supply pin.
O Standby LED ON/OFF output. "L" : ON
O Cassette deck motor control output.
O DECK1 solenoid output.
O DECK2 solenoid output.
O CD IC control data output.
O CD IC control clock output.
Description
– 33 –