Tools And Materials Needed For Installation; Wiring Diagram - Whirlpool 30” Installation Instructions Manual

L.P. gas conversion
IMPORTANT: All connections must be
wrench-tightened. Do Not make
connections to the gas regulator too tight.
Making the connection too tight may crack
the regulator and cause a gas leak. Do Not
allow the regulator to turn on the pipe
when tightening fittings.
1.P. posltion
\
Natural gas position
\
Converting back to Natural gas
1. Convert the pressure regulator back to
Natural gas by reversing the steps in Step
A, "Pressure regulator".
2. Remove screw located in center of each
burner. Remove LP air shutters from
burners. Replace screws. Save the L-Pair
shutters,
3. Remove L.F?gas orifices (No. 93) and
save. Install Natural gas orifices (No. 155).
Adjusting for proper flame
After all burners have been converted, turn
the gas supply valve back to open position.
Complete steps 9-l 5.
2. Remove cover from cap on top of
regulator, Turn cap over so that L.F! is on
top of cap. Replace cap. Replace cover
over cap.
Electrical Shock Hazard
Disconnect power before converting to
L.P. gas.
Failure to do so can result in death or
electrical shock.
Checking gas pressure
1. Remove right rear burner cap. Connect
an inclined manometer to orifice with a
l/4" I.D. rubber hose. Hold hose tightly to
orifice.
2. Turn two other burners to operate at the
'HI" position. Turn on burner connected
to the manometer, Adjust the gas supply
pressure until the monometer pressure
reading is one-inch water column above
4 for Natural gas and 10 for L.F?gas
pressure. The gas pressure should never
be set below 4 or above 14 inches for
Natural gas and below 10 or above 14
for L.P gas.
gasket
Converting to L.F! gas should be done by a
qualified installer.
Important: Observe all governing codes
and ordinances.
Failure to meet codes and ordinances
could result in risk of fire or electrical shock.
Tools and materials
needed for
installation. 3. Remove cap from top of regulator, Snap
out plastic plunger from bottom of cap.
Turn plunger over so that L-f? is shown on
lower end of plunger and snap back into
cap.
Wiring diagram
N-
TOP IGNITORS
TOP BURNER
IGNITION SWITCHES
L.F! gas-resistant
pipe-joint compound m
,
m-))
7mm nut driver
1. Use nut driver to remove Natural gas
orifices (marked No. 155). Set orifices
aside.
2. Remove L.P orifices (marked No. 93) from
plastic bag attached to bottom of
cooktop. Use nut driver to install L.l?gas
orifices,
Parts supplied for
installation.
burner cap
xz)]
l
4 L.F! alr shutters
l
4
L.P. gas orifices
l
4
screws
SCHEMATIC
Converting to 1-P. gas
Complete steps l-8 before converting your
cooktop to LPgas.
screw -
L TOP BURNER IGNITION SWITCHES
.
B-
air shutter (used
with L.F? gas only)
BLK BLK BLK
BLK
A
w Pressure regulator: The pressure
regulator may be one of three types. Follow
instructions that apply to your type of
regulator.
3. Remove screw located in center of each
burner. Remove L.P air shutters from
plastic bag attached to bottom of
cooktop. Install L.P air shutters. Replace
screws.
4. Save the Natural gas orifices (No. 155),
should the cooktop need to be
converted back to Natural gas.
NOTICE:
1. DISCONNECT RANGE FROM POWER
BEFORE REMOVING WIRE COVER.
2. REFER ONLY TO FEATURES EQUIPPED.
3. SERVICER PLEASE RETURN DIAGRAM
TO RANGE.
1. Push down and turn cap counterclockwise
to remove cap. Turn cap over so that L.P is
on top of cap. Replace cap.
Panel E