Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty. If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so and refer the repair to a qualified service technician. DEH-MG8137ZT/UC...
FM/AM TUNER UNIT ANTENNA JACK Detailed page FM:-27dBs AM:-28dBs FM:-27dBs (400Hz,30% mod) CD: 0dBs AVC-LAN: 0dBs DIGITAL SOUND P SOURCE SEL ELECTRIC VO AM:-12.7dBs AM PNS AM:-13.2dBs FM: - AM:-9 CD: + AVC-LAN: + SYSTEM CONTROLLER CD:+0.1dBs (1kHz,0dB) CN902 DEH-MG8137ZT/UC...
Page 17
No differentiation is made between chip capacitors and 0.022 R022 discrete capacitors. The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. DEH-MG8137ZT/UC...
CRG MOTOR M3 CXC1143 RF AM MP3 DE DIGITA PROCE CN41 CN14 CN31 PU UNIT(SERVICE)(PX1MP3) ELEVATION MOTOR M2 CXC1145 CAMEOK PCB UNIT CAMLOAD (LED) LOAD1 LOAD2 PCB UNIT CN13 (LOAD) M1 CXC1144 3+3ch DRIVER C D E F G H DEH-MG8137ZT/UC...
Page 25
SIGNAL LINE FOCUS SERVO LINE TRACKING SERVO LINE CARRIAGE SERVO LINE SPINDLE SERVO LINE RF AMP, CD DECODER, MP3 DECODER, DIGITAL SERVO/ DATA PROCESSOR CONTROL UNIT(G2MP3T) MECHANISM CONTROLLER Not used DEH-MG8137ZT/UC...
For further information for respective destinations, be sure to check with the schematic dia- gram. CAR HARNESS CAR HARNESS 2.Viewpoint of PCB diagrams Capacitor Connector SIDE A SIDE B P.C.Board Chip Part CN901 DEH-MG8137ZT/UC...
Page 33
SIDE A CAR HARNESS ANTENNA MAIN CN902 FRONT DEH-MG8137ZT/UC...
Page 51
Unit Number : CWX2611 Unit Name : PCB Unit Inductor CTF1389 Spring Switch(LOAD3) CSN1051 Unit Number : CWX2613 Unit Name : PCB Unit(Side) MISCELLANEOUS Spring Switch(CAMCLMP) CSN1052 Semi-fixed 1kΩ(B) CCP1338 RESISTORS RS1/16S562J RS1/16S562J RS1/10S391J RS1/10S391J RS1/16S0R0J RS1/16S0R0J CAPACITORS CKSRYB104K25 DEH-MG8137ZT/UC...
6. ADJUSTMENT 6.1 CONNECTION DIAGRAM GGF-146 Power supply cable Head unit DEH-MG8137ZT/UC 12P AVC-LAN cable 82372-AA010(HDE0058 or HDE0060) XM tuner GEX-M8087XMZT/XN/UC XM antenna unit AN-90XM or TOYOTA model DEH-MG8137ZT/UC...
*1) Note that the test mode is cancelled in the system microcomputer by switching the ACC OFF and ON, but that it is not in the CD microcomputer. Use the reset function for complete cancellation of the test mode. DEH-MG8137ZT/UC...
• If you press the UP or DOWN for the focus search in the test mode, you must turn the power off immedi- ately. (Otherwise, the lens will be forced to stick to the top or bottom, potentially resulting in the burning of the actuator.) DEH-MG8137ZT/UC...
Page 55
Single TR (91),0dB, and the factory setting respectively. Note: When you pressed the [TUNE UP] or [TUNE DOWN] key during the Focus Search, you must turn the power off immediately (otherwise, the lens can stick resulting in actuator damages). DEH-MG8137ZT/UC...
Because of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may be seen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the aver- age angle. • Hint Reloading the disc changes the clamp position and may decrease the "wobble". DEH-MG8137ZT/UC...
3. LIFT durability test (Current disc <-> Door Open) At any position between CAM2P and CAM3P (display: 05, 07), press the 5 key. 4. ELV durability test (ELV1F <-> 6F) At the CAM1P position (display: 01), press the 5 key. DEH-MG8137ZT/UC...
Page 59
MFWDTO ELV motor FWD time-out error during CAMRST operation CAMRST Err 0x91 0x92 MREVTO ELV motor REV time-out error during CAMRST operation MOVERCNT 0x93 Over-count error during CAMRST operation 0x94 MSPDERR The claws do not close during CAMRST operation. DEH-MG8137ZT/UC...
Page 60
Lock NG after servo close New test mode 0x42 Sub code NG after servo close 0x43 New test mode Not applicable to the G2 mechanism. The claw SW value at the occurrence of error The rotation rate does not satisfy the spec. DEH-MG8137ZT/UC...
Page 61
DSKFREE: Claw's closing motion to release the clamped disc DSKLOCK: Claw's opening motion to clamp a disc CLWCLSE: Claw's closing motion CLWOPEN: Claw's opening motion DISCSEL: Elevation motion FEJCHK: Mechanical motion to check that there is no disc around the loading slot DEH-MG8137ZT/UC...
Release the two latches and then remove the Grille Assy. Fig.1 Removing the Chassis (Fig.2) Heat Sink Remove the two screws. Remove the three screws and then remove the Heat Sink. Remove the five screws and then remove the Chassis. Chassis Fig.2 DEH-MG8137ZT/UC...
Page 67
Removing the Main Unit (Fig.3) Disconnect the connector. Straighten the tabs at five locations indicated. Remove the two screws and then remove the Main Unit. Main Unit Fig.3 DEH-MG8137ZT/UC...
Page 68
3. Remove the four Dampers and then remove the Mechanism Unit(G2TMP3). Case Shorting solder Spring B Mechanism Unit(G2TMP3) Damper Sheet Spring A Damper Sheet Spring B Bracket Unit Control Unit Sheet (G2MP3T) Spring A Damper Screw A Screw A Sheet Screw B Damper Screw B Fig.4 DEH-MG8137ZT/UC...
Page 69
PCB Unit(Side) GGD1250 Control Unit(G2TMP3) - Removing the PU Unit(PX1MP3) 1. Set the mechanism to the shipment mode. 2. Remove the two screws A and two screws B. 3. Remove the Frame. Fig.5 DEH-MG8137ZT/UC...
Page 70
PU Unit(PX1MP3) together with the Screw Unit. Note: To assemble the PU Unit(PX1MP3), insert the Spring on the PU rear between the PU Unit(PX1MP3) and (PX1MP3) the Guide first. Fig.8 DEH-MG8137ZT/UC...
AM power supply control output LANMUTE AVC-LAN mute input IPPW IP-BUS : Power supply control output for IP BUS interface IC ADIN ADIM signal output SYSPW System power supply control output Not used FANPW Not used KEYILL Key illumination control output DEH-MG8137ZT/UC...
Page 73
A/D converter reference voltage AVCC Analog power supply Tuner : Data input * PD5860A IC's marked by * are MOS type. Be careful in handling them because they are very liable to be damaged by electrostatic induction. * S-80835CNNB-B8U DEH-MG8137ZT/UC...
Page 76
AVSS Ground (Analog) Analog power supply terminal CAP1P External capacitor connect terminal CAP1N External capacitor connect terminal DC_OUT DC/DC converter output Bout Blue output Gout Green output Rout Red output PVSS DC/DC converter ground BU8770AFV * S-812C56AUA-C3K Reference Voltage DEH-MG8137ZT/UC...
Page 77
Information on error correction (mute for Lch) C2D3 Information on error correction D.GND Ground for digital circuits Output of DRAM RAS cas) Output of DRAM Lower CAS cas! Output of DRAM Upper CAS Output of DRAM WE Output of DRAM OE DEH-MG8137ZT/UC...
Page 78
Output of TE A.GND Ground for the analog system LDREGO Output of REG voltage for APC Input of PD Output of LD Assignment of pickup polarity A.VDD Power supply for the analog system * UPD63760GJ * S-812C33AUA-C2N Reference Voltage DEH-MG8137ZT/UC...
Page 79
: Output enable input : Write enable input lcas : Power supply(3.3V) ucas : Ground(0V) SHORT BRAKE 30 A7 26 VSS Hall Bias Hall Bias Hall Bias Hall Bias Hall Bias Hall Bias BD7962FM LEVEL SHIFT LEVEL SHIFT LEVEL SHIFT LEVEL SHIFT DEH-MG8137ZT/UC...
Page 80
Address/Data bus 8-15 Not used Not used MEMO1 Shock proof memory buffer output 1 MEMO0 Shock proof memory buffer output 0 CD LSI chip select output Not used AVDD A power supply Positive power supply (5V) AVSS A power supply GND DEH-MG8137ZT/UC...
Page 81
LOD drive voltage select output E2PROM data input/output E2PROM chip selection output SCKO E2PROM clock output FRXD For flash rewriting (received signal) FTXD For flash rewriting (transmitted signal) BUFEMP Not used P-Bus serial data input * PE5371A Format Meaning CMOS DEH-MG8137ZT/UC...
Page 82
Connect to the antenna through an L (LAU type) of 4.7µH.To cope with the power transmission line hums, insert a series circuit consisting of an L (a coil of about 100mH) + R (a resistor of 470 Ω to 2.2kΩ) between the GND. DEH-MG8137ZT/UC...
After disconnecting the power supply connector and removing this product, confirm that you can see a metal plate through the hole near the "SHIP" mark on the rear chassis. Confirm that the door of the CD player is closed. DEH-MG8137ZT/UC...
MUTE button. with Passion. will flash on and off. • Press the COLOR CHANGE To cancel this mode, press the MUTE button in the Mixer mode, button again. and you can change the color in order starting with Ice Blue. DEH-MG8137ZT/UC...
Press to recall previously memorized stations (Preset Channels). Press and hold until you hear a beep, and the station you are currently tuned to is memorized as a Preset Channel. NOTICE You can store up to 6 stations per band. DEH-MG8137ZT/UC...
If you press and hold until you hear a side the unit. Be sure to oper- beep, is indicated in the dis- ate the player correctly. play and starts to play the first 10 DEH-MG8137ZT/UC...
Page 90
A maximum of 2 pages (24 characters) title can be displayed. While this is pressed, play of the track is reversed. (There is no sound.) 8 PRESET 6 (¡) While this is pressed, play of the track is fast forwarded. (There is no sound.) DEH-MG8137ZT/UC...
Page 91
NOTICE Preset Channel. About the display Up to a maximum of 10 alphanu- NOTICE meric characters can be displayed. (Some information will not be You can store up to 6 chan- fully displayed.) nels per band. DEH-MG8137ZT/UC...