Table of Contents
Advertisement
_iiii_i_ii_i
SECTION
2 _J_J_J:,_:,_]
HOW YOUR WATER SOFTENER
WORKS
A. FACEPLATE
TIMER FEATURES
S
C
T
N
JJJJJJJJJJJJJJJJ.
J_JJJJJJJJJJJ_JJJ
JJJ_JJJ_JJ_JJ_
JJ
JJJJ_JJJJ_
JJ
JJJJJJJ_J
JJ
J_JJJJJJJJ
J_
_JJJJJJJJ_
JJ
_J_JJJJJJJ_
JJ
_J_JJ
JJ
_JJJJJ_JJ
JJJ_JJJJJJJJJJ_J_
JJJJ_JJ_JJ_JJ_JJ
•
EXTRA
RECHARGE
Sometimes,
a manually
started
regeneration
(recharge)
may
be
desired,
or needed.
Two
exam-
ples
are:
- You have used
more
water
than
usual
(guests
visiting)
and
you
may
run out of soft water
before
the next
timer
started
regenera-
tion.
- You did
not refill
the softener
with salt before
it was gone. After
you
refill with
salt:
You can start a regeneration
right
away,
or you
can set the timer
to
regenerate
at the next 2:00 AM (or
other
preset
recharge
time).
Do
the following.
•
RECHARGE
NOW
'_' _
_'_1
"
"
Press
the ON/OFF-HOLD
but-
;
ton and hold until
*RECHARGE,
',
Serv and
Fill begin
to flash
in the display.
Upon
reaching
fill, the first cycle of regeneration,
the flash-
ing Serv goes off and Fill is on steady.
RECHARGE
continues
to flash.
This regeneration
will last
for
about
2 hours.
After the 2 hours,
you will have soft
water
again.
*Note:
If the CLEAN
feature
is set to ON, a cleaning
back-
wash
(CLEAN and Bkwsh or Rinse flashes
in the dis-
play,
along with
the minutes
of the clean
cycle re-
maining)
precedes
the recharge.
•
RECHARGE
TONIGHT
i
/.uo
/
Press and release
(do not hold) the
_,_
_o.,o.
ON
/
OFF-HOLD
button.
RE-
CHARGE
TONIGHT
flashes
in the display,
and the
softener
begins
regeneration
at the next
preset
re-
charge
time. Press and release
the ON/OFF-HOLD
button
once more if you decide
to cancel
the regen-
eration,
and RECHARGE
TONIGHZ
•
SALT MONITOR
SYSTEM
The face plate
timer
has a low salt monitor
with an
indicator
light
to remind
you
to refill the storage
tank with
salt. To set this monitor
system:
_Lift
the salt hole cover
and level
the salt in the
storage
tank.
m
The salt level decal,
on the brineweU
inside
the
tank,
has numbers
from 0 to 8 (see drawing
be-
low). Observe
the number
the leveled
salt is at
or closest
to.
_I
Now,
press
the SALT LEVEL
ADJUST
button
until black
bars display
up to the salt level num-
ber. For example,
the pictures
below
show
the
salt level
at 6.
_
Finally,
set the level you want
the low salt indi-
cator light to come on. Press the SIGNAL
LIGHT
ADJUST
button
until a (÷) shows
opposite
this
number.
In the example
below,
the light
will
come on when
the stored
salt drops
to level 2. At
level 2, the storage
tank is about
1/3 full. This is
the lowest
you should
allow the stored
salt level
to drop
to (see note on page
1-6).
_
If you wish to turn the salt monitor
off, press the
SIGNAL
LIGHT
ADJUST
button
until
OFF
shows
above.
Note:
Your salt monitor
is an estimate
of your salt level; ac-
curacy
depends
on the type
of salt used
and other
regeneration
characteristics.
salt
level
LEVEL
u_V_
bars, salt
SALT
level
LEVEL
8
11116
brinewell
_4
decal
_
3
12_
_13($
RECI_ARGE
TONIGHT
RECHARGE
NOW
indicator light
LOW
SALT
2-1
Problems,
Questions?
Call
1-800-426-9345
Kenmore
Water
Line
Hide quick links:
Advertisement
Table of Contents
