Panasonic TC-P42G15 Operating Instructions Manual page 37

(Continued)
Adjustments/Configurations (alternatives)
• All •
IChannel surf mode
I
Language
Selects the screen menu language (p. 16)
Sets the mode to select the channel with Channel up/down button
(All/Favorite/Digital only/Analog only)
• Favorite: Only channels registered as FAVORITE (p. 20)
Adjusts the clock (p. 18)
ICIOCk
Sets channels (p. 50) IANT/Cable setup
Selects the terminal and label of the external equipment (p. 53)
[Component 1/Component 2/HDMI1/HDMI2/HDMI3Nideo 1Nideo 2]
To prevent howling, stops output of audio specified in this menu. (p. 53) (On/Off)
Prevents "Image retention" with Wobbling. (Automatic/Periodic)
6'
Automatic: Shifts the display image automatically.
• Periodic: Shifts the display image every (1/2/3/4) minutes according to what was set in the "Time (minutes)" menu.
Sets the time for "Pixel orbiter-Periodic" setting. (1/2/3/4)
Change the brightness of the side bar (Off/Dark/Mid/Bright) (4:3 mode only)
• The recommended setting is "Bright" to prevent panel "Image retention". (p. 60)
Press "OK" to start "Scrolling" on the screen (p. 60)
Controls equipment connected to HOMI terminals (p. 40) (On/Off)
" "Power off link", "Power on link", "Stand-by power save", "Auto power stand-by" and "Default speakers" cannot be selected if "Off' is set.
Sets "Power on link" of HOMI connection equipment (p. 40) (Yes/No)
Sets "Power off link" of HOMI connection equipment (p. 40) (Yes/No)
Set "Stand-by power save" of HOMI connection equipment. (p. 40) (NolYes)
Set "Auto power stand-by" of HOMI connection equipment. (p. 40)
(NolYes (with reminder)lYes (no reminder)
Selects the default speakers (p. 40) (TV/Theater)
Sets Network setting (p. 44)
Sets VIERA CAST setting (p. 46)
Set Network Camera status. (Search/Registration/Connection/Oeleting/Oefault setting etc.) (p. 30)
To conserve energy, the TV automatically turns off when NO SIGNAL and NO OPERATION is performed
for more than 10 minutes. (Enable/Disable)
Note
• Not in use when setting "Auto power on", "On/Off Timer", "Lock", "SO mode" or Digital channel.
• "No signal for 10 minutes was activated" will be displayed for about 10 seconds when the TV is turned
on for the first time after turning the power off by "No signal for 10 minutes".
• The on-screen display will flash 3, 2 and 1 to indicate the last three (3) remaining minutes prior to the shut-off.
To conserve energy, the TV automatically turns off when no operation of remote or side panel key
continues for more than 3 hours. (Enable/Disable)
Note
• Not in use when setting "Auto power on", "On/Off Timer" or PC input display.
@
"No activity for 3 hours was activated" will be displayed for about 10 seconds when the TV is turned on
for the first time after turning the power off by "No activity for 3 hours".
• The on-screen display will flash 3, 2 and 1 to indicate the last three (3) remaining minutes prior to the shut-off.
IPixel orbiter
Ut.nMMI
Inme (minutesl
14:3 side barsMmfiii1iM1
IScrolling bar
IVIERA Link
I
Power on link
I
Power off link
• No •
I
Default speakers
I
Network setting
IVIERA CAST setting
I
Network cameras list
No signal for 10 minutes
• Enable •
No activity for 3 hours
• DIsable •
•
_ I
"00
o·~
.....
c .....
. , 0
CDC
en en
OCD
c~
5.
CD
.;:'
..cc
c
0)11
=c
.....
;:,
':<(,,)
CD~
..... 0
(");:,
-:.......en
Turns TV On automatically when the cable box or a connected device is turned On. (NolYes)
TV AC cord must be plugged into this device. TV comes on every time the power is restored.
• The "Sleep" timer, "On / Off timer", and "First time setup" will not function if "Auto power on" is set. (p. 54)
Set "Movie", "Thumbnail" or "Slideshow" to play back SO cards automatically.
(SlideshowlThumbnaiI/Movie/Set later/Off)
I
Auto power on
Play
so
card automatically
• Set later •
Displays TV version and software license.
IAbout
Performing Reset will clear all items set with Setup, such as channel settings. (p. 50)
I Reset to defaults
Adjustments/Configurations (alternatives)
Sets the mode to select the channel with Channel up/down button (All/Favorite/Digital only/Analog only)
Sets favorite channels. (p. 20)
Changes the station identifier. (p. 51)
Checks the signal strength if interference or freezing occurs on a digital image. (p. 51)
37