Table of Contents
Advertisement
PRE-INSTALLATION STEPS
Bottom
Bustle
Unit Parts Identification
Figure 7 - Unit Parts Identification
The appliance is shipped with all gas controls
and components installed and pre-wired.
1. Remove the shipping carton.
2. Remove the top radiant panel (refer to
Figure 7).
3. Open the control compartment access panel,
by actuating the spring-loaded magnetic
catches securing the panel, gently depress-
ing the outer top corners of the panel until
the catches "pop" the panel free and allowing
it to swing out and down to open.
4. Remove the bottom control compart-
ment access panel by compressing the
spring-loaded hinge pin on the left side
until it disengages from the left cabinet
panel hole. Pull the panel away from the
fireplace.
5. Remove the modesty panel by pulling the
bottom right corner of the modesty panel
out slightly to disengage the snap-fit fea-
ture; lift the modesty panel by the tab on
the panel's right end, pull the right end of
the panel away from the cabinet and then
pull the panel diagonally out of the left side
cabinet panel slots. Remove the modesty
panel carefully, so that none of the wires
become loose or disconnected.
6. Open the latch (located under the firebox
floor) securing the glass enclosure panel.
Remove the panel by tilting it outward at
the bottom and lifting it up. Set the door
aside protecting it from inadvertent damage.
See Figure 29 on Page 20.
7. Remove log set box from firebox. Next,
remove embers, vermiculite and volcanic
stone from control compartment. Handle
logs carefully to prevent breakage.
8
TYPICAL INSTALLATION SEQUENCE
The typical sequence of installation is outlined
Top Radiant
below. However, each installation is unique
Panel
and may result in variations to the steps
described.
Top Bustle
See the page numbers references in the follow-
Control
Compartment
ing steps for detailed procedures.
Access Panel
Step 1. (Page 9) Construct the appliance
framing. Position the appliance within the
framing and secure with nailing brackets and
floor anchor tabs.
Step 2. (Page 11) Route gas supply line to
appliance location.
Step 3. (Page 11) Install the vent system and
exterior termination.
Step 4. (Page 12) Field Wiring
a. Millivolt Appliances – The operating control
switch is factory installed.
b. Electronic Appliances – Connect 120 VAC
electrical power to the appliance receptacle.
(EDVPF - NO NAILING FLANGES
ON END WITH GLASS PANEL)
Nailing
Nailing Flanges
Flanges
Turn tabs down and secure to the floor with
8d nails or other appropriate fasteners
on all sides of the unit which do not have
viewing glass panels.
Figure 8 - Nailing Flanges
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
EDVST SHOWN
EBVST SHOWN
(EBVPF - NO NAILING FLANGES ON END WITH GLASS PANEL)
Remove these two screws and
use them when installing
the nailing flanges.
Turn tabs down and secure to the floor with
8d nails or other appropriate fasteners on all sides
of the unit which do not have viewing glass panels.
Step 5. (Page 14) Make connection to gas
supply.
Step 6. (Page 15) Install and verify outside
air kit operation.
Step 7. (Page 16) Checkout appliance opera-
tion.
Step 8. (Page 17) Install the log set, vermicu-
lite, volcanic stone and glowing embers.
Step 9. (Page 20) Removing and Installing
glass enclosure panels.
Step 10. (Page 20) Adjust burner primary air
shutter to achieve proper flame appearance.
Step 11. (Page 21) Install the hoods.
Step 12. (Page 22) Conduct limit switch
spillage test.
Step 13. (Page 23) Attach safety in operation
warnings.
EDVCL SHOWN
(FOR EDVCR VIEW, INTERCHANGE SIDES)
Remove these two screws and
use them when installing
the nailing flanges.
Hide quick links:
Advertisement
Table of Contents
