Page 1
Models 7136-000-500 & 7176-000-090-500 Adult Assembly Required KETTLER ® International Inc. • 1355 London Bridge Road • Virginia Beach, VA 23453 USA Please do not return this product to the store. Contact KETTLER® for parts and service: call toll free 866.804.0440 or send email to...
The knowledge gained in this process is used to constantly improve and develop our products. In order to offer our customers the very best in product quality, we reserve the right to make technical changes at any time. In spite of this, should you have any cause for complaint, please contact KETTLER Note on Safety •...
• Separate all the parts including the hardware. Compare quantities with the package contents section and that all items are undamaged. If there are any problems, please contact KETTLER • Before assembling the equipment, study the drawings and photos carefully then assemble in the order shown.
Page 4
Package Contents (continued) Number Incl. - 1-6mm, 2-8mm Number Incl. - 2 (outdoor only) Number Included - 1 Number Included - 1 Items below are shown at actual size Number Included - 2 m6x37 Number Included - 2 m6x30 Number Included - 2 Number Included - 2 Number Included - 4 m8x45...
Page 5
Package Contents (continued) Items below are shown at actual size Number Included - 2 Number Included - 18 Number Included - 8 Number Included - 8 Number Included - 4 m12x6x15 Number Included - 4 Number Included - 4 Number Included - 4 Number Included - 2 m26x19x6 m16x8x3...
Page 6
Assembly Begin the assembly of your table by carefully removing the plastic wrap and all of the loose contents. Separate the two table tops by removing the four plastic corner protectors and the plastic side strips. Step 1 2 Required Align footlock with stemtube.
Page 7
Assembly Step 2 End view and perspective view 8 Required Paying attention to position of wheelbase, assemble the stemtubes to base in order shown. Insert endcaps. Assemble two wheelbase assemblies. 4 Required 4 Required m8x125 4 Required 4 Required dia 25x8 8 Required 4 Required dia 16x8...
Page 8
Assembly Step 2 (continued) Photo K shows the non locking stemtube being installed. Step E to step J are the same for the locking and non locking stemtube.
Page 9
Assembly Step 3 2 Required Install non-locking wheels. Do not over torque; wheels should roll smoothly. Install non-locking wheels on both wheelbase assemblies. 8 Required dia 16x8 m8x110 2 Required...
Page 10
Assembly Step 4 2 Required Install locking wheels. The grooves of wheels should face inward. Again, do not over torque; wheels should roll smoothly. Push down foot lock to lock the wheels.Install non-locking wheels on both wheelbase assemblies. 8 Required dia 16x8 m8x110 2 Required...
Page 11
Assembly Step 5 Paying attention to position of wheelbase, snap alignment struts into place. Bolt locking struts to base. Bolt the locking strut with thumb latch to the same side as locking wheels. Bolt strut without latch to the side of non-locking wheels. Assemble two identical wheelbase assemblies with wheels and struts.
Page 12
Assembly Step 6 M8 threads M6 threads 2 Required m8x45 Bolt one M8 crossbar between each wheelbase. This crossbar is being assembled temporarily to create a support base and will be removed at a later step. For outdoor tables only: slide the shimpad onto wheelbase (steps B, C, and D).
Page 13
Assembly Step 7 4 Required 2 Required m6x50 Insert endcap into the bottom of netpost bar. Using M6 crossbar, assemble crossbar and netpost bars to alignment struts. The netpost bar installation is repeated on the other wheelbase assembly. Fastener quantities include installation on both wheelbase assemblies.
Page 14
Assembly Step 8 4 Required Screw eyelets to four Jbars. Assemble safety levers to two of the Jbars. Slide handgrip onto safety lever. Note the orientation of the slot in the safety lever and the Jbar as shown in photo E. 4 Required 2 Required dia 12x6...
Page 15
Assembly Step 9 Screw eyelets to support leg on table-top half. Repeat for second table-top half. 4 Required 3.9x13 4 Required Support Leg...
Page 16
Assembly Step 10 Jbar Support Leg 2 Required m8x45 Support Leg Jbar Wheelbase Support Leg Jbar Important: have two people complete steps 10-12. With assistance, lift one table top onto the wheelbase; the legs will be facing outward. Have one person support the top while it is resting on the base while the other completes assembly.
Page 17
Assembly Step 11 1 Required m6x37 Raise safety lever up straight. Bolt the safety lever to leg. Bolt the Jbars to leg. Insert footcaps. 2 Required m6x60 End view and side view shown - 2 Required m12x6x15 2 Required 3 Required dia 12x6 m 12x6x3 4 Required...
Page 18
Assembly Step 11 continued Step 12 Bolt locking struts to support leg. 2 Required m6x49 4 Required 2 Required m12x6 Now, remove the temporary crossbar assembled in step 6. Carry out steps 10-12 again for the other side.
Page 19
Assembly Open Table Top to Complete Assembly To properly open table into playing position: lock wheels (H), push the thumb latch down on the left locking strut. Squeeze the strut on the right side and lower table into playing position. Support the table as you lower it;...
Page 20
Assembly Step 13 Step 14 Attach ball/racquet holder to netpost. Slide net post onto netpost bar and screw into place. Insert guide plug. Repeat on other side of table. 2 Required 4.8x25 2 Required...
Page 21
Assembly Step 15 Screw sideshroud into place. Repeat installation of second shroud on opposite side wheelbase assembly. 6 Required 3.9x25 3 Screws...
Assembly Net Assembly Net assembly: Slide Jpin through net.. Place Jpin in designated slots. Tie string to tension tab. Place string in slots over Jpin and net post. Adjust net tension by adjusting tension tab. Remove protective plastic film from table surface.
Assembly Remove Film Folding Table Remove protective plastic film from table surface. Folding Table: To properly fold the table, lock the wheels, press the safety lever up and lift top. Once the top is halfway up you can release lever and continue to fold the top.
United States only. Any shipment outside of the United States will be at the sole cost of the customer. This KETTLER ® Limited Warranty is a manufacturer’s warranty and is not changed or modified by additional warranties extended by individual retailers at the point of sale.
Important: Spare part prices do not include fastening materials; if fastening material (bolts, nuts, washers, etc.) is required, this should be clearly stated on the order by adding the words “with fastening material.” Contact: KETTLER International Inc., 1355 London Bridge Road, Virginia Beach, VA 23453 USA ®...
Page 27
Spare Parts Number Description Footcap Clamp (outdoor table) Clamp 25mm (indoor table) Clamp 18mm (indoor table) Support Leg Wheelbase Stemtube for non-locking wheel (3437) Locking Strut with thumb latch Locking Strut without thumb latch Safety Lever Crossbar M8 Endcap 40x25mm Handgrip Hardware Bag (not illustrated) Shimpad (pair) (outdoor table)
Page 28
® without the prior written permission of KETTLER KETTLER ® International Inc., 1355 London Bridge Road, Virginia Beach, VA 23453 USA www.kettlerusa.com •...