1. Manuals
  2. Brands
  3. IBM Manuals
  4. Server
  5. RS/6000 Enterprise Server M80
  6. Installation manual

IBM RS/6000 Enterprise Server M80 Installation Manual

Hide thumbs Also See for RS/6000 Enterprise Server M80:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Service Manual, User Manual
RS/6000 Enterprise Server Model M80
Eserver pSeries 660 Model 6M1

Installation Guide

SA38-0576-02

Advertisement

Table of Contents
loading

Related Manuals for IBM RS/6000 Enterprise Server M80

Summary of Contents for IBM RS/6000 Enterprise Server M80

  • Page 1: Installation Guide

    RS/6000 Enterprise Server Model M80 Eserver pSeries 660 Model 6M1 Installation Guide SA38-0576-02...
  • Page 2 A reader’s comment form is provided at the back of this publication. If the form has been removed, address comments to Information Development, Department H6DS-905-6C006, 11400 Burnet Road, Austin, Texas 78758-3493. To send comments electronically, use this commercial internet address: aix6kpub@austin.ibm.com. Any information that you supply may be used without incurring any obligation to you.

  • Page 3: Table Of Contents

    Contents Safety Notices. . vii Rack Safety Instructions . . vii Electrical Safety . . viii Laser Safety Information . . ix Laser Compliance . . ix Data Integrity and Verification . . xi About This Book . xiii ISO 9000 .
  • Page 4 Removing a Non-Hot-Pluggable PCI Adapter . . 33 Removing a Hot-Pluggable PCI Adapter . 34 PCI Hot-Plug Manager Access . 37 Accessing Hot-Plug Management Functions . . 37 PCI Hot-Plug Manager Menu . . 37 Chapter 3. Using the Capacity Upgrade on Demand Feature .
  • Page 5 Appendix E. Using the chcod Command . 69 Purpose . . 69 Syntax . 69 Description . . 69 Flags . . 69 Appendix F. General Attributes Required When Using a TTY Terminal . . 71 Additional Communication Attributes . .
  • Page 6 Installation Guide...

  • Page 7: Safety Notices

    Safety Notices A danger notice indicates the presence of a hazard that has the potential of causing death or serious personal injury. Danger notices appear on the following pages: v viii v 27 A caution notice indicates the presence of a hazard that has the potential of causing moderate or minor personal injury.

  • Page 8: Electrical Safety

    Electrical Safety Observe the following safety instructions any time you are connecting or disconnecting devices attached to the workstation. DANGER An electrical outlet that is not correctly wired could place hazardous voltage on metal parts of the system or the devices that attach to the system. It is the responsibility of the customer to ensure that the outlet is correctly wired and grounded to prevent an electrical shock.

  • Page 9: Laser Safety Information

    CAUTION: All IBM laser modules are designed so that there is never any human access to laser radiation above a class 1 level during normal operation, user maintenance, or prescribed service conditions. Data processing environments can contain equipment transmitting on system links with laser modules that operate at greater than class 1 power levels.
  • Page 10 Installation Guide...

  • Page 11: Data Integrity And Verification

    Users should periodically check the IBM support websites for updated information and fixes applicable to the system and related software.
  • Page 12 Installation Guide...

  • Page 13: About This Book

    ISO 9000 registered quality systems were used in the development and manufacturing of this product. Online Publications IBM Eserver pSeries publications are available online. To access the online books, visit our Web site at: http://www.ibm.com/servers/eserver/pseries/library/hardware_docs/ Related Publications The following publications provide additional information about your system unit: v System Unit Safety Information , order number SA23-2652, contains translations of safety information used throughout this book.

  • Page 14: Trademarks

    Trademarks The following terms are trademarks of International Business Machines Corporation in the United States, other countries, or both: v AIX v RS/6000 v pSeries v e (logo) Other company, product, and service names may be trademarks or service marks of others.

  • Page 15: Chapter 1. Setting Up The System

    Chapter 1. Setting Up the System The RS/6000 Enterprise Server Model M80 and Eserver pSeries 660 Model 6M1 are designed to be set up and installed by a certified service representative. Follow the procedures in this chapter to set up the system. Step 1.

  • Page 16: Step 2. Observe Safety Notices

    Step 2. Observe Safety Notices Observe these safety notices during installation. DANGER An electrical outlet that is not correctly wired could place hazardous voltage on metal parts of the system or the devices that attach to the system. It is the responsibility of the customer to ensure that the outlet is correctly wired and grounded to prevent an electrical shock.

  • Page 17: Step 3. Checking The Customer Environment

    Step 3. Checking the Customer Environment Check the customer environment as follows: v Verify with your installation planning representative or the customer that any station-protector boxes used are correctly installed according to the Site and Hardware Planning Information manual. v Make sure the customer is aware that the recommended temperature for this system is 24°...

  • Page 18: Step 4. Checking Customer Outlets

    Step 4. Checking Customer Outlets Check the power outlets before installing the system. CAUTION: Do not touch the receptacle or the receptacle faceplate with anything other than your test probes before you have met the requirements in step 8. This system may be configured for 220 V ac or -48 V dc power. If the system is going to be used in a dc environment, you will need to have dc power cables and a dc power supply.
  • Page 19 __ 8. Verify that the grounding impedance is correct by using the ECOS 1020, 1023, B7106, or an appropriately approved ground impedance tester. Chapter 1. Setting Up the System...

  • Page 20: Step 5. Setting Up Rails In The Rack

    Step 5. Setting Up Rails in the Rack If your system arrived installed in a rack with all the cables attached, skip to “Step 8. Setting Up Attached Devices” on page 24. If not, continue with this step. Note: Read the following drawer-placement notes and caution statements before installing the system rails.
  • Page 21 System unit with System unit with One I/O Drawer Two I/O Drawers CEC Drawer CEC Drawer (8 EIA Units) (8 EIA Units) Primary Primary I/O Drawer I/O Drawer (5 EIA Units) (5 EIA Units) Secondary I/O Drawer (Optional) (5 EIA Units) CAUTION: The stabilizer must be firmly attached to the bottom front of the rack to prevent the rack from turning over when the drawers are pulled out of the rack.
  • Page 22 To set up the rails in the rack, do the following: 1. Determine the EIA locations for the drawer rails. (See the previous figures.) 2. Assemble the drawer rails as follows: a. Use two screws to attach an anti-tip guide (2) to each rail. b.
  • Page 23 3. Install the rails in the rack unit. As you install the right rail into the rack, install the drawer latch reset bracket above the right rail. Detail A - Left Rail Detail B - Right Rail Detail C - Rear of Left Rail Chapter 1.

  • Page 24: Step 6. Installing Drawers In The Rack

    Step 6. Installing Drawers in the Rack CAUTION: This unit weighs between 32 kg (70.5 pounds) and 55 kg (121.2 pounds). Three persons are required to safely move it. Using less than three persons to move it can result in injury. To install the drawers in the rack, do the following: 1.
  • Page 25 7. Install a drawer stop (2), on each side at the front of the rack to prevent the drawer from sliding out the front. Use six screws (1) and four nut clips (3) to attach the drawer stops. See the following figure. 8.

  • Page 26: Step 7. Connecting The Cables

    Step 7. Connecting the Cables Follow the procedures in this section to connect the cables. For instructions on routing and securing cables, see “Routing and Securing Cables” on page 21. Connecting JTAG and VS/COMM Cables Refer to the following figure to connect the JTAG and VS/COMM cables. CEC Drawer Attached to One I/O Drawer CEC Drawer V/S COMM...

  • Page 27: Connecting Rio And Spcn Cables

    Connecting RIO and SPCN Cables The RIO and SPCN cables provide two functions in the system: remote data bus connection and power control. The following rules must be followed when connecting these two types of cables: v The I/O drawers must be connected in a loop fashion for both the RIO cables and the SPCN cables.
  • Page 28 CEC Drawer Attached to One I/O Drawer CEC Drawer Primary Drawer CEC Drawer Attached to Two I/O Drawers Type A CEC Drawer Secondary I/O Drawer Primary I/O Drawer Installation Guide...
  • Page 29 CEC Drawer Attached to Three I/O Drawers CEC Drawer Secondary I/O Secondary I/O Drawer Drawer Primary I/O Drawer Chapter 1. Setting Up the System...
  • Page 30 CEC Drawer Attached to Four I/O Drawers CEC Drawer Secondary I/O Secondary I/O Drawer Drawer Secondary I/O Primary I/O Drawer Drawer Installation Guide...
  • Page 31 SPCN Cabling The following figures provide cabling examples for all valid cabling configurations. Match your configuration to the appropriate figure and connect your SPCN cables as shown. CEC Drawer Attached to One I/O Drawer CEC Drawer VS/COMM Primary I/O Drawer VS/COMM Note: The V/S COMM cable incorporates SPCN wiring.
  • Page 32 CEC Drawer Attached to Two I/O Drawers CEC Drawer V/S COMM Primary I/O Drawer V/S COMM Secondary I/O Drawer Installation Guide...
  • Page 33 CEC Drawer Attached to Three I/O Drawers CEC Drawer V/S COMM Primary I/O Drawer V/S COMM Secondary I/O Drawer Secondary I/O Drawer Chapter 1. Setting Up the System...
  • Page 34 CEC Drawer Attached to Four I/O Drawers CEC Drawer V/S COMM Primary I/O Drawer V/S COMM Secondary I/O Drawer Secondary I/O Drawer Secondary I/O Drawer Installation Guide...

  • Page 35: Routing And Securing Cables

    Routing and Securing Cables To route and secure the cables, use the following descriptions. I/O Drawer Cables: Use two screws (2) to connect the RIO drawer cables to the I/O drawer and secure the cables with the RIO cable retainer (3). Use the cable hanging brackets (1) as needed to hold the cables.
  • Page 36 CEC Drawer Cables: Route the CEC drawer cables toward the right rack rail, and secure the cables with Velcro strips (1). Use the cable hanging brackets (2) as needed to hold the cables. Installation Guide...
  • Page 37 Securing Drawer Cables: Route the cables over the cable guides (2), and secure the cables with Velcro strips (1). Leave a loop that is large enough so that the drawer can be pulled out the back. Chapter 1. Setting Up the System...

  • Page 38: Step 8. Setting Up Attached Devices

    Step 8. Setting Up Attached Devices Note: During the setup of each device, connect only the device end of the signal cable. Do not connect the device signal cables to the rack now. Perform the setup procedures for each device being attached to the rack. (Refer to the documentation provided with each device.) Then return to “Step 9.

  • Page 39: Step 11. Connecting The Power

    If the AIX operating system was preinstalled on your system, go to the AIX System Management Guide: Operating System and Devices . This publication is available at the following Web address: http://www-1.ibm.com/servers/aix/library/. Select Technical Publications.AIX documentation is also located on the AIX Documentation CD. The documentation information is made accessible by loading the documentation CD onto the hard disk or by mounting the CD in the CD-ROM drive.

  • Page 40: Step 16. Verifying The Hardware Operation

    To access the hardware documentation on the Web, go to: http://www.ibm.com/servers/eserver/pseries/library/hardware_docs Installation, Using, and Service documentation is available from this Web site. To order printed versions of the books that are available in hardcopy, go to: http://www.ibm.com/shop/publications/order...

  • Page 41: Chapter 2. Installing Options In Your System

    Chapter 2. Installing Options In Your System This chapter provides instructions to help you add options to your system. Some option-removal instructions are provided, in case you need to remove one option to install another. If you have several internal options to install, these instructions enable you to add them all at one time.

  • Page 42: Handling Static-Sensitive Devices

    Handling Static-Sensitive Devices Attention: Adapters, planars, diskette drives, and disk drives are sensitive to static electricity discharge. These devices are wrapped in antistatic bags to prevent this damage. Take the following precautions: v If an antistatic wrist strap is available, use it while handling the device. v Do not remove the device from the antistatic bag until you are ready to install the device in the system unit.

  • Page 43: I/O Drawer Pci Slot Led Definitions

    I/O Drawer PCI Slot LED Definitions The following table describes the possible states of the LEDs associated with the I/O drawer PCI slots. These LEDs are located at the rear of the I/O drawer. One LED is associated with each PCI slot. Slot LED Indication PCI Slot State...

  • Page 44: Installing Capacity Upgrade On Demand

    Installing Capacity Upgrade on Demand Capacity Upgrade on Demand is a flexibility option for your system that allows increased processor capacity when you want it. You can order the feature on a new system, or add it to an installed system to ensure that you have additional processing power available if you need it.

  • Page 45: Installing A Non-Hot-Pluggable Pci Adapter

    Installing a Non-Hot-Pluggable PCI Adapter To install the non-hot-pluggable adapter, perform the following steps: 1. Turn off the power and unplug the system unit power cable from the electrical outlet. If the system is operating under AIX, type shutdown to power off the system. If you cannot use this method, you can power off the system by using the following operator panel power-button procedure.

  • Page 46: Installing A Hot-Pluggable Pci Adapter

    10. Connect appropriate cables to the adapter. 11. Install the covers that you removed earlier, and return the drawer to the normal operating position. 12. Plug in the system unit power cables. 13. Turn on the power. Installing a Hot-Pluggable PCI Adapter Note: If you have more than one I/O drawer, determine into which drawer you will install the adapter.

  • Page 47: Removing Pci Adapters

    10. Lower the plastic stop over the adapter bracket and rotate the locking latch clockwise until it clicks into the locked position. Some full-length cards can be supported by rotating the blue adapter latch on the right end of the adapter counterclockwise.

  • Page 48: Removing A Hot-Pluggable Pci Adapter

    When the power-off sequence is complete, the system will go into standby mode, as evidenced by: v OK appears in the primary operator panel display. v The primary I/O drawer operator panel LED will start blinking at a slow rate. v The CEC drawer power LED will start blinking at a slow rate.
  • Page 49 AIX System Management Guide: Operating System and Devices . This publication is available at the following Web address: http://www-1.ibm.com/servers/aix/library/. Select Technical Publications. AIX documentation is also located on the AIX Documentation CD. The documentation information is made accessible by loading the documentation CD onto the hard disk or by mounting the CD in the CD-ROM drive.
  • Page 50 18. If you are not replacing the adapter with an identical adapter, place a blank slot cover in the adapter slot and then lower the plastic stop over the adapter bracket. Otherwise, insert the new adapter and rotate the locking latch clockwise until it clicks into the locked position.

  • Page 51: Pci Hot-Plug Manager Access

    AIX System Management Guide: Operating System and Devices . This publication is available at the following Web address: http://www-1.ibm.com/servers/aix/library/. Select Technical Publications.AIX documentation is also located on the AIX Documentation CD. The documentation information is made accessible by loading the documentation CD onto the hard disk or by mounting the CD in the CD-ROM drive.
  • Page 52 Add a PCI Hot-Plug Adapter Allows the user to add a new PCI hot-plug-capable adapter to the slot with the system turned on. You will be asked to identify the PCI slot that you have selected prior to the actual operation. The selected PCI slot will go into the action state and finally into the on state.
  • Page 53 Install/Configure Devices Added After IPL The system attempts to configure any new devices and tries to find and install any required software from a user-selected source. The add, remove, and replace functions return information to the user indicating whether the operation was successful. If additional instructions are provided on the screen, complete the recommended actions.
  • Page 54 Installation Guide...

  • Page 55: Chapter 3. Using The Capacity Upgrade On Demand Feature

    Chapter 3. Using the Capacity Upgrade on Demand Feature The Capacity Upgrade on Demand feature allows a new system to be ordered with extra processor capacity that can be enabled by the system administrator. Also, if a system that is already in use requires additional processor capacity, the system can be upgraded with additional capacity that can be enabled by the system administrator anytime additional capacity is required.

  • Page 56: Process Flow For Capacity Upgrade On Demand

    Process Flow for Capacity Upgrade on Demand The following flowchart provides an overview of the process that is required to enable Capacity Upgrade on Demand on systems that need reserve capacity. Capacity Upgrade on Demand System is ordered with Capacity feature is ordered for upgrade to Upgrade on Demand feature customer system...

  • Page 57: Installing A System With The Capacity Upgrade On Demand Feature

    Installing a System with the Capacity Upgrade on Demand Feature If you are installing a system that was ordered with a processor Capacity Upgrade on Demand feature, continue with this section to install the Capacity Upgrade on Demand feature. If the Capacity Upgrade on Demand feature is already installed in your system and you want to upgrade to use additional processors, go to “Enabling Additional Capacity Upgrade on Demand Processors”...
  • Page 58 Current CustInfo _______________________ Current Model and System ID = IBM, xxxx-______IBM, ________ Current number of authorized proc(s) out of (xx_____) installed on system = (yy_____) where (xx) is the number of processors installed in the system, (yy) is the number of Capacity Upgrade on Demand-enabled processors.

  • Page 59: Enabling The Capacity Upgrade On Demand Feature

    Current MailAddress _______Reserved________ Current CustInfo Jane_Doe-CustomerNumber_9999999-Phone_(333)_444-5555 Current Model and System ID = IBM, xxxx-xxx_IBM,xxxxxxx Current number of authorized proc(s) out of (xx_____) installed on system = (0) 3. Type the following at the command line: chcod -r proc -n total_number_of_processors where the total_number_of_processors is equal to the value of (yy) recorded in step 2 on page 44.
  • Page 60 Current CustInfo Jane_Doe-CustomerNumber_9999999-Phone_(333)_444-5555 Current Model and System ID = IBM, xxxx-xxx_IBM,xxxxxxx Current number of authorized proc(s) out of (xx_____) installed on system = (yy_____) The values of (xx) and (yy) should match the values recorded in step 2 on page 44.

  • Page 61: Enabling Additional Capacity Upgrade On Demand Processors

    Current MailAddress _______Reserved________ Current CustInfo Jane_Doe-CustomerNumber_9999999-Phone_(333)_444-5555 Current Model and System ID = IBM, xxxx-xxx_IBM,xxxxxxx Current number of authorized proc(s) out of (xx_____) installed on system = (yy_____) The values of (xx) and (yy) are the current values for the number of processors installed (xx) and the number of authorized processors (yy).

  • Page 62: Adding Processor Capacity

    Current MailAddress _______Reserved________ Current CustInfo Jane_Doe-CustomerNumber_9999999-Phone_(333)_444-5555 Current Model and System ID = IBM, xxxx-xxx_IBM,xxxxxxx Current number of authorized proc(s) out of (xx_____) installed on system = (yy_____) The values of (yy) should match the value you entered for the total_number_of_processors in step 1.

  • Page 63: Chapter 4. Verifying The Hardware Operation

    Chapter 4. Verifying the Hardware Operation The system verification procedure checks the system for correct hardware operation. If you have a problem with your system in the future, use this procedure to test the system hardware to help you determine if you have a hardware problem. Run the system verification procedure as described in the following steps.

  • Page 64: Step 4. Performing Additional System Verification

    3. Select the System Verification option on the Diagnostic Mode Selection menu. 4. To run a general checkout of all installed resources, select the All Resource option on the Diagnostic Selection menu. Follow the instructions on the screen to complete the checkout procedure.

  • Page 65: Step 5. Stopping The Diagnostics

    Step 5. Stopping the Diagnostics To stop the diagnostics, do the following: 1. To exit the diagnostics, press the F3 key (from a defined terminal) or press 99 (from an undefined terminal). 2. If you changed any attributes on your ASCII terminal to run the diagnostics, change the settings back to normal.
  • Page 66 Installation Guide...

  • Page 67: Appendix A. Communications Statements

    Appendix A. Communications Statements The following statement applies to this product. The statement for other products intended for use with this product appears in their accompanying documentation. Federal Communications Commission (FCC) Statement Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.

  • Page 68: International Electrotechnical Commission (Iec) Statement

    International Electrotechnical Commission (IEC) Statement This product has been designed and built to comply with IEC 60950. United Kingdom Telecommunications Safety Requirements This equipment is manufactured to the International Safety Standard EN60950 and as such is approved in the UK under the General Approval Number NS/G/1234/J/100003 for indirect connection to the public telecommunication network.

  • Page 69: Electromagnetic Interference (Emi) Statement - Taiwan

    Dieses Gerät ist berechtigt in Übereinstimmung mit Dem deutschen EMVG vom 9.Nov.92 das EG–Konformitätszeichen zu führen. Der Aussteller der Konformitätserklärung ist die IBM Germany. Dieses Gerät erfüllt die Bedingungen der EN 55022 Klasse A. Für diese von Geräten gilt folgende Bestimmung nach dem EMVG: Geräte dürfen an Orten, für die sie nicht ausreichend entstört sind, nur mit besonderer...
  • Page 70 Installation Guide...

  • Page 71: Appendix B. Environmental Notices

    Recycling facilities may not be available in your area. For information on disposal of batteries, contact your local waste disposal facility. In the United States, IBM has established a collection process for reuse, recycling, or proper disposal of used IBM sealed lead acid, nickel cadmium, nickel metal hydride, and other battery packs from IBM Equipment.
  • Page 72 Installation Guide...

  • Page 73: Appendix C. Notices

    Appendix C. Notices This information was developed for products and services offered in the U.S.A. The manufacturer may not offer the products, services, or features discussed in this document in other countries. Consult the manufacturer’s representative for information on the products and services currently available in your area. Any reference to the manufacturer’s product, program, or service is not intended to state or imply that only that product, program, or service may be used.
  • Page 74 Installation Guide...

  • Page 75: Appendix D. System Records

    Appendix D. System Records Record the Identification Numbers Record and retain the following information. Product Name: ____________________________ CPU Type/Speed: ____________________________ Serial Number: ____________________________ ____________________________ The identification numbers for the system are located on the front cover and on the rear of the system, as shown in the following figures: CEC Serial Number I/O Drawer Serial Number...

  • Page 76: Device Records

    Device Records Use the following tables to keep a record of the options installed in or attached to your system. This information can be helpful when you install additional options in your system or if you ever need to have your system serviced. Memory Riser Card 1 128MB( ) 256MB( ) 512MB( ) 1GB( ) 128MB( ) 256MB( ) 512MB( ) 1GB( )

  • Page 77: Memory Riser Card 2

    Memory Riser Card 2 128MB( ) 256MB( ) 512MB( ) 1GB( ) 128MB( ) 256MB( ) 512MB( ) 1GB( ) 128MB( ) 256MB( ) 512MB( ) 1GB( ) 128MB( ) 256MB( ) 512MB( ) 1GB( ) 128MB( ) 256MB( ) 512MB( ) 1GB( ) 128MB( ) 256MB( ) 512MB( ) 1GB( ) 128MB( ) 256MB( ) 512MB( ) 1GB( ) 128MB( ) 256MB( ) 512MB( ) 1GB( )

  • Page 78: Primary I/O Drawer Records

    Primary I/O Drawer Records Location Option Description Mouse Connector IBM Mouse h Other:____________________________ Keyboard Connector Space Saving h Enhanced h Other:______________ Ethernet Connector ______________________________________________ SCSI Connector ______________________________________________ Expansion Slot 1 ______________________________________________ Expansion Slot 2 ______________________________________________ Expansion Slot 3 ______________________________________________ Expansion Slot 4...

  • Page 79: Secondary I/O Drawer Records

    Location Option Description Expansion Slot 14 ______________________________________________ Parallel Port ______________________________________________ Serial Port 1 ______________________________________________ Serial Port 2 ______________________________________________ Serial Port 3 ______________________________________________ Serial Port 4 ______________________________________________ Secondary I/O Drawer Records Location Option Description SCSI Connector ______________________________________________ Expansion Slot 1 ______________________________________________ Expansion Slot 2 ______________________________________________ Expansion Slot 3...
  • Page 80 Location Option Description Expansion Slot 8 ______________________________________________ Expansion Slot 9 ______________________________________________ Expansion Slot 10 ______________________________________________ Expansion Slot 11 ______________________________________________ Expansion Slot 12 ______________________________________________ Expansion Slot 13 ______________________________________________ Expansion Slot 14 ______________________________________________ Installation Guide...
  • Page 81 Refer to the following diagram of the bays for the system when completing the following table. Bay A1 - Diskette Bay A2 - CD-ROM Bay B1 - Optional Media Notes: 1. If you attach a drive or other device to an adapter, record the expansion-slot number for that adapter in the Adapter field of the following table.
  • Page 82 Installation Guide...

  • Page 83: Appendix E. Using The Chcod Command

    Appendix E. Using the chcod Command Purpose Manages the Capacity Upgrade on Demand feature. Syntax chcod [-r ResourceType -n NbrResource ] [-c CustomerInfo ] [-h] Description The chcod command manages the Capacity Upgrade on Demand feature, which allows configuration of more ResourceType , in this instance processors, on the system than were initially configured.
  • Page 84 -r ResourceType Specifies the ResourceType (proc for processors) to be enabled and monitored on the system. The system must support Capacity Upgrade on Demand for ResourceType . If -r is specified, then -n must also be specified. The default for the chcod command (with no flags) displays the current value of CustomerInfo , a reserved field named MailAddr , the system’s model name and serial number, and the current values for any ResourceType .

  • Page 85: Appendix F. General Attributes Required When Using A Tty Terminal

    Appendix F. General Attributes Required When Using a TTY Terminal The following general attributes are the default settings for the diagnostic programs. Be sure your terminal is set to these attributes. Note: Set these attributes before the diagnostic programs are loaded. General Setup 3151 3151...

  • Page 86: Additional Communication Attributes

    General Setup 3151 3151 3161 /3164 Description Attributes /11/31/41 /51/61 Settings Settings Settings Line wrap The cursor moves to the first character position of the next line in the page after it reaches the last character position of the current line in the page. Forcing insert Field Field...

  • Page 87: Additional Keyboard Attributes

    Communication 3151/11 3151 3161 /3164 Description Setup Attributes /31/41) /51/61, Settings Settings Settings Turnaround character Selects the carriage return (CR) character as the line turnaround character. Interface EIA-232 EIA-232 EIA-232 Uses the EIA-232 interface protocol. Line control IPRTS IPRTS IPRTS Uses the ’permanent request to send’...

  • Page 88: Additional Printer Attributes

    Additional Printer Attributes The following printer attributes are for a printer attached to the 3151, 3161, and 3164 terminals. Printer Setup 3151/11 3151 3161 /3164 Description Attributes /31/41 /51/61 Settings Settings Settings Line speed 9600 9600 9600 Uses 19200 or 9600 bps (bits per second) line speed to communicate with the system unit.

  • Page 89: Index

    Index about this book xiii emissions accessing documentation 26 noise 57 hardware 26 operating system 26 handling static-sensitive devices 28 acoustical hot-pluggable options 32 noise hot-pluggable PCI adapter installation procedures 37 emissions 57 adapters 30 AIX operating system documentation 25, 35, 37 installation, system 1 attributes required for TTY terminal 71 installing 10...
  • Page 90 rail installation 6 records, device 62 records, system 61 recycling 57 related publications xiii removing PCI adapters 33 RIO cabling 13 routing and securing cables 21 safety considerations 27 electrical viii installation 2 laser compliance statement ix rack vii safety notices vii set up attached devices 24 slot LEDs 29 SPCN cabling 13...
  • Page 91 Thank you for your responses. May we contact you? h Yes h No When you send comments to IBM, you grant IBM a nonexclusive right to use or distribute your comments in any way it believes appropriate without incurring any obligation to you. Name...
  • Page 92 Readers’ Comments — We’d Like to Hear from You Cut or Fold Along Line SA38-0576-02 Fold and Tape Please do not staple Fold and Tape _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ NO POSTAGE NECESSARY IF MAILED IN THE...
  • Page 94 Part Number: 09P4388 Printed in U.S.A. September 2001 SA38-0576-02...

This manual is also suitable for:

Eserverpseries 660 6m1Eserver p series 660 6m1

Table of Contents