Utilitech TM-074 Operating Instructions

ITEM #0149289 3. Set Current Time
3
MODEL #TM-074
a. Press and hold "TIME"
MO
TIMER button to enter the
current time until the MO
flash. First, set the day
Call customer service at 1-866-994-4148,
of the week; press "+" or
8 a.m. - 6 p.m., EST, Monday - Thursday,
"-" button to set the
8 a.m. - 5 p.m., EST, Friday.
correct day.
OPERATING INSTRUCTIONS b. Press the "TIME" button to enter the hour setting.
Press "+" or "-" buttons to set the current hour. Be
Before initial use, plug the timer in for at least 30
sure that AM or PM appears correctly.
minutes to charge the internal battery. After the screen c. Press the "TIME" button to enter the minute
displays, the unit is ready for programming.
setting. Press the "+" or "-" buttons to set the
current minute.
The device must be mounted in a vertical position with
d. Press the "TIME" button to finish setting the
the receptacle facing downward and with the
current time and return to normal display.
receptacle at least 1.4 m above ground level.
4. MODE Setting
1. Button Layout
1
Press MANU button repeatedly to choose the AUTO
1. MANU - Manual Override,
mode, then press MODE button to choose between
scroll between timer
1 2 3 function: Timer→ Photocell→Timer + Photocell→
status options.
Timer (repeat)
4 6
2. TIME - Press and hold for
three seconds to set 5
The below icons will appear
4
current time.
on the right of display.
7
3. PROG - Press and hold
MO
for three seconds to begin setting function.
AUTO
4. < + > - To increase time and day setting.
5. MODE - Press and hold the "MODE" button to
scroll between the different mode settings as the
following table describes.
6. < - > - To reduce time and day setting.
7. RESET - Reset all the functions.
Display MODE Explanation
ON/OFF at your exact
2. Reset
2
Timer programmed time. (Please refer
to Step 5 for details.)
Press the "RESET" button to
RDM MO TU WE TH FR SA SU
reset your timer. This will ON at dusk or ON immediately;
AUTO
Photocell OFF after 1-12 hours. (Please
clear all programmed
ON AM
OFF
PM refer to Step 6 for details.)
settings.
ON at dusk, OFF at your exact
Timer
+ programmed timer. (Please refer
Photocell
to Step 7 for details.)
Note: You can choose each mode or combined modes
to control your lights.
AB13568
Page 1
5. Timer Setting (Program settings, the display appears 1. Set the desired day of the week program by
icon on the right side.) pressing the "+" or "-" button, you can select:
MO TU WE TH FR SA SU(Everyday)→MO TU
Before setting, make sure timer is set to AUTO or
WE TH SA SU→MO TU WE TH FR(Monday to
RDM mode. Friday) → SA SU(Weekend)→MO TU WE TH FR
AM
SA SU (repeat).
Press and hold "PROG" 2. Press "MANU" to enter the hour settings, press
5
button for three seconds
"+" or "-" to set:
until the days of the week
MO TU WE TH FR SA SU Display Explanation
flash to begin program
setting. Dusk to Dawn - On at sundown, off at
ON
d
sunrise.
d:01 to d:12 On at dusk, off 1 to 12 hours later
S:01 to S:12 On immediately, off 1 to 12 hours later
1. Set the desired day of the week by pressing "+" or
"-" button: MO TU WE TH FR SA SU→ MO... SU a. When screen shows "d" the Dusk on/Dawn off
→MO TU WE TH FR→SA SU→MO TU WE TH function is on.
FR SA SU (repeat) b. When screen shows "d:01", press MANU
button, then press "+" or "-" button to choose
2. After setting the date, please press the MANU
button to adjust the hours. your desired hours to be off at dusk after the
3. After setting the hours, press the MANU button set hours automaticity. For example, if you set
again to adjust the minutes. it to be "d:03", the timer will turn on at dusk and
4. Press PROG button to enter the program OFF will turn off after 3 hours.
c. When screen shows "S:01", press MANU
setting, the 1 OFF will appear on the display.
Repeat steps 1 to 3 above to set your desired button, then press "+" or "-" button to choose
OFF time. your desired hours to be off automatically. For
5. You may now either press the PROG button to example, if you set it to be "S:05", the timer will
enter additional programs (up to 8 programs), or turn on immediately and will turn off after 5
hours.
press the TIME button (or wait 15 seconds) to
AM
store your program. Your timer will now show the d. You may now either press the PROG button to
current set time and is ready for use. enter additional programs (up to 8 programs),
or press the TIME button (or wait 15 seconds)
to store your program. Your timer will now
6. Photocell Setting
show the current set time and is ready for use.
Before setting, make sure timer is set to AUTO
NOTE: Once all programs have been set, the
mode.
priority goes to the longest time set.
Press "MODE" button to
6
select the photocell function 7. Digital Timer + Photocell Setting
(the display will show the
MO TU WE TH FR SA SU
icon on the right side),
Before setting, make sure timer is set to AUTO
then press and hold mode.
ON
"PROG" button for three
seconds until the days of
the week flash to begin
program setting.
Press "MODE" button to HELPFUL TIPS
7
select the timer + photocell
• Do not attach a device that exceeds the unit ratings
function (the display will
as described in the Safety Information section of this
appear the icon on MO TU WE TH FR SA SU
manual.
the right side.), then press
and hold "PROG" button for OFF
three seconds until the
days of the week flash to
SAFETY INFORMATION
begin program setting.
Please read and understand this entire manual before
1. Set the desired day of the week program by
attempting to assemble, operate or install the product.
pressing the "+" or "-" button. You can select
each day individually, Monday to Friday,
SPECIFICATIONS:
Saturday/Sunday, or an entire week to have your
14/3 AWG SJTW vinyl cord
timer turn on at dusk and off at the set time.
RATINGS:
2. Press the "MANU" button to enter the "OFF" time
125 V, 60 Hz, 15 A general purpose
hour setting. Press the "+" or "-" buttons to set
125 V, 60 Hz, 15 A resistive
time. Be sure to cycle through until AM or PM
1000 W tungsten
appears correctly.
500 W electronic ballast
3. Press the "MANU" button to enter the "OFF" time
120 V, 60 Hz, 8.3 A standard ballast
minutes setting. Press the "+" or "-" buttons to set
1/3 HP
time.
4. You may now either press the PROG button to
enter additional programs (up to 8 programs), or
WARNING
press the TIME button (or wait 15 seconds) to
store your program. Your timer will now show the SUITABLE FOR USE WITH OUTDOOR
current set time and is ready for use. APPLIANCES – RAINTIGHT WHEN MOUNTED
VERTICALLY WITH THE RECEPTACLE FACING
DOWNWARD. NOT FOR WATER IMMERSION.
8. Manual Override
Federal Communications Commission Interference
Press the MANU button to choose the timer status.
Statement
Display Explanation This equipment has been tested and found to comply
with the limits for Class B digital device, pursuant to
ON Always ON
part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
OFF Always OFF
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency
Timer will turn ON/OFF according to the
AUTO
energy and, if not installed and used in accordance
program settings.
with the instructions, may cause harmful interference to
Run all events (programs) in a Random
radio or television reception, which can be determined
mode. This is a security feature in which
by turning the equipment off and on, the user is
RDM
ON and OFF times randomly differ ± 30
encouraged to try to correct the interference by one or
minutes from the programmed times,
creating a more "lived-in" look. The word
"RDM" appears in the display.
Page 2
more of the following measures: TROUBLESHOOTING
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
PROBLEM POSSIBLE CORRECTIVE
the receiver.
CAUSE ACTION
• Connect the equipment into an outlet on a circuit
Lights do Timer is not in a Move the timer to
different from that to which the receiver is connected.
not turn on good area for another location
• Consult the dealer or an experienced radio/TV
at dusk. light meter to where there is no
technician for help. function as there ambient light.
is too much
ambient light to
This device complies with Part 15 of the FCC Rules.
detect darkness.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and Lights do Lights are not in Be sure that lights
not turn on, "ON" position, are functional by
(2) this device must accept any interference received,
even when lights are not plugging them
including interference that may cause undesired
timer is in functioning, or directly into the
operation of the device.
"ON" timer is not outlet. Be sure that
position. receiving power. lights are in "ON"
FCC Caution: Any changes or modifications not position if they have
their own switch. Be
expressly approved by the party responsible for
sure that timer is
compliance could void the user's authority to operate
receiving power -
this equipment.
the LED should light
up when plugged
into an outlet and
put in the "ON"
CARE AND MAINTENANCE
position.
• Store indoors in dry location. Lights are The timer is in Move the lights
flashing Dusk to Dawn away from the timer,
• Always unplug when not in use.
(turning on mode, and the or reposition the
• Do not unplug by pulling on cord.
and off). light from the timer so that it does
plugged-in lights not face the lights.
is affecting the
light sensor.
WARRANTY
• For information on product warranty please call
customer service at 1-866-994-4148, 8 a.m. - 6 p.m.,
EST, Monday - Thursday, 8 a.m. - 5 p.m., EST,
Friday.
• This product is guaranteed to be free of defects for
a limited period of one year form the date of
purchase.
• If the product suddenly malfunctions and is not
damaged by external factors or personal reasons
within the one year warranty limit from the day of
purchase, the product maybe considered for repair.
If the product is damaged due to natural disaster like
fire, lightning, flood, hurricane, etc., the product will
not be considered for repair.
Page 3
Printed in China