Kenwood KDC-X879 Instruction Manual page 29

1st section
Multi-function key operation
[2] [2] "FRONT"
"X'Over" [3] "REAR"
[4] "CNTR"
[5] "SW"
[5] "PHASE"
[3] [2] "FRONT"
"DTA" [3] "REAR"
[4] "CNTR"
[5] "SW"
[4] [2] "FRONT" [2] "BASS"*
"EQ" [3] "MID"*
[4] "TRE"*
[3] "REAR" [2] "BASS"*
[3] "MID"*
[4] "TRE"*
[4] "CNTR" [2] "BASS"*
[3] "MID"*
[4] "TRE"*
[5] [2] "FRONT" [2] "Front-L"
"SP- [2] "Front-R"
LEV" [3] "REAR" [3] "Rear-L"
[3] "Rear-R"
[4] "CT/SW" [4] "Center"
[4] "Sub Woofer"
2
* [5] "T-TONE"
• * The followings can be adjusted each time button [2]
"BASS", button [3] "MID" or button [4] "TRE" of "EQ"
functions is pressed.
[2]"BASS" : "BASS F" (Bass Center Frequency)
"BASS L" (Bass Level)
"BASS Q" (Bass Q Factor)
[3]"MID" : "MID F" (Middle Center Frequency)
"MID L" (Middle Level)
"MID Q" (Middle Q Factor)
[4]"TRE" : "TRE F" (Treble Center Frequency)
"TRE L" (Treble Level)
"TRE Q" (Treble Q Factor)
2
• * You can listen to the "T-TONE" when you have
tuned it. The sound level is reduced when "T-TONE"
is selected. The sound returns to the normal level
when the original source is selected.
• X'over (Crossover Network Setup)
You can manually set a crossover frequency of
speakers.
• DTA (Digital Time Alignment)
Manually set the sound output timing of each
channel.
• EQ (Equalizer)
You can manually set the equalizer curve.
• SP-LEV (Speaker Level)
Set the volume at each setup position.
2nd section
Audio setup Item
High Pass Filter Front
High Pass Filter Rear
High Pass Filter Center
Low Pass Filter Subwoofer
Subwoofer Phase setting
DTA Front
DTA Rear
DTA Center
DTA Subwoofer
EQ Front Bass setting
EQ Front Middle setting
EQ Front Treble setting
3
EQ Rear Bass setting
EQ Rear Middle setting
EQ Rear Treble setting
EQ Center Bass setting
EQ Center Middle setting
EQ Center Treble setting
SP-LEV Front Left
SP-LEV Front Right
SP-LEV Rear Left
SP-LEV Rear Right
SP-LEV Center
SP-LEV Subwoofer
SP-LEV Test tone
4
Multi-function key operation
[2] [2] "USER"
"MEMORY" [3] "INST"
[3] [2] "USER"
"CALL" [3] "INST"
• You can store an adjusted audio setup value by
" "
selecting MEMORY . Also, you can recall it by
" ".
selecting CALL Refer to 'Audio Setup memory Recall'
(page 30).
Adjust the Audio setup item
Press the [4] or [¢] button.
Each time the button is pressed the setting
switches as shown below.
Adjustment Item
High Pass Filter Front
High Pass Filter Rear
High Pass Filter Center
Low Pass Filter Subwoofer
Subwoofer Phase setting
DTA Front/DTA Rear/
DTA Subwoofer
DTA Center
Bass Center Frequency
Middle Center Frequency
Treble Center Frequency
Bass Level/ Middle Level/
Treble Level
Bass Q Factor/ Middle Q Factor/
Treble Q Factor
SP-LEV Front Left/SP-LEV Front Right
SP-LEV Rear Left/SP-LEV Rear Right
SP-LEV Center/SP-LEV Subwoofer
• The Adjustment item can also be controlled by the
rotary volume knob. Refer to 'Rotary Volume knob
operation mode select' (page 14).
• To get the best sound, first set the "CABIN" and "SP-
SEL" parameters using the 'Audio Setup (Easy mode)'
(page 28). Refer to 'Notes on Sound Management
System' (page 12).
• When the 'Dual Zone System' (page 25) is ON, each of
the following setup is ignored.
- "X'over"/ "EQ" / "DTA"
Exit Audio setup mode
Press the [6] ("RTN") button.
Audio setup item
User Memory
User Insttaller
Call User
Call Insttaller
Range
Through/30 — 250 (Hz)
30 — 250 (Hz)
Normal/ Reverse
0 — 20.33 (feet)
0 — 5.67 (feet)
60 — 400 (Hz)
500 (Hz) — 3.15 (KHz)
4.00 (kHz) — 16.00 (KHz)
-9 — +9 dB
0.25/ 0.50/ 1.00/ 2.00
-10 — +10
29
|
English