_iii_ii_i
SECTION
2 _."_,'_.'_,',',"
HOW YOUR WATER SOFTENER
WORKS
A. FACEPLATE
TIMER FEATURES
S
E
C
T
N
eJ_JJJJJJJJJJ_JJJ.
iJJJJJJJJJ_J_JJJJJ,
IJJJ_JJJ_JJJJJ°
;JJ
_JJJJJJJJ.
iJJ
J_JJJJJJJ.
iJJ
J_JJJJJJJ.
iJ_J
_JJJJJJJJ.
iJJ
_JJJJJJJJJ_.
iJJ
JJJJJJJJJ.
mJJ
JJJJ_JJJJJ_
i_JJ_JJJ_JJJJJJ
I
iJJJJJ_JJJJJJJJJJJ
i_JJ_JJ_J_JJJJJ_
•
EXTRA
RECHARGE
Sometimes,
a manually
started
regeneration
(recharge)
may
be
desired,
or needed.
Two
exam-
ples are:
- You have used more water
than
usual
(guests
visiting)
and
you
may
run out of soft water
before
the next
timer
started
regenera-
tion.
- You did
not refill
the softener
with salt before
it was gone. After
you refill with
salt:
You can start a regeneration
right
away,
or you can set the timer
to
regenerate
at the next 2:00 AM (or
other
preset
recharge
time).
Do
the following.
Press andrelease
(donothold)
the
ZI: I_
]i
ON
/ OFF-HOLD
button.
RE-
-_
IL
CHARGE
TONIGHT
flashes
in
REC.A_ _O_.V
the display,
and the softener
be-
gins regeneration
at the next preset
recharge
time.
Press
and release
the ON/OFF-HOLD
button
once
more if you decide
to cancel the regeneration,
and
RECHARGE
TONIGHT.
•
PROGRAM
MEMORY
If electrical
power
to the softener
goes off, the time
display
is blank
but the face plate
timer
keeps
the
correct
time for about
6 hours.
When
electrical
pow-
er comes
on again,
you
have
to reset
the present
time only if the display
is flashing.
The HARDNESS
and RECHARGE
TIME never
require
resetting
un-
less a change
is desired.Even
if the timer is incorrect
after
a long
power
outage,
the softener
works
as it
should
to keep your water
soft. However,
regenera-
tions may
occur at the wrong
time of day until you
reset the timer
to the correct
time of day.
•
RECHARGE
NOW
Press
the ON/OFF-HOLD
but-
ton
and
hold for 3 seconds.
RE-
CHARGE
NOW
begins
to flash
in the display,
and the softener
RECHARGE
NOW
J
enters
the fill cycle of regeneration
right
away. This
regeneration
will last for about
2 hours.
Then,
you
will have
soft water
again.
•
RECHARGE
TONIGHT
•
ERROR
CODE
An error
code
could
appear
in
the face plate
display
if a prob-
lem occurs
in the softener
elec-
tronics.
If you
see an error
code
instead
of the
present
time
of
day,
turn
to
page
5-2
under
"Troubleshooting"
to
resolve
the problem.
IF YOU NEED HELP PROGRAMMING
THE TIMER,
CALL TOLL FREE,
NUMBER
1 - 800 - 426 - 9345.
2-1
Problems,
Questions?
Call
1-800-426-9345
Kenmore
Water
Line