Machine-Specific Safety Warnings; Functional Description; Intended Use; Product Features - Bosch PTK 14 E Operating Instructions Manual

OBJ_BUCH-1 609 929 J42-001.book Page 2 Monday, February 6, 2006 7:58 AM
d) Store idle power tools out of the reach of
children and do not allow persons unfamil-
iar with the power tool or these instruc-
tions to operate the power tool. Power tools
are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalign-
ment or binding of moving parts, breakage
of parts and any other condition that may
affect the power tool's operation. If dam-
aged, have the power tool repaired before
use. Many accidents are caused by poorly main-
tained power tools.
f) Keep cutting tools sharp and clean. Prop-
erly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
g) Use the power tool, accessories and tool
bits etc. in accordance with these instruc-
tions, taking into account the working con-
ditions and the work to be performed. Use
of the power tool for operations different from
those intended could result in a hazardous situ-
ation.
5) Service
a) Have your power tool serviced by a quali-
fied repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
Machine-specific
Safety Warnings
B Secure the workpiece. A workpiece clamped
with clamping devices or in a vice is held more
secure than by hand.
B Never use the machine with a damaged cable.
Do not touch the damaged cable and pull the
mains plug when the cable is damaged while
working. Damaged cables increase the risk of an
electric shock.
B Connect machines that are used in the open
via a residual current device (RCD).
B Keep your fingers away from the tacker head
7. There is danger of injury when unintentionally
actuating the On/Off switch.
B Never point the machine at persons or ani-
mals. Staples or nails shot from a short distance
can cause considerable injuries.
B Do not use the machine to fasten electrical
wiring. Contact with electric lines can lead to fire
and electric shock.
1 609 929 J42 • 6.2.06

Functional Description

Read all safety warnings and all
instructions. Failure to follow the warn-
ings and instructions may result in electric
shock, fire and/or serious injury.

Intended Use

The machine is intended for tacking of cardboard, insu-
lating material, fabric, foils, leather and similar materials
on surfaces of wood or materials similar to wood. The
machine is not suitable for the attachment of wall and
ceiling panelling.

Product Features

The numbering of the product features refers to the
illustration of the machine on the graphics page.
1 Trigger
2 Thumbwheel for hammer-force preselection
3 Magazine slider
4 Latching aperture for support foot
5 Latching aperture for spacer clamp
6 Latching aperture for stapler plate
7 Tacker head
8 Duotac automatic selector switch
9 Nail strip*
10 Staple strip*
11 Magazine
12 Support foot*
13 Stapler plate*
14 Spacer clamp*
*Not all of the accessories illustrated or described are
included as standard delivery.

Technical Data

Tacker
Article number
Impact rate
Intermittent operation
Staple width
Staple length
Nails
Magazine capacity, max.
Weight according to
EPTA-Procedure 01/2003
Protection class
The values given are valid for nominal voltages [U] of
230/240 V. For lower voltage and models for specific coun-
tries, these values can vary.
Please observe the article number on the type plate of your
machine. The trade names of the individual machines may
vary.
English–2
PTK 14 E
0 603 265 2..
bpm 30
min 15
mm 11.4
mm 6–14
mm 14
100
kg 1.1
/II