Table of Contents
Advertisement
KV-BT212M40/M50/M70/M80/M90/N80
5.Write into memory by pressing [MUTING] then
the remote commander.
WIDE MODE (50Hz)
(V-Compression Adjustment)
1. Input SPCB signal.
2. Adjust condition change to WIDE MODE : ON
3. Copy (Item from normal mode 50Hz) all Normal
Mode adjusted data.
NORMAL MODE (60Hz)
1. Input 525/60Hz signal.
2. They can copy 50Hz first.
("COPY" under GEOM is set to
3. Using the
and
1
(Service Mode).
4. Raise/lower data using the
obtain optimum image.
GEOM :
000
HPOS
001
HPAR
002
HBOW
003
VLIN
004
VSCR
005
HSIZ
006
EWPW
007
UCOP
008
LCOP
009
EWTZ
010
VSLP
011
VSIZ
012
SCOR
013
VPOS
014
VZOM
015
HBL
016
WBF
017
WBR
018
SBL
019
COPY
WIDE MODE (60Hz)
(V-Compression Adjustment)
1. Input mono scope signal/NTSC monoscope signal
(for NTSC model)
2. Adjust condition change to WIDE MODE : ON
3. "COPY" is set to
3-5.
PICTURE DISTORTION ADJUSTMENT
H. CENTER ADJUSTMENT (HPOS)
1. Input Monoscope signal/NTSC monoscope signal
(for NTSC model).
2. Activate the Service Adjustment Mode.
3. Select the HPOS item with
4. Adjust the value of HPOS with
vertical center.
5. Press [MUTING] then
RM-W101 RM-W150
-
, then [MUTE] +
1
button, select category GEOM
4
and
buttons to
3
6
Horizontal Shift (HS)
Horizontal Parallelogram
Horizontal Bow
Vertical Linearity
Vertical Scroll
EW Width (EW)
EW Parabola/Width (PW)
EW Upper Corner Parabola
EW Lower Corner Parabola
EW Trapezium
Vertical Slope (VS)
Vertical Amplitude
S-Correction (SC)
Vertical Shift (VSH)
Vertical Zoom (VZ)
RGB Blanking Mode
Timing of Wide Blanking (WBF)
Timing of Wide Blanking (WBR)
Service Blanking
Copy the GEOM data to all
50/60Hz NVM area
, then [MUTE] +
1
-
and
.
1
4
and
for the best
3
6
to save into the memory.
-
on
H. SIZE ADJUSTMENT (HSIZ)
1. Input Monoscope signal/NTSC monoscope signal
(for NTSC model).
2. Activate the Service Adjustment Mode.
3. Select HSIZ with
4. Adjust with
5. Press [MUTING] then
V. SIZE ADJUSTMENT (VSIZ)
1. Input Monoscope signal/NTSC monoscope signal
)
-
(for NTSC model).
2. Activate the Service Adjustment Mode.
3. Select the VSIZ item with
4. Adjust value of VPOS with
vertical center.
5. Press [MUTING] then
V. CENTER ADJUSTMENT (VPOS)
1. Input Monoscope signal/NTSC monoscope signal
(for NTSC model).
2. Activate the Service Adjustment Mode.
3. Select the VPOS item with
4. Adjust value of VPOS with
vertical center.
5. Press [MUTING] then
– 32 –
and
.
1
4
and
for the best horizontal size.
3
6
to save into the memory.
-
and
.
1
4
and
for the best
3
6
to save into the memory.
-
and
.
1
4
and
for the best
3
6
to save into the memory.
-
Hide quick links:
Advertisement
Table of Contents
