Ic Pin Function Description - Sony XR-C5200 Service Manual

6-7. IC PIN FUNCTION DESCRIPTION

• MAIN BOARD IC501 MN101C12GTB1 (SYSTEM CONTROLLER)
Pin No. Pin Name
1 AVREF–
2
VSM
3 KEYIN1
4 KEYIN0
5 D-BASS IN
6 DSTSEL
7 FUNC-SEL
8
NCO
9 RC-IN0
10 AVREF+
11 VDD
12 OSC OUT
13 OSC IN
14 GND
15 XT IN
16 XT OUT
17 GND
18 RC-IN1
19 SYSRST
20 BUS-ON
21 UNISO
22 UNISI
23 UNICKO
24 UNICKI
25
NCO
26 KEYACK
27 NOSESW
28 BU-IN
29 SIRCS
30
TEL-ATT
31 TEST-IN
32 RAMBU
33 RESET
34 VOL-MUT
35
BEEP
36 AMP-MUT
I/O
I
Reference voltage (0V) input terminal (for A/D converter)
FM and AM signal meter voltage detection input from the FM/AM tuner unit (TU1)
I
(A/D input)
Key input terminal (A/D input) (LSW921 to LSW923, LSW927 to LSW933)
I
6, PRESET DISC –/+, DSPL, 6, 5, 4 n, 3 PLAY MODE, 2 SET UP, 1 N keys input
Key input terminal (A/D input) (LSW901 to LSW903, S901, LSW905, LSW906)
OFF, SOURCE, MODE *, SEEK/AMS = 0 – + ) +, SOUND, SHIFT keys
I
input
I D-BASS switch (S981) input terminal (A/D input)
Destination setting terminal Frequency select switch (S502) input terminal
I
("L": MW 9 kHz/FM 50 kHz step, "H": MW 10 kHz/FM 200 kHz step)
I
Setting terminal for the function select (fixed at "H" in this set)
O
Not used (open)
I Rotary remote commander key input terminal (A/D input)
I
Reference voltage (+5V) input terminal (for A/D converter)
—
Power supply terminal (+5V)
O Main system clock output terminal (18.432 MHz)
I Main system clock input terminal (18.432 MHz)
—
Ground terminal
I
Sub system clock input terminal (32.768 kHz)
O
Sub system clock output terminal (32.768 kHz)
— Ground terminal
I Rotary remote commander shift key input terminal "L": shift
O
Reset signal output to the SONY bus interface (IC581) "L": reset
O Bus on/off control signal output to the SONY bus interface (IC581) "L": bus on
O Serial data output to the SONY bus interface (IC581)
I Serial data input from the SONY bus interface (IC581)
O Serial data transfer clock signal output to the SONY bus interface (IC581)
I Serial data reading clock signal input for the SONY bus interface Not used (open)
O
Not used (open)
Input of acknowledge signal for the key entry Acknowledge signal is input to accept function
I
and eject keys in the power off status On at input of "H"
Front panel block remove/attach detection signal input terminal
I
"L": front panel is attached
Battery detect signal input from the SONY bus interface (IC581) and battery detect circuit
I
"L" is input at low voltage
I Sircs remote control signal input terminal Not used (fixed at "L")
I Telephone muting signal input terminal At input of "H", the signal is attenuated by –20 dB
I Setting terminal for the test mode "L": test mode, Normally: fixed at "H"
Internal RAM reset detection signal input terminal
I
Input terminal to check that RAM data are not destroyed due to low voltage
This checking is made within 100 msec after reset Fixed at "L" in this set
System reset signal input from the reset signal generator (IC551) and reset switch (S551)
I
"L": reset "L" is input for several 100 msec after power on, then it changes to "H"
Muting control signal output to the electrical volume (IC331)
O
Volume minimum: "∞" output ("H" active)
O Beep sound drive signal output terminal
O Muting on/off control signal output to the power amplifier (IC751) "L": muting on
Function
– 31 –