Ariens Compact 24 LE Quick Start Manual
  1. Manuals
  2. Brands
  3. Ariens Manuals
  4. Snow Blower
  5. Compact 24 LE
  6. Quick start manual
Ariens Compact 24 LE Quick Start Manual

Ariens Compact 24 LE Quick Start Manual

Hide thumbs Also See for Compact 24 LE:
Table of Contents

Advertisement

Quick Links

See also: Service Manual , Manual
Compact 24 LE (920014 s/n 100000 & up)
•
Step 1: Assemble Handlebar
•
Step 2: Install Discharge Chute
•
Step 3: Install Discharge Chute Crank
•
Step 4: Install Remote Deflector Cable
•
Step 5: Check Function of Dual Handle Interlock
•
Step 6: Check Tire Pressure
•
Step 7: Adjust Skid Shoes
•
Step 8: Check Auger Gearcase Oil
•
Step 9: Check Engine Crankcase Oil
•
Step 10: Fill Engine Fuel Tank
•
Step 11: Starting the Engine
•
Step 12: Stopping the Engine
READ AND UNDERSTAND ALL INSTRUCTION, WARNING, AND DANGER LABELS.
IMPORTANT: READ OPERATOR'S MANUAL AND ENGINE MANUAL
THOROUGHLY AND FOLLOW THE IMPORTANT SAFE OPERATION PRACTICES
BEFORE OPERATING.
Quick Start Guide

Advertisement

Table of Contents
loading

Related Manuals for Ariens Compact 24 LE

Summary of Contents for Ariens Compact 24 LE

  • Page 1 Quick Start Guide Compact 24 LE (920014 s/n 100000 & up) • Step 1: Assemble Handlebar • Step 2: Install Discharge Chute • Step 3: Install Discharge Chute Crank • Step 4: Install Remote Deflector Cable • Step 5: Check Function of Dual Handle Interlock •...
  • Page 2 Step One: Assemble Handlebars NOTE: The Ariens company has made changes to packaging that affects this serial number range. If the upper handlebars on your unit came already attached please disregard the following five slides. Not attached Attached...
  • Page 3 Step One: Assemble Handlebars NOTE: This slide applies to UNATTACHED handlebars ONLY (Unfold Lower Handlebar) Remove wheel pins from each side of the unit and slide wheels away from frame. Do not remove wheels completely. IMPORTANT: Be sure to block wheels or secure unit so it does not move during assembly.
  • Page 4 Step One: Assemble Handlebars NOTE: This slide applies to UNATTACHED handlebars ONLY (Attach Upper Handlebar Assembly) Attach upper handlebar assembly to lower handlebar using two sets of the handlebar hardware. One set to attach each side of the handlebars. NOTE: DO NOT tighten hardware. Allow upper handlebar assembly to hang from the lower handlebars for the next step.
  • Page 5 Step One: Assemble Handlebars NOTE: This slide applies to UNATTACHED handlebars ONLY (Attach Control Cables) Hook Spring end of attachment control cable to the clutch arm. Hook spring end of the traction control cable to the cable eyelet on back of frame. NOTE: Make sure cable remains in groove of pulley.
  • Page 6 Step One: Assemble Handlebars NOTE: This slide applies to UNATTACHED handlebars ONLY (Unfold Upper Handlebar) Assembly) Rotate handlebar into operating position. NOTE: Be careful not to damage cable spring hooks when rotating handlebar upward. Install the remaining handlebar hardware attaching the upper handlebar assembly to the lower handlebar.
  • Page 7 NOTE: This slide applies to Step One: UNATTACHED handlebars ONLY (Connect Headlight Wire Harness) NOTE: The headlight wire harness comes attached to the upper handlebar assembly. Route the wire harness along the interior of the right side handlebar. Connect to the engine electrical plug. Press cable anchor into mounting hole in the frame near the engine electrical plug.
  • Page 8 Step One: NOTE: This slide applies to ATTACHED handlebars ONLY Assemble Handlebar Remove the lower and loosen the upper hardware on the handlebar assembly. Loosen the hardware on the shift rod. Put the speed selector lever in the sixth forward position. Rotate the handlebar into operating position.

  • Page 9: Install Discharge Chute

    Step Two: Install Discharge Chute Grease underside of discharge chute ring (if not already greased). Remove mounting hardware from auger housing Install discharge chute over opening in the auger housing. Finger tighten the mounting hardware removed above. NOTE: Leave discharge chute pedestal loose to help install the chute crank.

  • Page 10: Discharge Chute Crank

    Step Three: Install Discharge Chute Crank Remove gear cover from top of chute pedestal. Slide Chute Crank through the nylon bushing in the support bracket under control panel. NOTE: Be careful not to damage nylon bushing when attaching crank to the control panel. Connect the chute crank to the pinion gear on discharge chute with spring clip pin.
  • Page 11 Step Four: Install Remote Deflector Cable Pull rubber seal cap away from snap fitting. Install snap fitting into cable bracket’s mounting hole located under the dash. Position rubber seal cap over the top of snap fitting. Move deflector control lever to forward most position. Attach cable eye to pin on bottom of deflector control lever.
  • Page 12 Step Four: Install Remote Deflector Cable Cont. Secure cable eye to control lever with sleeve bushing and hairpin. Using the wire hook attached to the deflector cable, hook cable to discharge chute crank. Install cable into clip on top of discharge chute pedestal. Make sure deflector cable loops above gear cover between cable clip and cable support bracket.
  • Page 13 Step Five: Check Function of Dual Handle Interlock Without the engine running, press down (engage) both clutch levers. Release attachment clutch lever. Attachment clutch should remain engaged until traction clutch lever is released, then both clutches must disengage. If they do not, contact your dealer for repairs.
  • Page 14 Step Six: Check Tire Pressure Check tire pressure and adjust to the pressure listed on tire sidewall.
  • Page 15 Step Seven: Adjust Skid Shoes IMPORTANT: Skid shoes should be adjusted as conditions require. Allow 1/8 in. (3mm) between scraper blade and hard smooth surfaces. Allow 7/8 in (22 mm) between scraper blade and uneven or gravel surfaces. (See Skid Shoes in Owners Manual).
  • Page 16 Step Eight: Check Auger Gearcase Oil Check oil level in auger gearcase (see Check Auger Gearcase in Owners Manual).
  • Page 17 Step Nine: Check Engine Crankcase Oil IMPORTANT: The engine is shipped with oil in crankcase. Refer to Engine Manual for detailed instructions.
  • Page 18 Step Ten: Fill Engine Fuel Tank Fill fuel tank. DO NOT OVERFILL! See FILLING FUEL TANK in Owners Manual. Remove the plug from the fuel tank and install the fuel cap located in the attached bag.
  • Page 19 Step Eleven: Starting the Engine...
  • Page 20 Starting Engine / Step A: Throttle Move the throttle control lever to the fast position. Operate the engine with the throttle control lever in the fast position.

  • Page 21: Starting Engine / Step B: Fuel Valve

    Starting Engine / Step B: Fuel Valve Turn the fuel shut- off valve to the “ON” position.

  • Page 22: Starting Engine / Step C: Key

    Starting Engine / Step C: Insert the key and turn to the on/start position.

  • Page 23: Starting Engine / Step D: Choke

    Starting Engine / Step D: Choke Turn the choke control knob to the choke position. NOTE: Choke is usually unnecessary when restarting a warm engine.

  • Page 24: Starting Engine / Step E: Prime

    Starting Engine / Step E: Prime Push the primer two times. Be sure to cover the vent hole on the primer bulb. NOTE: Priming is usually unnecessary when restarting a warm engine.

  • Page 25: Starting Engine / Step F: (Manual Start)

    Starting Engine / Step F: (Manual Start) Firmly hold the starter cord handle. Pull the starter cord handle slowly until resistance is felt, then pull rapidly. NOTE: If the engine does not start after repeated attempts, go BRIGGSandSTRATTON.COM or call 1-800-233-3723.

  • Page 26: Starting Engine / Step F: (Electric Start)

    Starting Engine / Step F: (Electric Start) First connect the extension cord to the power cord receptacle and then into a wall receptacle. If an additional extension cord is required, make sure it is a 3-wire grounded extension cord.

  • Page 27: Starting Engine / Step G: (Electric Start)

    Starting Engine / Step G: (Electric Start) Depress the push button. After you start the engine, first disconnect the extension cord from the wall receptacle and then from the power cord receptacle.

  • Page 28: Starting Engine / Step H: Warm Up

    Starting Engine / Step H: Warm up Allow the engine to warm up for several minutes. Then, slowly move the choke control knob to the run position.
  • Page 29 Step Twelve: Stopping the Engine Turn the key to the off position or move throttle control lever to slow and then to the stop position (completely left). Remove the key. Keep away from reach of children. After engine stops, turn the fuel shut-off valve to the closed (vertical) position.

  • Page 30: Additional Resources

    Additional Resources • Refer to Owners Manual and Engine Manual • Contact Ariens Company www.ariens.com Phone: 920-756-4688 E-mail: info@ariens.com • For issues concerning engine, please contact Briggs and Stratton www.BRIGGSandSTRATTON.com Phone: 800-233-3723 2012 The Ariens Company. All rights reserved.

This manual is also suitable for:

920014

Table of Contents