DeWalt DS500 Mobile Lock Quick Setup & Installation Manual page 2

DS500 Quick Setup & Installation Guide
Refer to the complete DS500 instruction manual for more details.
TM
NOTE: The MOBILELOCK website and phone menu is subject to change.
3
CUSTOMIZE ALARM SETTINGS (www.dewalt.com/mobilelock or 1-410-329-9477)
1. Vibration Sensor: Select On or Off. Choose the sensitivity level and the false
alarm filter settings.
2. Door Contact Sensor: Select On or Off.
3. Temperature Sensor: Select On or Off. Select temperature threshold. Choose
between the high, low or both temperature sensors.
4. Tamper Sensor: Select On or Off.
5. Motion Detector: Select On or Off.
(Available in the DS510 combo kit only.)
6. Choose to keep the alarm on or make it silent.
4
ATTACH THE MOBILELOCK™ UNIT TO ASSET
Use the magnets on the back of the
MOBILELOCK TM unit, two #8 screws (not includ-
ed) or two bolts (not included) as appropriate
for the material to which it is affixed. To eliminate
false alarms, be sure that the MOBILELOCK
unit is secure or hidden so it is not removed.
If using the door contact sensor, place the mag-
net on the door jam no more than 3/8" (9.5 mm)
from the magnet icon on the left side of the
MOBILELOCK TM unit (mounted on the door).
NOTE: Please refer to the instruction manual for
detailed instructions for mounting
TM
MOBILELOCK accessories.
5
TEST THE SYSTEM
To test the system, go to www.dewalt.com/mobilelock or call the phone menu system
1-410-329-9477 and select Status Update followed by System Test from the Unit
Customization menu.
TM
The MOBILELOCK system test will cycle through all the ACTIVE sensors in the
following order: vibration, door contact, motion, and tamper. As you trip each sensor,
TM
the MOBILELOCK unit will sound an alarm. Wait for the siren to complete before trip-
ping the next sensor. A cellular notification will not be sent. Continue tripping sensors
until the test is complete. The test will automatically time out after 5 minutes or when
each of the sensors has been tripped.
BASIC OPERATIONS
NOTE: The MOBILELOCK TM website and phone menu is subject to change.
ARMING, DISARMING AND LOCATING
Refer to the instruction manual for details on setting up an Arm and Disarm schedule.
TM
3/8" (9.5 mm)
other
2
Arm and Disarm
1. Go to www.dewalt.com/mobilelock or call 1-410-329-9477. Login with pass-
word.
2. Select Arm or Disarm.
Wait for confirmation that the unit has been armed.
NOTE: If you have chosen to activate the arm and disarm confirmation chirps, the
TM
MOBILELOCK unit will beep once to indicate the unit is armed, twice to indicate the
unit is disarmed.
Assisted GPS Locate
1. Go to www.dewalt.com/mobilelock. Login with password.
2. Select Locate.
The amount of time to receive the location will vary. In most cases, the location is
provided in about one minute. Click Location (view) to be linked to the map.
Guía de instalación y confi guración rápida del DS500
Consulte el manual de instrucciones completo del DS500 para obtener más detalles.
NOTA: El sitio Web y el menú telefónico de MOBILELOCK
caciones.
3
CONFIGURACIONES PERSONALIZADAS DE LA ALARMA
(www.dewalt.com/mobilelock o 1-410-329-9477)
1. Sensor de vibración: Seleccione Encendido (On) o Apagado (Off). Elija las
configuraciones del nivel de sensibilidad y el filtro de falsas alarmas.
2. Sensor de contacto para puertas: Seleccione Encendido (On) o Apagado
(Off).
3. Sensor de temperatura: Seleccione Encendido (On) o Apagado (Off).
Seleccione el umbral de temperatura. Elija el sensor de temperatura alta, el de
temperatura baja o ambos.
4. Sensor de intento de forzamiento: Seleccione Encendido (On) o Apagado
(Off).
5. Detector de movimiento: Seleccione Encendido (On) o Apagado (Off).
(Disponible sólo en el juego combinado DS510.)
6. Elija mantener la alarma encendida o en silencio.
4 CONEXIÓN DE LA UNIDAD MOBILELOCK™
AL BIEN A PROTEGER
Utilice los imanes que se encuentran en la parte
posterior de la unidad MOBILELOCK
tornillos nº 8 (no incluidos) o dos pernos (no
incluidos) apropiados para el material sobre
el cual deba instalar la unidad. Para eliminar
falsas alarmas, asegúrese de que la unidad
MOBILELOCK TM esté segura u oculta de
manera que no se pueda quitar.
TM están sujetos a modifi-
TM
, dos
9,5 mm (3/8")
3