Utilitech TM-097 S Installation Instructions

ITEM #0192773 Before initial use, if LCD screen is blank, connect with
power for at least 30 minutes to charge the internal
MODEL #TM-097 S
battery. After the screen displays, the unit is ready for
DAYLIGHT SAVING
programming.
IN-WALL TIMER
1. This device is to be installed in a wall box measuring
at least 3 in. x 2 in. x 2-1/2 in. (standard single gang
electrical wall box) and wired in
Strip Length:
Call customer service at 1-866-994-4148, accordance with National Electrical
8 a.m. - 6 p.m., EST, Monday - Thursday,
Code.
8 a.m. - 5 p.m., EST, Friday.
2. Straighten each conductor and strip 3/4 in.
of insulation from each wires.
PACKAGE CONTENTS
A B
3. Installing In-Wall Timer:
Begin by loosening all screws.
3
Ground
Neutral
Ground wire (Green)
Neutral
Neutral wire (White)
Hot wire
Load wire (Black)
Load
Hot wire (Black)
wire
C D
1. Insert the ground or bare wire(s) into the hole(s)
labeled "G" (near green screw) (see figure 3).
2. The timer requires a
PART DESCRIPTION QUANTITY
3-2-1
neutral wire connection
A Timer 1
or the timer will not work.
(1) If the neutral (white)
B Wall plate 1
wire has an appropriate
C Mounting screws (Wall box) 0.748 in. - 2
length, strip and twist
D Mounting screws (Wall plate) 0.33 in. - 2 together the ends of the
neutral (white) wires and
* Tools Required for Assembly (not included):
insert into the holes
flathead screwdriver.
labeled N (near silver
3-2-2
screw). (see figure
INSTALLATION INSTRUCTIONS 3-2-1).
(2) If the neutral wire from
Warning: To avoid fire and/or shock, turn off power. the wall box is short
and does not reach the
Make sure the power is off before wiring. If you are
unsure or uncomfortable with installation, contact a timer, use the enclosed
The spare
licensed electrician. jumper kit to extend the
(white) wire.
wire connection. Begin
by connecting one end
AB16776
of the supplied wire (white) to the neutral wires 6. Press the " " or " " button until the display shows
from the wall and secure it with a wire nut. the current DAY then press SET/RE button.
Then, insert the two neutral (white) wires into 7. Press the " " or " " button until the display shows
the holes labeled N (near silver screw)(see the current HOUR then press SET/RE button.
figure 3-2-2). 8. Press the " " or " " button until the display shows
3. Insert the hot wire into the hole labeled "L-I" (near the current MINUTE then press SET/RE button.
brass screw) (see figure 3). 9. Press the " " or " " button to turn on or turn off
4. Insert the load wire into the hole labeled "L-O" Day-Light-Saving-Time(DST) function
(near brass screw). The screw terminal accepts SET/RE button.
14AWG-12AWG copper wire (12AWG maximum).
3/4"
(1.9cm) (see figure 3). NOTE: When setting the current time during the
5. Tighten all screws firmly Day-Light-Savings Time period, and your DST
(see figure 3-5). function is ON, your current time should be the
6. Carefully fold wire into time after DST.
wall box and mount timer
(A) into wall box using 10. Press the " " or " " button to choose the AREA
mounting screws (CC), you live then press SET/RE button to complete
Wall
then attach the wall plate time setting.
using the mounting
NORTH: NOR / CENTER: CEN / SOUTH: SOU
screws (DD).(see figure 3-6).
NORTH
3-6
CENTER
SOUTH
2. Set an ON/OFF Program for Sunrise/Sunset
This unit's sunrise/sunset schedule is based on USA
7. Restore power by flipping the breaker to the "on"
astronomic zones. The actual sunrise/sunset
position or re-installing the fuse to the circuit.
schedule may slightly differ from east to west. You
can set the actual sunrise/sunset time today. This
OPERATING INSTRUCTIONS unit will memorize the difference and auto-adjust for
following dates.
1. Setting the Clock
1. Press button to show
current sunrise time
1. Open the door.
(see Diagram 2-1).
2. Press TIME button.
• Press " " to increase
3. Display will flash for a 15 seconds. If no other number. Press " " to
action taken, clock may engage with the incorrect
decrease number.
time.
Setting range: MAX
4. Press the " " or " " button until the display shows +/- 1 hour. Once you
the current YEAR then press SET/RE button.
complete the time
5. Press the " " or " " button until the display shows setting press SET/RE button.
the current MONTH then press SET/RE button.
2. press " " or " " to turn on or turn off the device NOTE: If the timer is not in "Manual (ON or OFF)"
during the sunrise time. Then press SET/RE mode, it will obey the next programmed event. This
button. allows the user to manually turn a light on and allow
the program to shut the light back off at a preset time.
3. The display will show
3-1
current sunset time
5. Setting Programs
(see Diagram 3-1).
then press • Press " " to increase
Timer has up to 7 customizable ON/OFF Event
number. Press " " to
PM
Settings to turn devices on and off at different times
decrease number. ON
and on different days as programmed.
Setting range: MAX
+/- 1 hour. Once you
ON/OFF
1. Press MODE repeatedly until the display
complete the time
shows AUTO.
setting press SET/RE button.
2. Press the PROGRAM
4. press " " or " " to turn on or turn off the device
button once. The display
during the sunset time. Then press SET/RE
will look as shown at the
MODE
button to complete the setting.
right. The " ON " in
lower right hand corner
TIME
3. Operating the Time Switch reset
indicates that you are now
programming EVENT 1
PROGRAM SET/RE
NORTH Press the MODE button repeatedly to set the timer
which you want your
to Automatic, Random or Manual mode.
device turned ON.
CENTER
3. Press the SET/RE button to set up the time.
NOTE: For the time switch to run programmed
4. Press the " " or " "
events, it must be set to "AUTO" mode.
display shows the DAY(s) when you want then
SOUTH
press SET/RE button.
• AUTO — runs all events automatically, according
The options are:
to the schedule you have set. The word "AUTO"
• All days of the week (MO TU WE TH FR SA SU)
appears in the display.
• Individual days of the week (MO, etc.)
• RDM (Random) - Timer will randomly turn devices
• Weekdays only (MO TU WE TH FR)
ON/OFF within15 minutes 5 times per day. This is
• Weekends only (SA SU)
a security feature in which ON and OFF times
5. Press the " " or " "
randomly, creating a more "lived-in" look.
display shows the HOUR when you want then
• MANUAL (ON or OFF) — turns always ON or OFF
press SET/RE button.
only when user presses the ON or OFF button.
6. Press the " " or " "
The display is blank, showing neither RDM nor
display shows the MINUTE when you want then
AUTO.
press SET/RE button.
• (Astronomic) — Timer will turn devices ON or
7. Repeat Steps 3, 4, 5, 6 to set the OFF time for
2-1
OFF only during sunrise/sunset time you have set.
Event 1.
4. Overriding Timer Settings
SU
4
Two kinds of settings can cause the timer to work in
AM
an unexpected way:
The ON/OFF buttons AM
ON
- Set up events in progressive order of time (for
override the current ON
AUTO example, 8:00 pm ON, 9:00 pm ON, 10:00 pm ON
programmed events. To
ON/OFF
— NOT 8:00 pm ON, 10:00 pm ON, 9:00 pm ON).
override the current
ON/OFF
- Do not overlap event times (for example, 8:00 pm
program, press the ON/OFF
ON /12:00 pm OFF, and 9:00 pm ON / 11:00 pm
button.
OFF).
MODE
MODE
TIME
reset
TIME
reset
PROGRAM SET/RE
6. Reviewing Events Programmed interference in a residential installation. This equipment
generates, uses and can radiate radio frequency
1. In the current time display, press the PROGRAM energy and, if not installed and used in accordance
button repeatedly to check your settings. with the instructions, may cause harmful interference to
2. When finished, press the TIME button to return radio or television reception, which can be determined
the display to the time of day. by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or
more of the following measures:
7. Clearing (Deleting) an Event
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
1. Press the PROGRAM button as many times as
the receiver.
necessary to locate the setting you want to clear.
• Connect the equipment into an outlet on a circuit
2. Press and hold the SET/RE for 3 seconds button.
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
3. When finished, press the TIME button to return
5-2
technician for help.
the display to the time of day.
This device complies with Part 15 of the FCC Rules.
the
HELPFUL TIPS Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and
• In case of an operational failure of the timer, use a
ON (2) this device must accept any interference received,
paper clip and insert into the RESET hole to clear all
including interference that may cause undesired
the settings and restart.
operation of the device.
FCC Caution: Any changes or modifications not
SAFETY INFORMATION
button repeatedly until the
expressly approved by the party responsible for
Please read and understand this entire manual before compliance could void the user's authority to operate
attempting to assemble, operate or install the product. this equipment.
THIS TIMER IS FOR USE WITH A 125 V AC POWER
CAUTION
SOURCE. 125 V AC / 60 Hz
• Do not attach a device that exceeds the unit ratings
as described in the Safety Information section of this
DO NOT ATTACH A DEVICE THAT EXCEEDS THE
button repeatedly until the
manual.
UNIT RATINGS:
• Wattage of lamps or appliances controlled must NOT
15 A / 1,875 Resistive (General Purpose)
exceed rated capacity.
8 A / 1,000 W Tungsten (Incandescent)
button repeatedly until the
• FOR INDOOR USE ONLY.
8.3 A / 996 W Standard Ballast (Fluorescent)
• Installation by a licensed electrician to local, state
500 VA Ballast (Electronic)
and national codes is recommended.
1/2 HP (Horsepower Motor)
• Remove wall plate and make sure both hot and
neutral wires are present in the junction box. If both
WARNING
wires are not present, additional wiring will be
TO AVOID FIRE, SHOCK, OR DEATH, TURN OFF
necessary before installation can be completed.
POWER AT CIRCUIT BREAKER AND TEST THAT
• Check that all wire connections are secure.
POWER IS OFF BEFORE WIRING.
• Place all wires inside junction box. Fit timer into
junction box.
This equipment has been tested and found to comply • Reconnect electrical power.
with the limits for Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
WARRANTY
• For information on product warranty please call
customer service at 1-866-994-4148, 8 a.m. - 6 p.m.,
EST, Monday - Thursday, 8 a.m. - 5 p.m., EST,
Friday.
• This product is guaranteed to be free of defects for
a limited period of one year from the date of
purchase.
• If the product suddenly malfunctions and is not
damaged by external factors or personal reasons
within the one year warranty limit from the day of
purchase, the product maybe considered for repair.
If the product is damaged due to natural disaster like
fire, lightning, flood, hurricane, etc., the product will
not be considered for repair.
TROUBLESHOOTING
PROBLEM POSSIBLE CORRECTIVE
CAUSE ACTION
Timer turns 1. Programmed 1. Press PROGRAM
ON/OFF at event(s) are button to review the
incorrect incorrect. settings and revise
times or 2. Timer is in them as necessary.
skips some RANDOM mode, See OPERATING
of the which varies INSTRUCTIONS.
programmed switching times 2. If you don't want to
times. up to 15 minutes keep the timer in
(to give your home RANDOM mode,
a "lived-in" look). press MODE to
change to AUTO
mode.
The attached The timer is wired Disconnect wires,
device turns incorrectly. remove timer,
off re-install per the
immediately instruction manual. If
after being problem persists,
turned on. contact certified
electrician.
LCD screen The included Battery will
is blank. rechargeable automatically
battery has lost its recharge after
charge. installation.
LCD screen The light or Make sure the light
is on but attached device or attached device is
attached itself may be switched ON.
device is off. switched OFF.
Printed in China