Advertisement
Read and understand these instructions thoroughly before installing
beer dispenser.
ASSEMBLY
1.
Carton Inventory
Unpack and inspect the parts. Make sure all items are present
and in good condition.
1 Draft arm assembly (Package includes 1 gasket for
draft arm and 1 washer for connection to keg tapper)
1 CO2 regulator
1 CO2 cylinder
1 Keg tapper (Sankey type)
1 Cleaning kit
1 Pressure tube
2 Hose clamps
2 Keg supports (wooden plates)
1 CO2 cylinder retainer (spring)
1 Guard rail
1 Drip tray
4 Wheel casters
4 Hex head screws (5mm dia x 15mm long)
16 Machine screws (5mm dia x 12mm long)
8 Small screws (5mm dia x 10mm long)
2.
Install casters
a.
Empty the cabinet and then lay down the beer dispenser
sideways so that the door hingeside comes to the top. Be
careful not to cause dents or scratches on the cabinet.
Placing
outer carton
underneath
the cabinet
is
recommended.
b.
Install casters to the four bottom corners of the cabinet
with the four machine screws (5mm dia x 12mm long) for
each caster.
c.
Stand the cabinet upright.
3.
Install Draft Arm Assembly (See Fig. 1).
a.
Slide gasket over wingnut on bottom of draft arm assem-
bly beer tube. Slide gasket up beer tube to draft arm base.
Hex. Head
Screw
i
I
Draft Arm Assembly
Gasket
•
/
Small Screw
Guard Rail .,_
/
Fig 1.
b.
Push wingnut and beer tube of draft arm assembly
through hole in top of cabinet until draft arm is resting on
cabinet top.
c.
Align holes in draftarm base with holes in gasket and pilot
holes in cabinet top, then secure draft arm to cabinet top
with four hex head screws (5mm dia x 15mm).
4.
Install Guard Rail (See Fig. 1).
a.
Place guard rail on cabinet top and secure guard rail with
eight small screws.
INSTALLATION
"
1.
Install beer dispenser on stronq,,lev_-IftnnLA_ia
direct sun-
light, heatZJb'0_sa_"a_moi-sture. -
2.
Connect to-120Vr-
,
out_et. Do not
use extension cord. Use __q,,_X_tb
three-prong
grounded W'_ff'6"0t1"b
.'t_"_
,
..
,.,
WARNING: Unless the _'d_O_"_gr-_nding
method'Js'io/lowed,
you are not _rotep_=d_,.agaim_-severe 'or lethal
sh0_k in'_h+_'event of a short circuitof an electrical
cq.mponer=Lor_widng of beer dispenser.
TEMPERATURE CONTROL
1.
Controlis located on rear. Firstset the control at NORMAL pos-
ition. Wait for 24 hours to check the temperature then adjust
temperature control, if needed.
DEFROST
1.
Beer dispenser will not require much defrosting since the
door opening is at a minimum. Defrost when V4inch frost is
built up on the cold plate. The best time to defrost is when
the keg is changed. To defrost, set temperature
control at
OFF position and leave door open until ice melts. Defrost
water will accumulate
at the bottom of interior
cabinet
which can be absorbed with a sponge or towel.Do notus6
heating devices or sharp objects to speed defrosting
as this could damage cabinet liner of cold plate. Reset
temperature control after defrosting
is completed.
INSTALLATION
OF BEER SYSTEM
1.
Installing
CO
2
Cylinder
and CO2 Regulator
WARNING:
CO2 GAS CAN BE DANGEROUS
Read front pages of "Draught
Beer Facts" book in-
cluded in your cleaning kit for safety precautions
before installaing the CO2 cylinder.
OPERATING INSTRUCTIONS FOR CO2 CYLINDERS
Do not operate valve control unlesscylinder is completely
installedand connected.
TURN HANDWHEEL
FULLY COUNTERCLOCKWISE
AS FAR AS IT WILL GO-.-
IMPORTANT: If valve is not fullyopened the stem may not
seal properly against the upper packing washer and the
valve may leak. If leak occurswhen fully opened, tighten
down packing nut under handwheel then open and close
valve fully several times. Replacement packing washer
must be ordered directly from valve manufacturer whose
name is stamped on valve.
-2-
Advertisement
