Related Manuals for Planet ICA-HM830
Summary of Contents for Planet ICA-HM830
- Page 1 2 Mega-Pixel Fish-Eye Panorama Outdoor / Indoor IP Camera ICA-HM830 / ICA-HM830W ICA-HM835 Quick Installation Guide...
-
Page 2: Table Of Contents
1.1 Before Installation ................3 1.2 System Requirements ................3 Chapter 2. Physical Description and Installation ..........4 2.1 ICA-HM830 2Mega-Pixel Fish-Eye Panorama IP Camera ......4 2.1.1 ICA-HM830 Package Content ............4 2.1.2 ICA-HM830 Physical Details ............4 2.1.3 ICA-HM830 Installation ..............6 2.1.4 Wall/Ceiling Mount Installation Procedure ........ -
Page 3: Chapter 1. Introduction
2-Way audio that enables audio communication between local and remote IP Camera installed sites by connecting the external microphone and speaker. Moreover, the IP camera can be managed by PLANET Cam Viewer 3 IP- Surveillance management software for multi-camera video surveillance application and provides monitoring, recording and event management functions to secure your property and life. -
Page 4: Chapter 2. Physical Description And Installation
Chapter 2. Physical Description and Installation 2.1 ICA-HM830 2Mega-Pixel Fish-Eye Panorama IP Camera 2.1.1 ICA-HM830 Package Content IP camera unit x 1 Power Adapter x 1 Quick Installation Guide x 1 User’s manual CD x 1 Wall Mount Kit x 1 GPIO Connector x 1 2.1.2 ICA-HM830 Physical Details... -
Page 5: Interface Description
ICA-HM830 Bottom Panel: DC 12V Audio Out RJ-45 Audio In MICRO SD GPIO Interface Description The input power is DC 12V, 2A. Power Jack Note: ONLY use package power adapter supplied with the internet. Otherwise, the product may be damaged. -
Page 6: Ica-Hm830 Installation
Photo-coupled relay on Normal Open status. External device can directly connect to the terminals. However the current that will go through the 2 nodes must not exceed 130mA. An external “Relay” can also be connected to the terminals as an implementation. In this case, current (or/ DO_COM and voltage) limitation is specified by the external Relay. 2.1.3 ICA-HM830 Installation... -
Page 7: Wall/Ceiling Mount Installation Procedure
Step 1. Prepare a PC with Ethernet link to the network Step 2. Connect an Ethernet cable Connect LAN port (RJ-45) of the IP Camera to a network switch. When this switch is a PoE device, you can ignore the next step. If there has an IEEE 802.3af PoE switch in your network, you can connect the IP Camera’s LAN cable to this PoE switch to obtain power. -
Page 8: Ica-Hm830W 2Mega-Pixel Fish-Eye Panorama Ip Camera
Step 2. Load the camera into the wall mount, be sure the camera is mated with two fixed screw, and rotate the camera to lock it in position. 2.2 ICA-HM830W 2Mega-Pixel Fish-Eye Panorama IP Camera 2.2.1 ICA-HM830W Package Content IP camera unit x 1 Power Adapter x 1 Quick Installation Guide x 1 User’s manual CD x 1 Wall Mount Kit x 1 GPIO Connector x 1... -
Page 9: Ica-Hm830W Physical Details
2.2.2 ICA-HM830W Physical Details ICA-HM830W Front Panel: Light Sensor Reset Button Speaker Interface Description The Light sensor is for detect IP Camera environment Light Sensor illuminant, and if IP Camera in the dark/night environment that will let IR cut filter off for clearly night view. The IP Camera has built-in an internal microphone. This microphone is hidden in the pinhole located on the front panel. - Page 10 ICA-HM830W Bottom Panel: DC 12V Audio Out RJ-45 Audio In MICRO SD GPIO Interface Description The input power is DC 12V,2A. Power Jack Note: ONLY use package power adapter supplied with the internet. Otherwise, the product may be damaged. Connect to PC or Hub/Switch. For connect to 10Base-T Ethernet or 100Base-TX Fast Ethernet cabling.
-
Page 11: Ica-Hm830W Installation
Terminal block for I/O connectors: Name Function Four sets of Digital Input, DI1 until DI4; the internal Digital input 4 device is also photo-coupled electrical relay. In practice, Digital input 3 the external device can be simply an On/Off switch. Four sets of On/Off switch can be connected as different Digital input 2 trigger source. -
Page 12: Wall/Ceiling Mount Installation Procedure
Step 1. Prepare a PC with Ethernet link to the network Step 2. Connect an Ethernet cable Connect LAN port (RJ-45) of the IP Camera to a network switch. Step 3. Attach the power supply Plug in power adapter to IP Camera and connect another end to power outlet. -
Page 13: Ica-Hm835 2Mega-Pixel Vandal Proof Fish-Eye Ip Camera
Step 2. Load the camera into the wall mount, be sure the camera is mated with two fixed screw, and rotate the camera to lock it in position. 2.3 ICA-HM835 2Mega-Pixel Vandal Proof Fish-Eye IP Camera 2.3.1 ICA-HM835 Package Content IP camera unit x 1 Power Adapter x 1 Quick Installation Guide x 1 User’s manual CD x 1 Screw Package x 1 GPIO Connector x 1... - Page 14 Interface Description The input power is DC 12V, 2A. Power Jack Note: ONLY use package power adapter supplied with the internet. Otherwise, the product may be damaged. Connect to PC or Hub/Switch. For connect to 10Base-T Ethernet or 100Base-TX Fast Ethernet cabling.
-
Page 15: Ica-Hm835 Installation
2.3.3 ICA-HM835 Installation Step 1: Prepare a PC with Ethernet link to the network Step 2: Connect an Ethernet cable Connect LAN port (RJ-45) of the IP Camera to a network switch. When this switch is a PoE device, you can ignore the next step. If there has an IEEE 802.3af PoE switch in your network, you can connect the IP Camera’s LAN cable to this PoE switch to obtain power. -
Page 16: Chapter 3. Camera Windows Utility
This chapter shows how to quick set up your IP Camera. The IP Camera is with the default settings. However to help you find the networked IP Camera quickly the Windows utility (PLANET IPInstaller) can search the IP Cameras in the network that shall help you to configure some basic setting before you start advanced management and monitoring. - Page 17 3. Double click the item to open the Property Page or click the menu bar View > Property. 4. After filling the desired settings in the properties, click on “Set” button to complete the configuration settings.
-
Page 18: Open The Web-Based Ui
3.2 Open the Web-based UI If IPInstaller finds IP Camera, please select the device you want to view and click the “Open Web” button. Then you could see the video from IP Camera directly. 1. To access the Web-based UI of the selected unit, run the View > Open Web on the menu bar. - Page 19 3. For the first installaiton, there will be a prompt to install the ActiveX control. 4. If the device has been configured correctly, the default Web browser will open to the home page of the selected device.
-
Page 20: Further Information
Further Information This guide is used to help you startup your Fish-Eye IP Camera settings. It is also recommended to check the user manual in CD disk for more details of the system and user configuration.