Test Mode - Sony STR-KG800 Service Manual

STR-KG800
QQ
3 7 63 1515 0
FL CHECK MODE
All fl uorescent segments are tested. When this test is activated, all
segments turn on at the same time, then each segment turns on one
after another.
Procedure:
1. When pressing the [TUNING MODE] and [DISPLAY] but-
tons, press the [ ] button to turn on the main power.
?/1
2. All segments turn on.
LFE SP A D EX PL II x PL
SW
SP B HDMI COAX
L C R
SL S SR
SBL SB SBR
3. Turn the [INPUT SELECTOR] dial.
4. Test pattern 1 turn on.
LFE D EX PL II x
SP B HDMI COAX
L R
S
5. Turn the [INPUT SELECTOR] dial once again.
6. Test pattern 2 turn on.
D PL
SW
C
SL SR
SBL SB SBR
7. Turn the [INPUT SELECTOR] dial once again. All segments
turn off.
8. Every turning of the [INPUT SELECTOR] dial turns on each
segment one after another on the same order.
TE
L 13942296513
S.F. CLEAR MODE
The preset sound fi led is cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. While pressing the [2CH] button, press the [
on the main power.
2. The message "S.F CLR." appears and initialization is per-
formed.
VERSION CHECK MODE
When this mode is used the model, the destination and the software
version number are displayed.
Procedure:
1. While pressing the [SPEAKERS (ON/OFF)] and [DISPLAY] but-
tons, press the [ ] button to turn on the main power.
?/1
2. The model, the distination and the software version number
appear.
KEY CHECK MODE
This mode is used to check the key.
Procedure:
1. While pressing the [SPEAKERS (ON/OFF)] and [2CH] but-
tons, press the [ ] button to turn on the main power.
?/1
2. The message "REST 13" appears.
3. Every pressing of any button other than the [
down the buttons. The buttons which are already counted once
are not counted again.
www
4. When all buttons are pressed, the message "REST 00" ap-
pears.
.
12
http://www.xiaoyu163.com
SECTION 4

TEST MODE

OPT DTS-ES 96 / 24 CAT RDS ST
MEMORY
NEO:6 SAT D.RANGE MONO
dB
k Hz
mft.
MHz
DTS-ES RDS ST
NEO:6 SAT D.RANGE MONO
k
m
MHz
DTS CAT ST
MEMORY
dB
Hz
ft.
] button to turn
?/1
] button counts
?/1
x ao
y
i
http://www.xiaoyu163.com
8
SWAP ALL MODE
When this mode is used, output the audio signal of front L/R chan-
nel to all channel.
Procedure:
1. While pressing the [MEMORY/ENTER] and [DISPLAY] but-
tons, press the [ ] button to turn on the main power.
?/1
2. The message "DSP TEST" appears.
3. Press the [AMP MENU] button on the remote commander, and
the message "9_DSPTST" appears.
4. Press the [b] button on the remote commander to enter the
DSP test mode menu.
5. Press the [v] button on the remote commander twice to enter
the swap mode, and the message "SWP.AUTO" appears.
6. Press the [b] button on the remote commander twice to select
"SWP.[]ALL".
SHIPMENT MODE
All preset contents are cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. While pressing the [SPEAKERS (ON/OFF)] and [MUSIC] but-
tons, press the [ ] button to turn on the main power.
?/1
2. The message "CLEARING" appears.
DCAC FACTORY TEST MODE
DCAC Factory Test mode have two stages:
1. DCAC DSP Data Line Checking
2. DCAC board Checking
Q Q
Start
DSP Data Line
3 6 7 1 3
Check
Factory Test System Setup
Receiver
DCAC MIC
SPK Front Left
1. When power off :
While pressing the [MEMORY/ENTER] and [MOVIE] but-
tons, press the [ ] button to turn on the main power.
?/1
"DCAC FTM" appears.
Afterward, press the [TUNING MODE] to start DCAC factory
test mode.
u163
.
2 9 9 4 2 8
Pass Pass
Auto Cal Mic
1 5 0 5 8 2 9 9 4
Check
m
co
9 9
2 8 9 9
END