Bosch GOP 10,8 V-LI Professional Original Instructions Manual page 8

OBJ_BUCH-775-004.book Page 8 Wednesday, February 6, 2013 9:46 AM
8 | English
Mount the requested application tool/accessory (e.g. plunge
cut saw blade 10) in such a manner on the tool holder 8 that
the offset faces downward (see illustration on the graphics
page; marking on the application tool/accessory is readable
from above).
Turn the application tool/accessory to a position favourable
for the respective job, and allow it to engage into the cams of
the tool holder 8. 12 different positions are possible, each
offset by 30°.
For more intermediate positions, the adapter 13 (accessory)
can be used: Allow the adapter to engage with the smooth
side onto the cams of the tool holder 8 (see illustration on the
graphics page). Position the application tool/accessory onto
the adapter in any position.
Fasten the application tool/accessory with bolt 11. Tighten
the bolt with Allen key 12 until the spring washer of the bolt
faces flush against the application tool/accessory.
 Check the tight seating of the application tool/acces-
sory. Incorrect or not securely fastened application tools/
accessories can come loose during operation and pose a
hazard.
Selecting the Sanding Sheet
Depending on the material to be worked and the required rate of material removal, different sanding sheets are available:
Sanding disc Material
– All wooden materials
(e.g., hardwood, soft-
wood, chipboard, build-
ing board)
– Metal materials
– Paint
– Varnish
– Filling compound
– Filler
Dust/Chip Extraction
 Dusts from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one's health. Touching or breathing-in the dusts can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dusts, such as oak or beech dust, are considered
as carcinogenic, especially in connection with wood-treat-
ment additives (chromate, wood preservative). Materials
containing asbestos may only be worked by specialists.
1 609 92A 013 | (6.2.13)
Mounting/Replacing a Sanding Sheet on the Sanding
Plate
The sanding plate 14 is fitted with Velcro backing for quick
and easy fastening of sanding sheets with Velcro adhesion.
Before attaching the sanding sheet 15, free the Velcro back-
ing of the sanding plate 14 from any debris by tapping against
it in order to enable optimum adhesion.
Position the sanding sheet 15 flush alongside one edge of the
sanding plate 14, then lay the sanding sheet onto the sanding
plate and press firmly.
To ensure optimum dust extraction, pay attention that the
punched holes in the sanding sheet match with the holes in
the sanding plate.
To remove the sanding sheet 15, grasp it at one of the tips and
pull it off from the sanding plate 14.
You can use all sanding sheets, fleece pads/polishing cloth
pads of the Delta 93 mm series of Bosch accessory program.
Sanding accessories, such as fleece pads/polishing cloth
pads, are attached to the sanding plate in the same manner.
Application
For coarse-sanding, e.g. of rough, unplaned beams and
boards
For face sanding and planing small irregularities
For finish and fine sanding of wood
For sanding off paint
For sanding primer (e.g., for removing brush dashes,
drops of paint and paint run)
For final sanding of primers before coating
– As far as possible, use a dust extraction system suitable
for the material.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
 Prevent dust accumulation at the workplace. Dusts can
easily ignite.
Grain size
coarse 40
60
medium 80
100
120
fine 180
240
320
400
coarse 40
60
medium 80
100
120
fine 180
240
320
400
Bosch Power Tools