Table of Contents
Advertisement
USING THE RADIO SYSTEM
The TQi Radio System has been pre-adjusted at the factory. The
adjustment should be checked before running the model in case of
movement during shipping. Here's how:
1. Turn the transmitter switch on. The status LED on the transmitter
should be solid green (not flashing).
2. Elevate the model on a block or a stand so that all the tires are
off the ground. Make sure your hands are clear of the moving
parts of the model.
3. Plug the battery pack in the model into the speed control.
4. The on/off switch is integrated into the speed control. Press and
release the EZ-Set button on the speed control to turn the model
on. The LED will shine RED or GREEN (see note below). To turn
the VXL-3s off, press the set button until the LED turns off. Note:
If the model is factory equipped with LiPo batteries, the LED will be
green, indicating that Low-Voltage Detection is activated. If the
model is factory equipped with NiMH batteries, the LED will be red,
indicating that Low-Voltage Detection is disabled. Never use LiPo
batteries while Low-Voltage Detection is disabled. See page 17 for
more on VXL-3s setup and operation.
5. Turn the steering wheel on the transmitter back and forth and
check for rapid operation of the steering servo. Also, check that
the steering mechanism is not loose or binding. If the steering
operates slowly, check for weak batteries.
6. When looking down at the
0°
model, the front wheels
should be pointing straight
ahead. If the wheels are
turned slightly to the left
or right, slowly adjust the
steering trim control on the
transmitter until they are pointing straight ahead.
°
-1
7. Gently operate the throttle trigger to ensure that you have
forward and reverse operation, and that the motor stops when
the throttle trigger is at neutral. WARNING: Do not apply full
throttle in forward or reverse while the model is elevated.
8. Once adjustments are made, turn off the VXL-3s, unplug the battery
from the model, then turn off the hand-held transmitter.
0
Range-Testing the Radio System
Before each running session with your model, you should range-test
your radio system to ensure that it operates properly.
1. Turn on the radio system and check its operation as described in
the previous section.
2. Have a friend hold the model. Make sure hands and clothing are
clear of the wheels and other moving parts on the model.
3. Make sure your transmitter antenna is upright, and then walk
away from the model with the transmitter until you reach the
farthest distance you plan to operate the model.
4. Operate the controls on the transmitter once again to be sure
that the model responds correctly.
5. Do not attempt to operate the model if there is any problem
with the radio system or any external interference with your
radio signal at your location.
Higher Speeds Require Greater Distance
The faster you drive your Slash VXL, the more quickly it will near
the limit of radio range. At 60mph, a model can cover 88 feet
every second! It's a thrill, but use caution to keep your model in
range. If you want to see your Slash VXL achieve its maximum
speed, it is best to position yourself in the middle of the truck's
running area, not the far end, so you drive the truck towards and
past your position. In addition to maximizing the radio's range,
this technique will keep your model closer to you, making it
easier to see and control.
0°
No matter how fast or far you drive your Slash VXL, always leave
adequate space between you, the model, and others. Never drive
directly toward yourself or others.
TQi Binding Instructions
For proper operation, the transmitter and receiver must be
°
°
electronically "bound." This has been done for you at the factory.
-1
-1.5
Should you ever need to re-bind the system or bind to another
transmitter or receiver, follow these instructions. Note: The receiver
must be connected to a 4.8-6.0v (nominal) power source for binding,
and the transmitter and receiver must be within 5 feet of each other.
1. Press and hold the transmitter's SET button as you switch the
transmitter on. The transmitter's LED will flash red slowly.
°
°
0
Release the SET button.
2. Press and hold the receiver's LINK button as you switch on
TRAXXAS TQ
RADIO & VELINEON POWER SYSTEM
i
°
-1.5
Using Reverse: While driving,
push the throttle trigger
forward to apply brakes.
Once stopped, return the
throttle trigger to neutral.
Push the throttle trigger
forward again to engage
proportional reverse.
6,7
SLASH VXL • 15
Advertisement
Table of Contents
