Remote Control Unit; Part Names; Turning The Tv On/Off - Sharp AQUOS LC-32M300M Operation Manual

Remote control unit

9
1
10
11
2
12
3
13
14
4
15
5
16
6
17
18
7 19
8
20
1 e (Mute)
Press e s Mutes sound.
Press e again s Restores sound.
Mute will be cancelled after 30 minutes. However,
the TV will not suddenly output loud sound as the
volume level will be set to 0 automatically. Increase
the volume level by pressing VOL k.
2 0 – 9
Set the channel.
TELETEXT mode: Set the page. (See page 14.)
3 A (Flashback)
Press A to return to the previous selected channel
or external input mode.
4 WIDE
Change the wide image mode. (See pages 13 and 14.)
5 VOL k /VOL l
Set the volume.
(VOLk) Increase the volume.
(VOLl) Decrease the volume.
6 FREEZE
Freeze a motion picture on the screen. (See page
13.)
Inserting the battery
Before using the TV for the fi rst time, insert a "AA" size battery (supplied). When the battery become depleted
and the remote control fails to operate, replace the battery with new "AA" size battery.
1 2
Open the battery cover. Insert the supplied "AA" size battery.
• Place battery with their terminals corresponding to the
(e) and (f) indications in the battery compartment.
CAUTION
• Battery (battery pack or battery installed) shall not be exposed to excessive heat such as sunshine, fi re or the like.
7 EXIT
Return to the default screen.
8 Colour (Red/Green/Yellow/Blue)
TELETEXT mode: Select a page. (See page 14.)
9 POWER (STANDBY/ON)
To switch the power on and off. (See page 6.)
10 DISPLAY
Display the channel or input information.
11 SLEEP
Set the Sleep timer.
0 hr. 30 min. 1 hr. 00 min. 1 hr. 30 min.
Off 2 hr. 30 min. 2 hr. 00 min.
12 AV MODE
Select an audio and video setting. (See page 8.)
13 MPX
Select the sound multiplex mode.
14 TV/VIDEO (INPUT SOURCE)
Select an input source.
15 CH a /CHb
TV input mode: Select the channel.
(CH a ) Increase the channel number.
(CHb) Decrease the channel number.
TELETEXT mode: Select the page. (See page 14.)
16 PC
Directly select the PC terminal.
17 MENU
Display the menu screen.
18 a /b/ c / d (Cursor)
Select a desired item on the setting screen.
ENTER
Execute a command.
19 RETURN
MENU mode: Return to the previous menu screen.
20 m (TELETEXT)
Select the TELETEXT mode. (all TV image, all TEXT image,
TV/TEXT image) (See page 14.)
k (Reveal hidden for TELETEXT)
TELETEXT mode: Display hidden characters. (See page 14.)
[ (SUBTITLE for TELETEXT)
To turn the subtitles on. (See page 14.)
3 (Hold)
TELETEXT mode: Stop updating Teletext pages automatically.
Press 3 again to release the hold mode. (See page 14.)
1 (Subpage)
Display the Teletext subpage directly when in Teletext mode.
(See page 14.)
v (Top/Bottom/Full)
TELETEXT mode: Set the area of magnifi cation. (See page 14.)
3
Close the battery cover.

Part names

TV (Front)
Remote control sensor
OPC sensor
POWER indicator
Light off
Lighted (Red)
Lighted (Green)
TV (Rear)
ANALOGUE RGB (PC)
6
7
8
* The INPUT 1 and INPUT 5 terminals can both use the same audio input terminal. However, the proper item must be
selected in the "PC Audio Select" menu. (See page 12.)
** Usually do not connect anything to this terminal as it is reserved only for service personnel.
• The illustrations in this operation manual are for explanation purposes and may vary slightly from the actual operations.

Turning the TV on/off

Turning on/off the power
• To turn on the power
Press POWER on the TV. (After a few seconds, an image
appears with sound.)
• To turn off the power
Switch it off by pressing POWER on the TV.
NOTE
• If you are not going to use this TV for a long period of time, be sure to remove the AC cord from the AC outlet.
• Minor power is consumed when the unit is in standby mode.
5 6
Power off
The TV is in standby mode.
The TV is on.
1 POWER (On/Off) button
2 MENU button
3 TV/VIDEO button
4 Channel up (r)/down (s) buttons
5 Volume up (e)/down (f) buttons
6 Antenna input terminal
7 INPUT 5 (PC) terminals*
8 INPUT 1 (HDMI) terminal*
9
9 RS-232C terminal
10 SERVICE ONLY terminal**
10
1
11 INPUT 2 terminals
2 12 INPUT 3 terminals
13 INPUT 4 terminals
3
11
4
12
13
5
Standby mode
• To standby mode
If the TV is switched on, you can switch it to standby by
pressing POWER on the remote control.
• Switching on from standby
From standby, press POWER on the remote control.