Page 1 Toshiba Personal Computer Satellite P100 Series Maintenance Manual TOSHIBA CORPORATION File Number 960-Q02...
Page 2 The information presented in this manual has been reviewed and validated for accuracy. The included set of instructions and descriptions are accurate for the Satellite P100 Series at the time of this manual's production. However, succeeding computers and manuals are subject to change without notice.
Page 3 NOTE: “Note” contains general information that relates to your safe maintenance service. Improper repair of the computer may result in safety hazards. Toshiba requires service technicians and authorized dealers or service providers to ensure the following safety precautions are adhered to strictly.
Page 4 The manual is divided into the following parts: Chapter 1 Hardware Overview describes the Satellite P100 system unit and each FRU. Chapter 2 Troubleshooting Procedures explains how to diagnose and resolve FRU problems. Chapter 3 Test and Diagnostics describes how to perform test and diagnostic operations for maintenance service.
Page 5 Conventions This manual uses the following formats to describe, identify, and highlight terms and operating procedures. Acronyms On the first appearance and whenever necessary for clarification acronyms are enclosed in parentheses following their definition. For example: Read Only Memory (ROM) Keys Keys are used in the text to describe many operations.
Page 6: Table Of Contents
Table of Contents Chapter 1 Hardware Overview Features ..........................1 System Block Diagram ....................7 2.5-inch Hard Disk Drive.....................11 Optical Drive........................16 1.4.1 DVD-ROM & CD-R/RW Drive.............16 1.4.2 DVD Super Multi Drive.................21 Keyboard........................27 TFT Color Display.......................28 1.6.1 LCD Module ..................28 1.6.2 FL Inverter Board...................29 Power Supply .......................30 Batteries ........................32 1.8.1...
Page 7 Procedure 1 Message Check ............... 14 Procedure 2 Debugging Port Check............16 Procedure 3 Diagnostic Test Program Execution Check ......21 Procedure 4 Replacement Check ..............21 USB FDD Troubleshooting ..................22 Procedure 1 FDD Head Cleaning Check ............ 22 Procedure 2 Diagnostic Test Program Execution Check ......
Page 8 Display Troubleshooting....................35 Procedure 1 External Monitor Check............35 Procedure 2 Diagnostic Test Program Execution Check ......35 Procedure 3 Connector and Cable Check ............36 Procedure 4 Replacement Check ..............37 2.10 Optical Disk Drive Troubleshooting................38 Procedure 1 Diagnostic Test Program Execution Check ......38 Procedure 2 Connector Check and Replacement Check......38 2.11...
Page 9 Chapter 3 Test Program for Field Tests and Diagnostics Software Overview ..............3-3 Executing the Diagnostic Test ................... 3-4 Subtest names......................3-8 System Test......................3-11 Memory Test......................3-13 Keyboard Test......................3-16 Display Test ......................3-19 Floppy Disk Test...................... 3-34 Hard Disk Test ......................3-36 3.10 Real Time Clock Test ....................
Page 10 3.21.1 How to operate a window …………………………………………3-62 3.21.2 How to Stop the Test Program ……………………………………. 3-62 3.21.3 Test Status Screen …………………………………………………3-62 3.21.4 Test Stop Display……………………………………………………3-64 3.21.5 How to enter data ……………………………………………………….. 3-64 Chapter 4 Replacement Procedures Overview........................4-1 Safety Precautions ....................4-2 Before You Begin ....................
Page 11 4.18 CPU..........................4-47 4.19 VGA heat sink......................4-50 4.20 LCD unit / FL inverter ..................... 4-52 Satellite P100 Maintenance Manual (960-Q02)
Page 12 Appendices Appendix A Handling the LCD Module ................A-1 Appendix B Board Layout ....................B-1 Appendix C Pin Assignments.....................C-1 Appendix D Keyboard Scan/Character Codes ..............D-1 Appendix E Key Layout.....................E-1 Appendix F Wiring Diagrams.................... F-1 Appendix G BIOS Rewrite Procedures ................G-1 Appendix H EC/KBC Rewrite Procedures................
Page 13 Satellite P100 Maintenance Manual (960-Q02)
Page 14: Chapter 1 Hardware Overview
Chapter 1 Hardware Overview...
Page 15 Chapter 1 Hardware Overview Hardware Overview Satellite P100 Maintenance Manual(960-Q02)
Page 16 Hardware Overview Chapter 1 Chapter 1 Contents Features ..........................1 System Block Diagram ....................7 2.5-inch Hard Disk Drive.....................11 Optical Drive........................16 1.4.1 DVD-ROM & CD-R/RW Drive ............16 1.4.2 DVD Super Multi Drive.................21 Keyboard........................27 TFT Color Display.......................28 1.6.1 LCD Module ..................28 1.6.2 FL Inverter Board...................29 Power Supply .......................30 Batteries ........................32 1.8.1...
Page 17 Chapter 1 Hardware Overview Figures Figure 1-1 Front of the computer and the system units configuration ........6 Figure 1-2 System block diagram..................7 Figure 1-3 2.5-inch HDD....................11 Figure 1-4 DVD-ROM & CD-R/RW drive ...............16 Figure 1-5 DVD Super Muti drive..................21 Figure 1-6 Keyboard......................27 Figure 1-7 LCD module.....................28...
Page 18: Features
Chapter 1 Hardware Overview Features Features The Satellite P100 (Intel Platform) series are 2 spindle PCs running Intel® Celeron® M Processor 410 or higher. Intel® Core™ Solo Processor T1300 or higher. Intel® Core™ Duo Processor T2300 or higher. The features are listed below. θ...
Page 19 The 4-pin S-Video port is compatible with PAL or NTSC TV standard. Digital Video Interface port supported θ Keyboard Toshiba Standard keyboard with 103 keys (desktop-style), Support Windows keys & Application keys. (Toshiba standard layout) Standard pitch, 2.5mm travel length. Multi-langue support...
Page 20 Chapter 1 Hardware Overview θ PC card slot The PC card slot (PCMCIA) accommodates one 5mm Type II card. The slot support 16-bit PC cards and Card Bus PC cards. Card Bus supports 32-bit PC cards. θ Optical devices A DVD-ROM & CD-R/RW drive or DVD Super Multi drive is equipped. θ...
Page 21 Chapter 1 Hardware Overview θ Express Card ExpressCard/34 and ExpressCard/54 are supported. θ Multiple Digital Media Card Slot MD/MS/MS pro/SDIO/MMC are supported θ Bluetooth USB Bluetooth Module (BTO) V2.0 & EDR(Enhanced Data Rate) equipped θ Security Kensington Lock, Fingerprint –Enhanced Lock is also equipped. Satellite P100 Maintenance Manual(960-Q02)
Page 22 Chapter 1 Hardware Overview Satellite P100 Maintenance Manual (960-Q02)
Page 23: Figure 1-1 Front Of The Computer And The System Units Configuration
Chapter 1 Hardware Overview Figure 1-1 Front of the computer and the system units’ configuration Satellite P100 Maintenance Manual(960-Q02)
Page 24: System Block Diagram
Chapter 1 Hardware Overview System Block Diagram Figure 1-2 shows the system block diagram. Figure 1-2 System block diagram for Intel Platform Platform Satellite P100 Maintenance Manual (960-Q02)
Page 25 Chapter 1 Hardware Overview The PC contains the following components. θ CPU Intel Core Duo T2300(1.66GHz) T2400(1.83GHz), T2500 (2GHz), T2600(2.16Gz) , T2700(2.33Gz) Intel Core Solo T1400(1.83GHz) T1300 (1.66GHz) FSB : 667MHz Intel Celeron-M (Yonah core based) FSB 533MHz θ Memory Two memory slots capable of accepting DDRII-SDRAM 256MB, 512MB or 1GB memory modules for a maximum of 4GB.
Page 26 Chapter 1 Hardware Overview • South Bridge (Intel 82801GBM (ICH7-M)) − PCI slot − PCI Express − IDE controller − Serial ATA Host Controller − DMA controller − USB host interface − USB 2.0 host controller − UHCI host controller −...
Page 27 Chapter 1 Hardware Overview θ Mini Card Wireless LAN card (BTO) 2.4GHz DSSS/OFDM LAN card is equipped. Conformity with IEEE 802.11b/g and IEEE 802.11a/b/g.. Transfer speed maximum is 54Mbit/sec. supports 128bit WEP. θ LAN (Intel) Controls LAN. Intel EP82562T (Ekron) supports 10/100M LAN Intel 82573L (Vidalia) supports GigaLan.
Page 28: Inch Hard Disk Drive
A compact, high-capacity HDD with a height of 9.5mm. Contains a 2.5-inch magnetic disk and magnetic heads. Figure 1-3 shows a view of the 2.5-inch HDD and Tables 1-1 and 1-2 list the specifications. Figure 1-3 2.5-inch HDD Table 1-1 2.5-inch HDD dimensions Standard value TOSHIBA TOSHIBA TOSHIBA TOSHIBA TOSHIBA Parameter...
Page 29: Table 1-2 2.5-Inch Hdd Specifications
HITACHI HTS721060G9AT00 HTS721080G9AT00 HTS721010G9AT00 69.85 Width (mm) Outline Height(mm) dimensi 100.2 Depth (mm) 115 Max Weight (g) Table 1-2 2.5-inch HDD specifications Specification Toshiba Toshiba Toshiba Toshiba Toshiba Parameter MHV2100 MK1032G MK8032G MK6032G MK4032GS Storage size (formatted) 120GB 100GB 80GB...
Page 30 Chapter 1 Hardware Overview Specification Parameter FUJITSU FUJITSU FUJITSU FUJITSU FUJITSU FUJITSU MHV2120B MHV2100B MHV2080B MHV2060B MHV2040B MHV2160BT Storage size 120GB 100GB 80GB 60GB 40GB 160GB (formatted) Speed (RPM) 5,400 4,200 Data transfer speed 236.1~ 465.0 218~ 429 218~ 429 218~ 429 150 (Max).
Page 31 Chapter 1 Hardware Overview Specification Parameter HITACHI HITACHI HITACHI HITACHI HTS541040G9SA HTS541040G9S HTS541040G9 HTS541040G9S SA00 Storage size (formatted) 40GB 60GB 80GB 100GB Speed (RPM) 5,400 Data transfer speed(Mbits/s) bus transfer rate (MB/s) 150 ATA7/SERIAL ATA1.0a/Serial ATAII 1.2 interface support Buffer Size 8192 8192 8192...
Page 32 Chapter 1 Hardware Overview Specification HITACHI HITACHI HITACHI Parameter HTS721060G9AT00 HTS721080G9AT00 HTS721010G9AT00 Storage size (formatted) 60GB 80GB 100GB Speed (RPM) 7,200 267-629 Data transfer speed(Mbits/s) bus transfer rate (MB/s) 150 ATA7/SERIAL ATA1.0a/Serial ATAII 1.2 interface support Buffer Size 16385 16385 16385 Track /mm density (TPI) 117,210,240...
Page 33: Optical Drive
Chapter 1 Hardware Overview Optical Drive 1.4.1 DVD-ROM & CD-R/RW Drive The DVD-ROM & CD-R/RW drive accommodates either 12 cm (4.72-inch) or 8 cm (3.15- inch) CD/DVD-ROM and CD-R/RW. It is a high-performance drive that reads DVD at maximum 8-speed and CD at maximum 24-speed. The DVD-ROM &...
Page 34: Table 1-4 Dvd-Rom & Cd-R/Rw Drive Specifications
Chapter 1 Hardware Overview Table 1-4 DVD-ROM & CD-R/RW drive specifications (1/3) Drive Specification Parameter MATSUSHITA (UJDA770TT-A) DVD-ROM MAX 8X CAV (MAX 10800 KB/s) Read (KB/s) CD-ROM MAX 24X CAV (MAX 3600 KB/s) CD-R 4X , 8X (CLV), 16XZCLV, MAX. 24X(CAV) CD-RW 4X (CLV) Data transfer...
Page 35 Chapter 1 Hardware Overview Table 1-4 DVD-ROM & CD-R/RW drive specifications (2/3) Drive Specification Parameter HLDS (GCC-4244N.ATAKN0) DVD-ROM Single Layer3.3x -8x (CAV):Approx. 4,710 r/min Dual Layer3.3x -8x (CAV): Approx. 5,180 r/min DVD-Video 1.7x -4x (CAV): Approx. 2,600r/min DVD-R 3.95GB1.7x -4x (CAV): Approx. 2,600 r/min 4.7GB1.7x -4x (CAV): Approx.
Page 36 Chapter 1 Hardware Overview CD-ROM Mode1&2S CD-ROM XA Modo2 (Form1&2) CD-DA, CD-I, CD-Extra/CD-Plus, Video-CD DVD-ROM Supported disk DVD Video format DVD-R (General, Authoring) DVD-RW (Single/Multi-boarder, Packet) DVD-RAM DVD+R/RW Satellite P100 Maintenance Manual (960-Q02)
Page 37 Chapter 1 Hardware Overview Table 1-4 DVD-ROM & CD-R/RW drive specifications (3/3) Drive Specification Parameter TSST (TS-L462C/TOHJ,I.) CD-ROM Max. 24X (3,600 KB/sec) CAV 24X CD-RW Max. 24X (3,600 KB/sec) CAV 24X DVD-Single Max 8X (10,800 KB/sec) Read (KB/s) DVD-Dual Max 6 (10,800 KB/sec) CD-R Max.
Page 38: Dvd Super Multi Drive
Chapter 1 Hardware Overview 1.4.2 DVD Super Multi Drive The DVD Super Multi drive accommodates either 12 cm (4.72-inch) or 8 cm (3.15-inch) CD/DVD-ROM, CD-R/RW, DVD±R/±RW and DVD-RAM. It is a high-performance drive that reads DVD-ROM at maximum 8-speed and CD at maximum 24-speed. Write speed of DVD±R/±RW and DVD-RAM is different depending on the drive.
Page 39: Table 1-6 Dvd Super Multi Drive Specifications
Chapter 1 Hardware Overview Table 1-6 DVD Super Multi drive specifications (1/4) Drive Specification Parameter Panasonic (UJ-850BTJV-A) DVD-ROM MAX 8X CAV (MAX 10800 KB/s) CD-ROM Read(KB/s) MAX 24X CAV (MAX 3600 KB/s) CD-R 4X , 8X (CLV) , MAX. 12x, 16x, 24X (ZCLV) CD-RW 4X (CLV) HS-RW 4X, 8X, 10X (CLV) ,Max.16X...
Page 40 Chapter 1 Hardware Overview Table 1-2 DVD Super Multi drive specifications (2/4) Drive Specification Parameter HLDS (GSA-4082N.ATAKN0) DVD-R/RW/ROM 8x/8x/8x max. DVD-RAM (Ver.1.0)2x (Ver.2.2)2x, 3x, 5x DVD-Video (CSSCompliant Disc)4x max.(Single/Dual layer) Read(KB/s) DVD+R/+RW 8x/8xmax. DVD+R DL4xmax. CD-R/RW/ROM 24x/24x/24x max. CD-DA (DAE) 20x max. DVD-R 2x CLV, 4x ZCLV, 8x CAV DVD-R...
Page 41 Chapter 1 Hardware Overview Table 1-6 DVD Super Multi drive specifications (3/4) Drive Specification Parameter Pioneer(DVR-K16TBA) 8X CAV at DVD-ROM (Single Layer),DVD-R/ RW and +R / RW 6X CAV at DVD-ROM (Dual-Layer), DVD-R DL and +R DL Read(KB/s) 5X Zone CLV at DVD-RAM 24XCAV at CD-ROM andCD-R/ RW 8X Zone CLV at DVD-R / +R and +RW 6X Zone CLV at DVD-RW...
Page 42 Chapter 1 Hardware Overview Table 1-6 DVD Super Multi drive specifications (4/4) Drive Specification Parameter TEAC (DV-W28EA) 8X CAV at DVD-ROM (Single Layer),DVD-R/ +R 4X CAV at DVD-RW/ +RW 4X CAV at DVD+R (Dual Layer), DVD-R DL and +R DL 3X-5X Zone CLV at DVD-RAM Read(KB/s) 24XCAV at CD-ROM...
Page 43 Chapter 1 Hardware Overview Satellite P100 Maintenance Manual(960-Q02)
Page 44: Keyboard
Chapter 1 Hardware Overview Keyboard The Satellite P100 comes with a "desktop-style" keyboard built into it. This means it is full- sized and features a full set of numeric function keys (also known as calculator keys) on the right-hand side. Unlike other notebooks computers with smaller keyboards, there is no 'Numeric Mode' or any numeric keyboard overlay.
Page 45: Tft Color Display
Chapter 1 Hardware Overview TFT Color Display The TFT color display is 17.1 inch and consists of LCD module and FL inverter board. 1.6.1 LCD Module The LCD module used for the TFT color display uses a backlight as the light source and can display with 1,440x 900 dots (WXGA+) or 1,680x1,050 dots(WSXGA+) resolution.
Page 46: Fl Inverter Board
Chapter 1 Hardware Overview 1.6.2 FL Inverter Board The FL inverter board supplies a high frequency current to illuminate the LCD module FL. Table 1-10 lists the FL inverter board specifications. Table 1-8 FL inverter board specifications Specifications Item SUMIDA FL9030 IV002 Input...
Page 47: Power Supply
Chapter 1 Hardware Overview Power Supply The power supply supplies 23 different voltages to the system board. The power supply microcontroller has the following functions. 1. Judges if the DC power supply (AC adapter) is connected to the computer. 2. Detects DC output and circuit malfunctions. 3.
Page 48: Table 1-9 Power Supply Output Rating
Chapter 1 Hardware Overview Table 1-9 Power supply output rating Power supply （Yes/No） Name Voltage Power OFF Power OFF Object Suspend mode Boot mode Battery 1.484 - VCC_CORE 0.748 1.05 CPU, 915GM, ICH4-M +1.8V CPU, 915GM,ICH4-M +1.5V 915GM,ICH4-M +0.9V DDR2-SDRAM +1.8VSUS RC410MB, DDR2-SDRAM +1.5V_S5...
Page 49: Batteries
Chapter 1 Hardware Overview Batteries The PC has the following two batteries. θ Main battery θ Real time clock (RTC) battery Table 1-10 lists the specifications for these two batteries. Table 1-10 Battery specifications Battery Name Battery Element Output Voltage Capacity Sanyo 10.8v...
Page 50: Battery Charging Control
Chapter 1 Hardware Overview 1.8.2 Battery Charging Control Battery charging is controlled by a power supply microprocessor. The power supply microprocessor controls power supply and detects a full charge when the AC adaptor and battery are connected to the computer. θ...
Page 51: Rtc Battery
Chapter 1 Hardware Overview 1.8.3 RTC Battery The RTC battery provides the power supply to maintain the date, time, and other system information in memory. Table 1-13 lists the Time required for charges of RTC battery and data preservation time. Table 1-13 Time required for charges of RTC battery Condition Time...
Page 52: Ac Adapter
Chapter 1 Hardware Overview AC Adapter The AC adapter is used to charge the battery. Table 1-14 lists the AC adapter specifications. Table 1-14 AC adapter specifications Parameter Specification With Led DELTA/ LITE-ON DELTA/ LITE-ON DELTA/LITE-ON Power 120W Input voltage AC 100V/240V AC 100V/240V AC 100V/240V...
Page 53: Troubleshooting Procedures
Chapter 2 Troubleshooting Procedures [CONFIDENTIAL]...
Page 54 [CONFIDENTIAL] Satellite P100 Maintenance Manual(960-Q02)
Page 55 Chapter 2 Contents Troubleshooting ......................1 Troubleshooting Flowchart....................3 Power Supply Troubleshooting..................7 Procedure 1 Power Status Check ..............7 Procedure 2 Error Code Check ..............9 Procedure 3 Connection Check..............10 Procedure 4 Charging Check ...............10 Procedure 5 Replacement Check ..............12 System Board Troubleshooting................... 13 Procedure 1 Message Check ...............
Page 56 [CONFIDENTIAL] Satellite P100 Maintenance Manual(960-Q02)
Page 57 Display Troubleshooting....................35 Procedure 1 External Monitor Check............35 Procedure 2 Diagnostic Test Program Execution Check ......35 Procedure 3 Connector and Cable Check.............36 Procedure 4 Replacement Check ..............37 2.10 Optical Disk Drive Troubleshooting................38 Procedure 1 Diagnostic Test Program Execution Check ......38 Procedure 2 Connector Check and Replacement Check......38 2.11 Modem Troubleshooting....................39...
Page 58 [CONFIDENTIAL] Satellite P100 Maintenance Manual(960-Q02)
Page 59: Troubleshooting
The implement for the Diagnostics procedures is referred to Chapter 3. Also, following implements are necessary: 1. Phillips screwdrivers (For replacement procedures) 2. Implements for debugging port check • Toshiba MS-DOS system FD • RS-232C cross cable • Test board with debug port test cable •...
Page 60 2 Troubleshooting Procedures There are following two types of connections in the figure of board and module connection in and after 2.3 Power Supply Troubleshooting. (1) Cable connection is described in the figure as line. (2) Pin connection is described in the figure as arrow. <e.g.>...
Page 61: Troubleshooting Flowchart
Before going through the flowchart steps, verify the following: Ask him or her to enter the password if a password is registered. Verify with the customer that Toshiba Windows is installed on the hard disk. Non- Windows operating systems can cause the computer to malfunction.
Page 62 2 Troubleshooting Procedures Figure 2-1 Troubleshooting flowchart (1/2) Satellite P100 Maintenance Manual(960-Q02)
Page 63 2 Troubleshooting Procedures Figure 2-1 Troubleshooting flowchart (2/2) Satellite P100 Maintenance Manual (960-Q02)
Page 64 2 Troubleshooting Procedures If the diagnostics program cannot detect an error, the problem may be intermittent. The Test program should be executed several times to isolate the problem. Check the Log Utilities function to confirm which diagnostic test detected an error(s), and then perform the appropriate troubleshooting procedures as follows: 1.
Page 65: Power Supply Troubleshooting
2 Troubleshooting Procedures Power Supply Troubleshooting The power supply controller controls many functions and components. To determine if the power supply is functioning properly, start with Procedure 1 and continue with the other Procedures as instructed. The procedures described in this section are: Procedure 1: Power Status Check Procedure 2: Error Code Check Procedure 3: Connection Check...
Page 66 2 Troubleshooting Procedures Table 2-2 DC IN icon DC IN icon Power supply status Lights green DC power is being supplied from the AC adapter. Blinks orange Power supply malfunction Doesn’t light Any condition other than those above. *1 When the power supply controller detects a malfunction, the DC IN icon blinks orange.
Page 67 2 Troubleshooting Procedures Procedure 2 Satellite P100 Maintenance Manual (960-Q02)
Page 68: Procedure 3 Connection Check
2 Troubleshooting Procedures Procedure 3 Connection Check The wiring diagram related to the power supply is shown below: Any of the connectors may be disconnected. Perform Check 1. Check 1 Make sure the AC adapter and the AC power cord is firmly plugged into the DC IN socket (CN21/34) and wall outlet.
Page 69 2 Troubleshooting Procedures Check 4 The battery’s temperature is too high or low. Leave the battery for a while to adjust it in the right temperature. If the battery pack is still not charged, go to Check 5. Check 5 Replace the battery pack with a new one.
Page 70: Procedure 5 Replacement Check
2 Troubleshooting Procedures Procedure 5 Replacement Check The power is supplied to the system board by the AC adapter. If either the AC adapter or the system board was damaged, perform the following Checks. Replacement To disassemble the computer, follow the steps described in Chapter 4, Procedures When AC adapter is connected;...
Page 71: System Board Troubleshooting
2 Troubleshooting Procedures System Board Troubleshooting This section describes how to determine if the system board is malfunctioning or not. Start with Procedure 1 and continue with the other procedures as instructed. The procedures described in this section are: Procedure 1: Message Check Procedure 2: Debugging Port Check Procedure 3: Diagnostic Test Program Execution Check Procedure 4: Replacement Check...
Page 72: Procedure 1 Message Check
2 Troubleshooting Procedures Procedure 1 Message Check When the power is turned on, the system performs the Power On Self Test (POST) installed in the BIOS ROM. The POST tests each IC on the system board and initializes it. If an error message is shown on the display, perform Check 1. If there is no error message, go to Procedure 2.
Page 73 2 Troubleshooting Procedures Check 3 The IRT checks the system board. When the IRT detects an error, the system stops or an error message appears. If one of the following error messages (1) through (17), (24) or (25) is displayed, go to Procedure 4.
Page 74: Debugging Port Check
2 Troubleshooting Procedures Procedure 2 Debugging Port Check Check the MiniPCI Debug board. The tool for debug port test is shown below. Figure 2-2 A set of tool for debug port test The test procedures are follows: 1. Replace Mini PCI debug port with Wireless LAN card, check LED in the Mini PCI debug board The following is a list of the Test Point codes written to port 80h at the start of each routine, the beep codes issued for terminal errors, and a description...
Page 75 2 Troubleshooting Procedures Code Beeps POST Routine Description Initialize keyboard controller 16h 1-2-2-3 BIOS ROM checksum Initialize cache before memory autosize 8254 timer initialization 8237 DMA controller initialization Reset Programmable Interrupt Controller 20h 1-3-1-1 Test DRAM refresh 22h 1-3-1-3 Test 8742 Keyboard Controller Set ES segment register to 4 GB Enable A20 line Autosize DRAM...
Page 76 2 Troubleshooting Procedures Configure advanced cache registers Initialize Multi Processor APIC Enable external and CPU caches Setup System Management Mode (SMM) area Display external L2 cache size Load custom defaults (optional) Display shadow-area message Display possible high address for UMB recovery Display error messages Check for configuration errors Check for keyboard errors...
Page 77 2 Troubleshooting Procedures Code Beeps POST Routine Description Scan for F2 key stroke Enter SETUP Clear Boot flag Check for errors POST done - prepare to boot operating system B4h 1 One short beep before boot Terminate QuietBoot (optional) Check password (optional) Prepare Boot Initialize DMI parameters Initialize PnP Option ROMs...
Page 78 2 Troubleshooting Procedures Code Beeps For Boot Block in Flash ROM Initialize the chipset Initialize the bridge Initialize the CPU Initialize system timer Initialize system I/O Check force recovery boot Checksum BIOS ROM Go to BIOS Set Huge Segment Initialize Multi Processor Initialize OEM special code Initialize PIC and DMA Initialize Memory type...
Page 79: Procedure 3 Diagnostic Test Program Execution Check
2 Troubleshooting Procedures Procedure 3 Diagnostic Test Program Execution Check Execute the following tests from the Diagnostic Test Menu. These tests check the system Tests and Diagnostic, board. Refer to Chapter 3, for more information on how to perform these tests. 1.
Page 80: Usb Fdd Troubleshooting
2 Troubleshooting Procedures 2.5 USB FDD Troubleshooting To check if the USB FDD is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: FDD Head Cleaning Check Procedure 2: Diagnostic Test Program Execution Check Procedure 3: Connector Check and Replacement Check Procedure 1 FDD Head Cleaning Check FDD head cleaning is one option available in the Diagnostic Program.
Page 81 2 Troubleshooting Procedures Procedure 2 Diagnostic Test Program Execution Check Insert the Diagnostics Disk in the USB FDD, turn on the computer and run the test. Refer to Tests and Diagnostics, Chapter 3, for more information about the diagnostics test procedures. Make sure the floppy disk is formatted correctly and that the write protect tab is disabled.
Page 82: Procedure 3 Connector Check And Replacement Check
2 Troubleshooting Procedures Procedure 3 Connector Check and Replacement Check USB FDD is connected to USB port on system board and US board. US board is also connected to system board by cable. The connection of cable and board may be defective. Otherwise, they may be faulty.
Page 83 2 Troubleshooting Procedures Check 2 USB FDD may be faulty. Replace it with a new one. If the problem still occurs, perform Check 3. Check 3 Connect USB FDD to each port embedded on system board. If it does not work properly when connected to CN12, CN19, CN20 or all ports, perform Check 4.
Page 84: Hdd Troubleshooting
User’s Manual. Procedure 1 Partition Check Insert the Toshiba MS-DOS system disk and start the computer. Perform the following checks: Input C: and press Enter. If you cannot change to drive C, go to Check 2. If you Check 1 can change to drive C, go to Procedure 2.
Page 85: Procedure 2 Message Check
2 Troubleshooting Procedures Procedure 2 Message Check When the power is turned on, the system performs the Initial Reliability Test (IRT) installed in the BIOS ROM. When the test detects an error, an error message is displayed on the screen. Make sure no floppy disk is in the FDD.
Page 86: Format Check
2 Troubleshooting Procedures Procedure 3 Format Check The computer’s HDD is formatted using the MS-DOS FORMAT program or the physical format program of the test program. To format the HDD, start with Check 1 below and perform the other steps as required. Refer to the MS-DOS Manual for the operation of MS-DOS.
Page 87: Diagnostic Test Program Execution Check
2 Troubleshooting Procedures Procedure 4 Diagnostic Test Program Execution Check The HDD test program is stored in the Diagnostics Disk. Perform all of the HDD tests in the Tests and Diagnostics, Hard Disk Drive Test. Refer to Chapter 3, for more information about the HDD test program.
Page 88: Procedure 5 Connector Check And Replacement Check
2 Troubleshooting Procedures Procedure 5 Connector Check and Replacement Check HDD(s) is/are connected to the connector(s) on the system board. The connection of HDD(s) and board may be defective. Otherwise, they may be faulty. Disassemble the computer Replacement Procedures following instructions in Chapter 4, and perform the following checks.
Page 89: Keyboard Troubleshooting
2 Troubleshooting Procedures 2.7 Keyboard Troubleshooting To check if the computer’s keyboard is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Diagnostic Test Program Execution Check Procedure 2: Connector and Replacement Check Procedure 1 Diagnostic Test Program Execution Check Execute the Keyboard Test (DIAGNOSTIC TEST) and Pressed key display test (ONLY Tests and Diagnostics ONE TEST) in the Diagnostic Program.
Page 90: Procedure 2 Connector Check And Replacement Check
2 Troubleshooting Procedures Procedure 2 Connector and Replacement Check The connection of cable and board may be defective. Otherwise, they may be faulty. Replacement Disassemble the computer following the steps described in Chapter 4, Procedures , and perform the following checks: Check 1 Make sure keyboard cable is firmly connected to system board.
Page 91: Touch Pad Troubleshooting
2 Troubleshooting Procedures 2.8 Touch pad Troubleshooting To check if the computer’s touch pad is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Diagnostic Test Program Execution Check Procedure 2: Connector and Replacement Check Procedure 1 Diagnostic Test Program Execution Check Execute the Touch pad test (ONLY ONE TEST) in the Diagnostic Program.
Page 92: Procedure 2 Connector Check And Replacement Check
2 Troubleshooting Procedures Procedure 2 Connector and Replacement Check The connection of cable and board may be defective. Otherwise, they may be faulty. Replacement Disassemble the computer following the steps described in Chapter 4, Procedures , and perform the following checks: Check 1 Make sure the cable is firmly connected to system board.
Page 93: Display Troubleshooting
Troubleshooting Procedures 2.9 Display Troubleshooting To check if the computer’s display is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: External Monitor Check Procedure 2: Diagnostic Test Program Execution Check Procedure 3: Connector and Cable Check Procedure 4: Replacement Check Procedure 1 External Monitor Check...
Page 94: Procedure 3 Connector And Cable Check
Troubleshooting Procedures Procedure 3 Connector and Cable Check LCD Module is connected to system board by an LCD/FL cable. FL inverter board is also connected to system board by an LCD/FL cable. And, fluorescent lamp is connected to FL inverter board by HV cable. Their cables may be disconnected from system board or FL inverter board.
Page 95: Procedure 4 Replacement Check
Troubleshooting Procedures Procedure 4 Replacement Check Fluorescent lamp, FL inverter, LCD module, HV cable and LCD/FL cable are connected to Replacement display circuits. Any of these components may be faulty. Refer to Chapter 4, Procedures, for instructions on how to disassemble the computer and then perform the following checks: If fluorescent lamp does not light, perform Check 1.
Page 96: Optical Disk Drive Troubleshooting
Troubleshooting Procedures 2.10 Optical Disk Drive Troubleshooting To check if optical disk drive is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Diagnostic Test Program Execution Check Procedure 2: Connector Check and Replacement Check Procedure 1 Diagnostic Test Program Execution Check Tests Execute the CD-ROM/DVD-ROM Test in the Diagnostic Program.
Page 97: Modem Troubleshooting
Troubleshooting Procedures 2.11 Modem Troubleshooting To check if modem is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Diagnostic Test Program Execution Check Procedure 2: Connector Check and Replacement Check Procedure 1 Diagnostic Test Program Execution Check Execute Modem test in the LAN/Modem/Bluetooth/IEEE1394 test program.
Page 98 Troubleshooting Procedures Check 2 Modem cable may be faulty. Replace it with a new one. If the problem still occurs, perform Check 3. Check 3 MDC may be faulty. Replace it with a new one following the steps in Chapter 4. If the problem still occurs, perform Check 4.
Page 99: Lan Troubleshooting
Troubleshooting Procedures 2.12 LAN Troubleshooting To check if the computer’s LAN is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Diagnostic Test Program Execution Check Procedure 2: Connector Check and Replacement Check Procedure 1 Diagnostic Test Program Execution Check Tests and Diagnostics Execute LAN test in the LAN/Modem test program.
Page 100: Wireless Lan Troubleshooting
Troubleshooting Procedures 2.13 Wireless LAN Troubleshooting To check if the computer's Wireless LAN is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Transmitting-Receiving Check Procedure 2: Antennas' Connection Check Procedure 3: Replacement Check Procedure 1 Transmitting-Receiving Check Before starting the test, make sure the wireless communication switch is set in the ON position.
Page 101: Procedure 2 Antennas' Connection Check
Troubleshooting Procedures Procedure 2 Antennas' Connection Check The wireless LAN function-wiring diagram is shown below: Any of the connections may be defective. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures , and perform the following checks: Check 1 Make sure the wireless communication switch is “On”.
Page 102: Procedure 3 Replacement Check
Troubleshooting Procedures Procedure 3 Replacement Check Wireless LAN card, wireless LAN antenna or system board may be faulty. Refer to Chapter 4, Replacement Procedures, for instructions on how to disassemble the computer and then perform the following checks: Check 1 Wireless LAN antenna may be faulty.
Page 103: Sound Troubleshooting
Troubleshooting Procedures 2.14 Sound Troubleshooting To check if the sound function is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Connector Check Procedure 2: Replacement Check Procedure 1 Connector Check The connection of sound system is shown in the following figure. As the connection may be defective, disassemble the PC and check each connection.
Page 104 Troubleshooting Procedures Procedure 2 Replacement Check If External microphone/Headphone does not work properly, perform check 1. If Internal microphone /Speaker does not work properly, perform check 2. If HP out &SPDIF does not work properly, perform check 3. If Line in/ Volume control does not work properly, perform check 4. Check 1 External microphone/Headphone may be faulty.
Page 105: Vga Troubleshooting
Troubleshooting Procedures 2.15 VGA Troubleshooting Procedure 1 Diagnostic Test Program Execution Check Tests and Diagnostics Execute VGA test in the test program. Refer to Chapter 3, for more information on how to perform the test program. If any error is detected, perform Procedure 2. Procedure 2 Connector Check and Replacement Check VDC (VGA Daughter Card) is used as the VGA for this computer.
Page 106 Troubleshooting Procedures Check 5 System board may be faulty. Replace it with a new one following the instruction in Chapter 4. Satellite P100 Maintenance Manual...
Page 107: Procedure 1 Diagnostic Test Program Execution Check
Troubleshooting Procedures 2.16 Fingerprint Troubleshooting To check if the computer’s Fingerprint is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Connector Check and Replacement Check Procedure 1 Diagnostic Test Program Execution Check Tests and Diagnostics Execute Fingerprint test in the test program. Refer to Chapter 3, more information on how to perform the test program.
Page 108: Procedure 1
Troubleshooting Procedures 2.17 Bluetooth Troubleshooting To check if the computer’s Bluetooth is malfunctioning or not, follow the troubleshooting procedure below as instructed. Procedure 1: Connector Check and Replacement Check Procedure 1 Connector Check and Replacement Check The Bluetooth function is connected to system board. If Bluetooth malfunctions, its connection is defective or Bluetooth cable and system board may be faulty.
Page 109: Chapter 3 Test Program For Field
Test Program for Field. Chapter 3 Diagnostic Programs Satellite P100 and Satellite Pro P100 Tests and Diagnostics Manual...
Page 110 Test Program for Field. Chapter 3 Contents Tests and Diagnostics Software Overview ............3-3 Executing the Diagnostic Test ................3-4 Subtest names......................3-8 System Test......................3-11 Memory Test......................3-13 Keyboard Test...................... 3-16 Display Test ......................3-19 Floppy Disk Test....................3-34 Hard Disk Test .....................
Page 111: Tests And Diagnostics Software Overview
The Diagnostics Disk (all tests) A formatted working disk for the floppy disk drive test (all tests) A CD test media (Toshiba Backup CD ROM for the CD-ROM test) The following sections detail the tests contained within the Diagnostic Test Menu. Refer to Sections 3.18, 3.19, 3.20 and, 3.21 for detailed information on the remaining functions of the...
Page 112: Executing The Diagnostic Test
1. Create a DOS bootable disk and copy all the files from the Tests and Diagnostics software to the disk. 2. Insert the boot disk into the computer’s floppy disk drive and turn on the computer. The following screen displays: TOSHIBA Satellite(Pro) P100 Diagnostics ::Select item Version v1.00 (C) Copyright QUANTA Corp. 2005- :Escape [ DIAGNOSTICS MENU ] 01.DIAGNOSTIC TEST...
Page 113 Test Program for Field. The following menu displays: TOSHIBA Satellite(Pro) P100 Diagnostics ::Select item Version V1.00 (C) Copyright QUANTA Corp. 2005- :Escape [ DIAGNOSTICS MENU ] 01. DIAGNOSTIC TEST 02. RUNNING TEST 03. DMI INFORMATION [ DIAGNOSTIC TEST MENU ] 04.
Page 114 Diagnostic Test and returns to the Diagnostics Menu. 4. Select the subtest you want to execute and press Enter. The following menu displays: TOSHIBA Satellite(Pro) P100 Diagnostics : :Select item Version V1.00 (C) Copyright QUANTA Corp. 2005-...
Page 115 Test Program for Field. TOSHIBA Satellite(Pro) P100 Diagnostics : :Select item Version V1.00 (C) Copyright QUANTA Corp. 2005- :Escape [ DIAGNOSTICS MENU ] [ SYSTEM TEST ] [ TEST PARAMETER ] 01. DIAGNOSTIC TEST 01. FAN ON/OFF 01. FAN ON/OFF 01.
Page 116: Subtest Names
Test Program for Field. Subtest names Table 3-1 lists the subtest names for each test program in the Diagnostic Test menu. Table 3-1 Subtest Names(1/3) Test Name Subtest Name SYSTEM TEST FAN ON/OFF check Battery TEST CPU Temperature CIR Remote Control Test FINGERPRINT TEST MEMORY TEST Conventional Memory...
Page 117 Test Program for Field. Table 3-1 Subtest Names(2/3) Test Name Subtest Name FLOPPY DISK TEST Sequential Read Sequential W/R/C Random Address/Data Write Specified Address Read Specified Address HARD DISK TEST Sequential Read Address Uniqueness Random Address Data Cross Talk and Peek Shift Write Specified Address Read Specified Address Sequential Write...
Page 118 Test Program for Field. Table 3-1 Subtest Names(3/3) Test Name Subtest Name MULTIMEDIA TEST Sequential Read Test Random Read Test Read Specified Address Test 1 point W/R/C Test MEMORY2 All one/zero Test Walking 1/Walking 0 Test(Left) Walking 1/Walking 0 Test(Right) Walking 1/Walking 0 Test(Left /Right) *This test cannot support.
Page 119: System Test
Test Program for Field. System Test To execute the System Test select 01 from the Diagnostic Test Menu, press Enter and follow the directions on the screen. The System Test contains two subtests. Move the highlight bar to the subtest you want to execute and press Enter. Subtest 01 FAN ON/OFF Checking Select 1,2,3 to control FAN on/off , 1=Fan on , 2=Fan off , 3=Exit .
Page 120 Test Program for Field. Subtest 03 CPU Temperature This will display CPU Temperature for check , press [ESC] to exit . [CPU_TEMP.EXE] Program Version : 1.0 08-08-2005 CPU Temperature : XX Subtest 04 CIR Remote Control Test When you execute this subtest, the remote control layout is drawn on the display.
Page 121: Memory Test
Test Program for Field. Memory Test To execute the Memory Test select 02 from the Diagnostic Test Menu, press Enter and follow the directions on the screen. The Memory Test contains five subtests that test the computer’s memory. Move the highlight bar to the subtest you want to execute and press Enter.
Page 122 Test Program for Field. 5. Address pattern test “16 bit write and 16 bit read” of address pattern data is executed and the new data is compared with the original data. Test data = 0000H, 0004H, 0008H, 000CH,...8000H, 8004H, through FFECH Subtest 02 Protected Mode...
Page 123 Test Program for Field. Test Process: 1. Checks the memory size to determine the maximum size of installed memory. 2. Tests memory addresses 0 to the maximum installed. 3. Writes, reads, and compares test data after a memory refresh cycle (16ms or more).
Page 124: Keyboard Test
Test Program for Field. Keyboard Test To execute the Keyboard Test select 03 from the Diagnostic Test Menu, press Enter and follow the directions on the screen. The Keyboard Test contains seven subtests that test the computer’s keyboard and mouse actions. Move the highlight bar to the subtest you want to execute and press Enter.
Page 125 Test Program for Field. Subtest 03 Hot Key Display [6 Key] This subtest is used for the 6 hot key and functions the same as Subtest 1. Subtest 04 Hot Key Display [7 Key] This subtest is used for the 7 hot key and functions the same as Subtest 1. Subtest 05 Keyboard LED The LED display for Num Lock, Caps Lock, and Scroll Lock (in that order)
Page 126 Test Program for Field. LEFT PRESS TOUCH_PAD TEST RIGHT PRESS Please Do Not Press the Left and Right Button At The Same Time Satellite P100 and Satellite Pro P100 Tests and Diagnostics Manual...
Page 127: Display Test
Test Program for Field. Display Test To execute the Display Test select 04 from the Diagnostic Test Menu, press Enter and follow the directions displayed on the screen. The Display Test contains twelve subtests that test the display in various modes. Move the highlight bar to the subtest you want to execute and press Enter.
Page 128 Test Program for Field. Press Enter if NO was selected for Test Loop on the Test Parameter Menu. Press Ctrl + break if YES was selected for Test Loop on the Test Parameter Menu. Subtest 02 Character Set This subtest displays the character codes 00H - FFH, using Mode 01H (40*25).
Page 129 Test Program for Field. Subtest 03 80 * 25 Character Display This subtest uses 80*25 video resolution to display character codes 20H - 7EH using Mode 03H (80*25). The data displayed is shifted 1 byte to the left for each line as shown below. 80*25 CHARACTER DISPLAY 01234567890123456789012345678901234567890123456789012345678901234567890123456789 !”#$%&’()*=,.-/0123456789:;...
Page 130 Test Program for Field. Subtest 04 320 * 200 Character Display This subtest uses 320*200 video resolution to display green, red and yellow followed by cyan, magenta, and white. The screen below shows the displays when this subtest is executed. 320 * 200 GRAPHICS DISPLAY COLOR SET 0 : [ 4 ] GREEN...
Page 131 Test Program for Field. 320*200 GRAPHICS DISPLAY [ D ] BLACK GRAY BLUE BLUE GREEN GREEN CYAN CYAN MAGENTA MAGENTA BROWN YELLOW WHITE WHITE Press [Enter] KEY Press ENTER to display 64 gradations of red, green, blue and white on the screen 320*200 GRAPHICS DISPLAY [ 13 ]...
Page 132 Test Program for Field. Subtest 05 640 * 200 Character Display This subtest uses 640*200 video resolution to display three windows, each window drives a different set of dots: even dots, odd dots and all dots. The screen below displays when this subtest is executed. 640 * 200 GRAPHICS DISPLAY : [ 6 ] EVEN...
Page 133 Test Program for Field. Subtest 06 640 * 480 Character Display This subtest uses 640*350 video resolution to display 16 colors: black, blue, green, cyan, red, magenta, brown, white, dark gray, light blue, light green, light cyan, light red, light magenta, yellow, and intensified white. The screen below displays when this subtest is executed.
Page 134 Test Program for Field. 640*480 GRAPHICS DISPLAY [12 ] BLACK DARK GRAY BLUE LIGHT BLUE GREEN LIGHT GREEN CYAN LIGHT CYAN LIGHT MAGENTA LIGHT MAGENTA BROWN YELLOW WHITE INTENSIFIED WHITE Press [Enter] KEY To exit this subtest and return to the Display Test menu: Test Loop Press Enter if NO was selected for on the Test Parameter Menu.
Page 135 Test Program for Field. Subtest 07 Display Page This subtest displays video pages zero through seven. DISPLAY PAGE 0 000000000000000000000000000000000000000000000000000000000000000 ............0 0............0 0............0 0............0 0............0 0............0 0............0 0............0 0............0 0............0 0............0 0............0 0............0 0............0 0............0 0............0 0............0 0............00 ............0 000000000000000000000000000000000000000000000000000000000000000 To exit this subtest and return to the Display Test menu: Test Loop Press Enter if NO was selected for...
Page 136 Test Program for Field. Subtest 08 "H" Pattern Display This subtest displays a full screen of "H" patterns. HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH To exit this subtest and return to the Display Test menu:...
Page 137 Test Program for Field. Subtest 10 Color Graphics Display This subtest displays three colors, cyan, white and yellow on the screen as shown below. 640 * 480 GRAPHICS DISPLAY CYAN WHITE YELLOW To exit this subtest and return to the Display Test menu: Test Loop Press Enter if NO was selected for on the Test Parameter Menu.
Page 138 Test Program for Field. Subtest 11 Color Attributes Display This subtest displays 16 colors: black, blue, green, cyan, red, magenta, brown, white, dark gray, light blue, light green, light cyan, light red, light magenta, yellow, and intensified white. The screen below displays when this subtest is executed.
Page 139 Test Program for Field. NOTE: The following screen does not display correctly. It will be amended in the next version. Press [Enter] Key Press Enter to execute the VRAM mapping test which displays a vertical line at four dot intervals using Mode 12. Press [Enter] Key Press Enter to display VRAM mapping test using the all dots Mode.
Page 140 Test Program for Field. Press [Enter] Key To exit this subtest and return to the Display Test menu: Test Loop Press Enter if NO was selected for on the Test Parameter Menu. Test Loop Press Ctrl + break if YES was selected for on the Test Parameter Menu.
Page 141 Test Program for Field. Subtest 12 Color Tiling This subtest displays black, gray, white, and 3 gradations of red, green, and blue as shown in the following display. Black Green Blue Gray Green Blue Gradation Gradation Gradation White Green Blue Gradation Gradation Gradation...
Page 142: Floppy Disk Test
Test Program for Field. Floppy Disk Test CAUTION: Before running the floppy disk test, prepare a formatted work disk. Remove the diagnostics disk and insert the work disk into the FDD. The contents of the floppy disk will be erased. To execute the Floppy Disk Test select 05 from the Diagnostic Test Menu, press Enter and follow the directions on the screen.
Page 143 Test Program for Field. Subtest 04 Write Specified Address NOTE: The first two digits of the ADDRESS indicate which track is being tested, the next two digits indicates the head, and the last two digits indicate the sector. This subtest allows you to verify the errors from Subtest 02. It writes specified data to a specified track and head.
Page 144: Hard Disk Test
Test Program for Field. Hard Disk Test To execute the Hard Disk Test select 06 from the Diagnostic Test Menu, press Enter and follow the directions on the screen. The Hard Disk Test contains eight subtests that test the functions of the hard disk drive. Move the highlight bar to the subtest you want to execute and press Enter.
Page 145 Test Program for Field. Subtest 04 Cross Talk and Peak Shift This subtest writes eight of the most likely to fail data patterns (shown below) to a cylinder on the HDD, then reads the data while moving from cylinder to cylinder.
Page 146 Test Program for Field. Subtest 07 Sequential Write This subtest writes specified data to all cylinders on the HDD. The following message displays on the screen to enter the test data. TEST DATA ????(=37b3H) Subtest 08 W-R-C Specified Address This subtest writes specified data to a specified sector count, then reads and compares the result.
Page 147: Real Time Clock Test
Test Program for Field. 3.10 Real Time Clock Test To execute the Real Time Clock Test select 07 from the Diagnostic Test Menu, press Enter and follow the directions on the screen. The Real Time Clock Test contains three subtests that test the computer’s real time functions.
Page 148 Test Program for Field. Subtest 02 Backup Memory This subtest writes 50 bytes of test data (FFH, AAH, 55H, and 00H) to the CMOS 14 address, then reads the new data and compares it to the original data. Subtest 03 Real Time Carry CAUTION: When this subtest is executed, the current date and time are reset.
Page 149: Cache Memory Test
Test Program for Field. 3.11 Cache Memory Test To execute the Cache Memory Test select 08 from the Diagnostic Test Menu, press Enter and follow the directions on the screen. The Cache Memory Test contains eight subtests that test the computer's cache memory. Move the highlight bar to the subtest you want to execute and press Enter.
Page 150 Test Program for Field. Subtest 04 Bit Shift Pattern Test This subtest reads the contents of cache memory and saves it into RAM. The subtest then writes the bit shift data patterns (1 bit shifted every 4 bytes reads the new data and compares the result with the original data. The original cache memory content is then restored to the cache memory.
Page 151: High Resolution Display Test
Test Program for Field. 3.12 High Resolution Display Test To execute the High Resolution Display Test select 09 from the Diagnostic Test Menu, press Enter and follow the directions on the screen. The High Resolution Display Test contains six subtests that test the computer's high resolution video display. Move the highlight bar to the subtest you want to execute and press Enter.
Page 152 Test Program for Field. Subtest 02 640*480 Mode Display This subtest uses 640*480 video resolution to display a high resolution white frame, 256 letter types (8*16 pixels) and 64 gradations of white, red, green, and blue as shown below. [ 640*480 256 ] Press [ Enter ]key 256 letter types...
Page 153 Test Program for Field. Subtest 03 800 * 600 Mode Display This subtest uses 800*600 video resolution to display a high resolution white frame, 256 letter types (8*16 pixels) and 256 gradations of white, red, green, and blue as shown below. Press [ Enter ] key 800*600 256 256 letter types...
Page 154 Test Program for Field. Subtest 04 1024* 768 Mode Display This subtest uses 1024*768 video resolution to display a high resolution white frame, 256 letter types (8*16 pixels) and 64 gradations of white, red, green, and blue as shown below. [ 1024*768 256 ] Press [ Enter ] key 256 letter types...
Page 155 Test Program for Field. Subtest 05 “H” Pattern Display This subtest uses the 1024*768 Mode to display a high resolution white frame, “H” letters (8*16 pixels fonts), at 128 letters by 48 lines. HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH...
Page 156 Test Program for Field. Subtest 06 Focus Test ( “E” Pattern) This subtest sets the 1024*768 Mode and displays “E” patterns (18*18 dot fonts), at 56 letters *42 lines surrounded by a high resolution white frame. To exit this subtest and return to the High Resolution Display Test menu: Test Loop Press Enter if NO was selected for on the Test Parameter Menu.
Page 157: Multimedia Test
The Multimedia Test contains four subtests that test the computer's multimedia functions. Move the highlight bar to the subtest you want to execute and press Enter. NOTE: Use the Toshiba Backup CD-ROM for Subtests 01, 02, and 03. Subtest 01 Sequential Read Test This subtest sequentially reads one block unit (2K bytes) of all logical addresses from the test CD.
Page 158: Memory2 Test
Test Program for Field. 3.14 MEMORY2 Test To execute the Expansion Test select 11 from the Diagnostic Test Menu, press Enter and follow the directions on the screen. The MEMORY2 Test contains four subtests that test the computer's. Move the highlight bar to the subtest you want to execute and press Enter. NOTE: If NO is selected for Test Loop on the Test Parameter menu, the Test Status screen displays while the test is executing.
Page 159 Test Program for Field. Tee test method is the same as Subtest2. However, the data to be used differs. 7FFF7FFF7FFF7FFF8000800080008000 BFFFBFFFBFFFBFFF4000400040004000 DFFFDFFFDFFFDFFF2000200020002000 FFFBFFFBFFFBFFFB0004000400040004 FFFDFFFDFFFDFFFD0002000200020002 FFFEFFFEFFFEFFFE0001000100010001 80008000800080007FFF7FFF7FFF7FFF 4000400040004000BFFFBFFFBFFFBFFF 0004000400040004FFFBFFFBFFFBFFFB 0002000200020002FFFDFFFDFFFDFFFD 0001000100010001FFFEFFFEFFFEFFFE Satellite P100 and Satellite Pro P100 Tests and Diagnostics Manual...
Page 160: Error Codes And Error Status Names
Test Program for Field. 3.15 Error Codes and Error Status Names The following table lists the error codes and error status names for the Diagnostic Tests. Table 3-2 Error codes and error status names (1/2) Device Name Error Code Error Status Name (Common) Data Compare Error Memory...
Page 161 Test Program for Field. Table 3-2 Error codes and error status names (2/2) Device Name Error Code Error Status Name Undefined Error Write Fault Status Error No Sense Error Other Error Cache Memory Protect Mode Error Caching Error Other Error Multimedia Write Error Invalid Drive...
Page 162: Running Test
Test Program for Field. 3.16 Running Test NOTES: 1. You may add or delete subtests using the Running Test Edit Item function, see Section 3.20. 2. Do not forget to insert a work disk in the FDD. If a work disk is not inserted an error will be generated during the Floppy Disk Test.
Page 163: Dmi Infoemation
2. Region Code 3.17.2 Write DMI Information The Write DMI Information program contains the following information for the computer : 1. Manufacture Name ( TOSHIBA ) 2. Product Name ( Satellite XXXXXX ) 3. Part Number ( PSL20X-XXXXXX ) 4. Serial Number ( 12345678W ) 5.
Page 164 , if over will retry keyin Note : Please Check New DMI Information After System Restart !! 1. **** Manufacture Name ( TOSHIBA ) - (15) 2. **** Product Name ( Satellite XXXXXX ) - (31) 3.
Page 165: Log Utilities
Test Program for Field. 3.18 Log Utilities This function logs error information generated while a test is in progress and stores the results in RAM (Maximum error log : 500 times). This function can store data on a floppy disk. If the power switch is turned off, the error information will be lost. Error information is displayed in the following order: 1.
Page 166 Test Program for Field. 2. Error information displayed on the screen can be manipulated with the following number keys: The 1 key scrolls the display to the next page. The 2 key scrolls the display to the previous page. The 3 key returns to the Diagnostics Menu. The 4 key erases all error log information in RAM.
Page 167: System Configuration
Test Program for Field. 3.19 System Configuration Select 05 from the Diagnostics Menu and press Enter to display the following system configuration: SYSTEM CONFIGURATION : * - BIOS VER = VX.XX KBC VER = XXXX * - MAC ADDRESS : XXXXXXXXXXXX * - 0 ASYNC ADAPTER * - 1 HDD DRIVE(S):XXXXXXXXXXXXXXXXXXXXXXXXXX FW Rev.:XXXXXXXX...
Page 168: Running Test Edit Item
Test Program for Field. 3.20 Running Test Edit Item 3.20.1 Function Description Function description lets you add or delete the subtests used to execute the Running Test. The following screen displays after pressing the Tab key to edit an item in the Running Test. KEY OPERATION Cursor Down Cursor Up...
Page 169 Test Program for Field. 1. Enter a number or 0 for Loop Count and press Enter. Select a number from 1 to 65535 to define the number of times the Running Test executes. Select 0 to run the test continuously until halted by the user. 2.
Page 170: Common Tests And Operation
Test Program for Field. 3.21 Common Tests and Operation 3.21.1 How to operate a window To input parameters, or open a window use the following keys. : to move a highlight bar [Enter] key : to select an item at the highlight bar [Esc] key : to close the current window and go back to the previous window...
Page 171 Test Program for Field. Pass Count Displays the number of times the test has been executed. Error Count Displays the number of errors which have occurred during the test. Write Data Displays only the test data that has failed to compare during the test while being written during the test.
Page 172: Test Stop Display
Test Program for Field. 3.21.4 Test Stop Display If an error occurs during a Subtest and YES is selected for Error Stop, the following message displays: [HALT OPERATION] 1. Test end 2. Continue 3. Retry * Select 1, 2, or 3 The three selections have the following functions: 1: Terminates the test program and exits to the subtest menu.
Page 173: Chapter 4 Replacement Procedures
Chapter 4 Replacement Procedures Satellite P100 Maintenance Manual (960-Q02)
Page 174 Replacement Procedures 4-ii Satellite P100 Maintenance Manual (960-Q02)
Page 175 Replacement Procedures Chapter 4 Contents Overview........................4-1 Safety Precautions ....................4-2 Before You Begin ....................4-3 Disassembly Procedure..................4-4 Assembly Procedure .................... 4-5 Tools and Equipment ................... 4-5 Screw Tightening Torque ..................4-6 Grip Color ......................4-6 Screw Notation..................... 4-7 Battery pack .......................
Page 176 Replacement Procedures Figures Figure 4-1 Removing the battery pack................. 4-8 Figure 4-2-1 Removing a PC card ..................4-10 Figure 4-3-2 Insert a PC card..................... 4-11 Figure 4-4 Removing the HDD assembly................4-13 Figure 4-4 Removing a HDD..................... 4-14 Figure 4-5 Removing a wireless LAN card ............... 4-16 Figure 4-6 Removing a memory module ................
Page 177 Replacement Procedures Figure 4-31 Removing the display mask ................4-52 Figure 4-32 Removing the FL inverter ................4-53 Figure 4-33 Removing the LCD unit ................... 4-54 Figure 4-34 Removing the LCD supports................4-55 Satellite P100 Maintenance Manual (960-Q02)
Page 178: Overview
Replacement Procedures Overview This chapter describes the procedure for removing and replacing the field replaceable units (FRUs) in the PC. It may not be necessary to remove all the FRUs in order to replace one. The chart below provides a guide as to which other FRUs must be removed before a particular FRU can be removed.
Page 179: Safety Precautions
DANGER: 1. In the case of the battery, always use authentic parts or equivalent parts approved by Toshiba. Other batteries may have different specifications that are incompatible with the computer and may result in fire or explosion.
Page 180: Before You Begin
Replacement Procedures Before You Begin Take note of the following points before starting work. Always remove the AC adapter and battery pack before commencing any of the procedures. The procedure for removing the battery pack is described in section “4.2.1 Battery Pack”. 1.
Page 181: Disassembly Procedure
Replacement Procedures Disassembly Procedure Three main types of cable connector are used. • Pressure plate connector • Spring connector • Normal pin connector When disconnecting a pressure plate connector, lift up the tag on one side of the plastic pressure plate on the connector and pull the cable out from the connector. When reconnecting a cable to a pressure plate connector, lift up the pressure plate to a suitable height and insert the cable into the connector.
Page 182: Assembly Procedure
Replacement Procedures Assembly Procedure After the computer has been disassembled and the part that caused the fault has been repaired or replaced, the computer must be reassembled. Take note of the following general points when assembling the computer. • Take your time and follow the instructions carefully. Hurrying the assembly work will only introduce new problems.
Page 183: Screw Tightening Torque
Replacement Procedures Screw Tightening Torque Use the following torque when tightening screws. CAUTION: Overtightening may damage screws or parts. Undertightening may allow screws to loosen (and possibly fall out) causing a short circuit or other damage. NOTE: To tighten screws quickly and accurately, an electric screwdriver is recommended.
Page 184: Screw Notation
Replacement Procedures Screw Notation To make maintenance of the computer easier, markings of the kinds of the screws including the types and lengths of the screws are indicated on the computer body. Format: Screw shape + Screw length (mm) Screw shape B: Bind screw F: Thin head screw S: Super thin head screw...
Page 185: Battery Pack
Replacement Procedures Battery pack Removing the battery pack The following describes the procedure for removing the battery pack (See Figure 4-1). CAUTION: Take care not to short circuit the terminals when removing the battery pack. Similarly, do not drop, knock, scratch, disassemble, twist, or bend the battery pack.
Page 186 Dispose always the used battery pack in accordance with the laws and ordinances of your local authority. Use only the batteries approved by Toshiba. NOTE: Check visually the battery terminals and clean off any dirt with a dry cloth.
Page 187: Pc Card
Replacement Procedures 4.3 PC card Removing a PC card The following describes the procedure for removing a PC card (See Figure 4-2-1). CAUTION: Insert or remove a PC card in accordance with any instructions in a PC card manual or the manuals of the computer system you are using. 1.
Page 188 Replacement Procedures Installing a PC card The following describes the procedure for inserting a PC card (See Figure 4-2-2). 1. Make sure the eject button does not stick out. 2. Insert a PC card and press it until it is securely connected. Figure 4-2-2 Insert a PC card Satellite P100 Maintenance Manual (960-Q02) 4-11...
Page 189: Hdd
Replacement Procedures Removing a HDD The following describes the procedure for removing a HDD (See Figure 4-3 to 4-4). CAUTION: Take care not to press on the top or bottom of a HDD. Pressure may cause data loss or damage to the device. 1.
Page 190 Replacement Procedures CAUTION: When a HDD is installed, they are installed in the position as the following figure. HDD Door M2.5x4.0B FLAT BIND M3.0x3.5B FLAT BIND module CN 19 Figure 4-3 Removing the HDD assembly Satellite P100 Maintenance Manual (960-Q02) 4-13...
Page 191 Replacement Procedures 5. Remove the following screws securing the HDD holder and remove the HDD holder. • M3.0×3.5B FLAT BIND screw HDD holder M3.0x3.5 FLAT BIND Figure 4-4 Removing a HDD 4-14 Satellite P100 Maintenance Manual (960-Q02)
Page 192 Replacement Procedures Installing a HDD The following describes the procedure for installing a HDD (See Figure 4-3 to 4-4). 1. Install a HDD to the HDD holder and secure it with the following screws. • M3.0×3.5F FLAT BIND screw NOTE: Although they are 3mm head screws, screw torque must be set in 2.5kg-cm for four screws securing the HDD holder.
Page 193: Wireless Lan Card
Replacement Procedures Wireless LAN card Removing a Wireless LAN card The following describes the procedure for removing a Wireless LAN card (See Figure 4-5). 1. Remove the following screw of wireless cover securing wireless LAN card cover and remove it. And remove screw of wireless board •...
Page 194 Replacement Procedures Installing a Wireless LAN card The following describes the procedure for installing a Wireless LAN card (See Figure 4-5). 1. Insert a wireless LAN card terminals slantwise into the connector CN30 on the computer and press a wireless LAN card and lock the secure screws. 2.
Page 195: Memory Module
Replacement Procedures Memory module CAUTION: The power of the computer must be turned off when you remove a memory module. Removing a memory module with the power on risks damaging the module or the computer itself. Do not touch memory module terminals. Any dirt on the terminals may cause memory access problems.
Page 196 Replacement Procedures Memory Module Cover Figure 4-6 Removing a memory module Satellite P100 Maintenance Manual (960-Q02) 4-19...
Page 197 Replacement Procedures Installing a memory module To install a memory module, confirm that the computer is in boot mode. Then perform the following procedure (See Figure 4-7). 1. Insert a memory module into the connector of the computer slantwise (terminal side first) and press it to connect firmly.
Page 198: Keyboard
Replacement Procedures Keyboard Removing the keyboard The following describes the procedure for removing the keyboard (See Figure 4-8 to 4-9). CAUTION: As the keycap may fall out, when handling the keyboard always hold it by the frame and do not touch the keycap. 1.
Page 199 Replacement Procedures KBD cover Figure 4-8 Removing screws for KBD cover/keyboard Screw 2.5x3.0 Keyboard Figure 4-9 Removing the keyboard/KBD cover 4-22 Satellite P100 Maintenance Manual (960-Q02)
Page 200 Replacement Procedures Installing the keyboard The following describes the procedure for installing the keyboard (See Figure 4-8 to 4-9). 1. Turn the keyboard upside down and place it on the palm rest as its face down. Connect the keyboard flexible cable to the connector CN3200 on the system board. 2.
Page 201: Function Button Board
Replacement Procedures Function Button Board Removing the Function Board The following describes the procedure for removing the Function board (See Figure 4-10). 1. Remove the following screw securing the switch membrane. • M2.5×3.0B FLAT BIND screw 2. Unlock the Function board cable and Push up the Function board to the arrow direction and remove it.
Page 202 Replacement Procedures Installing the Function Board The following describes the procedure for installing the switch membrane. 1. Press Function board in the computer. 2. Secure the Function board with the following screw. • M2.5×3.0B FLAT BIND screw Satellite P100 Maintenance Manual (960-Q02) 4-25...
Page 203: Optical Disk Drive
Replacement Procedures Optical disk drive NOTE: Do not apply excessive force to the top of an optical disk drive. Do not touch the shaded portion of the figure below, when the drive is removed or installed. Removing an optical disk drive The following describes the procedure for removing an optical disk drive (See Figure 4- 11and 4-12).
Page 204 Replacement Procedures ODD bracket M2.0×3.0 Figure 4-12 Disassembling the side bracket Installing an optical disk drive The following describes the procedure for installing an optical disk drive (See Figure 4-11 and 4-12). 1. Attach the ODD bracket to an optical disk drive and secure it with the following screws.
Page 205: Display Assembly
Replacement Procedures 4.10 Display assembly Removing the display assembly The following describes the procedure for removing the display assembly (See Figure 4-13 to 4-17). 1. Close the display and turn the computer upside down. 2. Open the MINIPCI Door and remove the wireless LAN screws and antenna connector.
Page 206 Replacement Procedures 3. Open the display and removing the k/b cover and keyboard. Figure 4-14 Removing keyboard cover 4. Disassembly Function board and pull out the wireless LAN antenna and LCD cables from the guide, If there was Bluetooth Antenna, pls. also remove it ( the 5th point) Figure 4-25 Removing the Wireless Antenna and Bluetooth Satellite P100 Maintenance Manual (960-Q02) 4-29...
Page 207 Replacement Procedures 4. Opening the display to 180 degree, and remove the hinge screw . ‧ M2.5×6.0 FLAT BIND screw (Locktight) M2.5x6.0 FLAT BIND (Locktight) M2.5x6.0 FLAT BIND (Locktight) Figure 4-36 Removing the hinge screw 4-30 Satellite P100 Maintenance Manual (960-Q02)
Page 208 Replacement Procedures 5. Remove the LCD harness from the connector on the system board and pulling out the pole of hinge from the hole of hinge assembly, remove the display assembly from the base assembly. Display assembly Base assembly Figure 4-17 Removing the LCD harness and remove display assembly Satellite P100 Maintenance Manual (960-Q02) 4-31...
Page 209 Replacement Procedures Installing the display assembly The following describes the procedure for installing the display assembly (See Figure 4-13 to 4-17). 1. Inserting the pole of hinge to the hole of hinge assembly, set the display assembly on the base assembly. 2.
Page 210 Replacement Procedures 4.11 Bluetooth The following describes for installing the display assembly (See Figure 4-18). Removing the Bluetooth 1. Pull out the Bluetooth cable connect from Bluetooth board 2. Loose the below screw and pull out the MB->BT cable. M2.3x3.0 Bluetooth Antenna M2.0*3.0...
Page 211: Cover Assembly
Replacement Procedures 4.12 Cover assembly Removing the cover assembly The following describes the procedure for removing the cover assembly (See Figure 4-19 to 4-21). 1. Turn over the computer. 2. Remove the following screws securing the cover assembly from the back and bottom of computer.
Page 212 Replacement Procedures Screws 2.5*6 Screws 2.5*4 Screws 2.5*6 Figure 4-40 Removing the screws (back) 3. Disconnect the touch pad flat cable/Fingerprint cable/Top LENS from the connector on the system board. Satellite P100 Maintenance Manual (960-Q02) 4-35...
Page 213 Replacement Procedures 4. Pull up and remove the cover assembly from the base assembly. Cover assembly Cable drain Base assembly Figure 4-21 Removing the cover assembly 4-36 Satellite P100 Maintenance Manual (960-Q02)
Page 214 Replacement Procedures Installing the cover assembly The following describes the procedure for installing the cover assembly (See Figure 4-19 to 4-21). 1. Install the cover assembly to the base assembly. NOTE: Be careful not to catch the cables between cover assembly and base assembly. 2.
Page 215: Touch Pad
Replacement Procedures 4.13 Touch pad Removing the touch pad The following describes the procedure for removing the touch pad (See Figure 4-22). 1. Peel off the glass tape and disconnect the touch pad flat cable from the connector on the touch pad and peel the al foil. 2.
Page 216 Replacement Procedures Installing the touch pad The following describes the procedure for installing the touch pad (See Figure 4-22). 1. Peel off the separator covering on the sensor portion of a new touch pad. NOTE: Do not reuse the touch pad so that it can not be used after peeling off from the computer.
Page 217: Audio Board
Replacement Procedures 4.14 Audio Board The following describes for removing the cover assembly (See Figure 4-23). Removing the audio board 1. Pull out the audio board cable from audio board connect CN4 2. Loose the below screws and then incline pull out audio board. M2.5x4.0 FLAT BIND screw Figure 4-23 Removing the Audio Board...
Page 218 Replacement Procedures 4.15 Fingerprint The following describes for removing the cover assembly (See Figure 4-24). Remove the Fingerprint 1. Pull out the fingerprint cable from connect CN5 2. Loose below screws from fingerprint board and take it out top case M2.5x4.0 FLAT BIND screw M2.5x4.0...
Page 219: Usb Board
Replacement Procedures 4.16 USB Board The following describes for removing the cover assembly (See Figure 4-25). Removing USB board 1. Remove the USB cable from CN4 and USBCN1 2. Loose below screw from USB board M2.5x4.0 FLAT BIND screw Figure 4-25 Removing the USB board Installing the USB Board 1.
Page 220 Replacement Procedures Satellite P100 Maintenance Manual (960-Q02) 4-43...
Page 221 Replacement Procedures 4-44 Satellite P100 Maintenance Manual (960-Q02)
Page 222: System Board
Replacement Procedures 4.17 System board CAUTION: 1. When handling the system board, always hold by the edges. Do not touch the printed circuit face. 2. If replacing with a new system board, execute the subtest01 Initial configuration in section 3.3 “Setting of the hardware configuration”. Also update with the latest BIOS as described in Appendix G “BIOS Rewrite Procedures”...
Page 223 Replacement Procedures Installing the system board The following describes the procedure for installing the system board (See Figure 4-26). 1. Secure the system board with the following screws. • M2.5×4.0 BIND screw 2. Connect the speaker cable to the connector CN 10 on the system board. 4-46 Satellite P100 Maintenance Manual (960-Q02)
Page 224: Cpu
Replacement Procedures 4.18 CPU Removing the CPU heat sink The following describes the procedure for removing the CPU heat sink (See Figure 4-27 ). 1. Disconnect the Heat sink cable from the connector CN20 on the system board 2. Remove the following screws securing the heat sink holder along 1 to 3. •...
Page 225 Replacement Procedures 4. Unlock the CPU by rotating the cam on the CPU socket 120 degrees to the counterclockwise with a flat-blade screwdriver. 5. Remove the CPU. Figure 4-28 Removing the CPU Installing the CPU The following describes the procedure for installing the CPU (See Figure 4-27 to 4-29). 1.
Page 226 Replacement Procedures NOTE: Apply the silicon grease enough to cover the chip surface using the special applicator. Figure 4-29 Applying silicon grease 5. Install the CPU heat sink and heat sink holder and secure them with the following screws along 1 to 5. M2.5×4.0 BIND screw 6.
Page 227: Vga Heat Sink
Replacement Procedures 4.19 VGA heat sink Removing the VGA heat sink The following describes the procedure for removing the VGA heat sink (See Figure 4-30). 1. Remove the following screws securing the VGA heat sink along 1 to 5. • M2.5×3.0 BIND screw 2.
Page 228 Replacement Procedures Installing the VGA heat sink The following describes the procedure for installing the VGA heat sink (See Figure 4-30). 1. Install the VGA heat sink. NOTE: For details on applying the silicon grease, refer to Installing the CPU. 2.
Page 229 Replacement Procedures 4.20 LCD unit / FL inverter CAUTION: When replacing a LCD, it is required that SVP parameter is set. Update with the latest EC/KBC as described in Appendix H “EC/KBC Rewrite Procedures”. Removing the LCD unit / FL inverter The following describes the procedure for removing the LCD unit and FL inverter (See Figure 4-31 to 4-34).
Page 230 Replacement Procedures 4. Pull out one insulator and peel off the other one adhered to the FL inverter. 5. Disconnect the LCD harnesses from the connectors CN1 on the FL inverter. 6. Disconnect the HV harnesses from the connectors CN2 on the FL inverter. 7.
Page 231 Replacement Procedures 8. Remove the following screws securing the LCD unit. • M2.5x4.0 BINK HEAD screw 9. With the bottom edge of the LCD unit on the display cover, lift only the top edge of the LCD unit. After peeling off the CONDUTIVE tape, disconnect the LCD harness from the connector on the back of the LCD.
Page 232 Replacement Procedures 11. Remove the following screws securing the LCD support (LCD unit side) and remove the LCD supports from the LCD unit. • M2.0x3.0 BINK screw LCD cable LCD logo Inverter M2.0x3.0 Bluetooth BINK Antenna Latch Wireless Antenna LCD support LCD support M2.0x3.0 BINK...
Page 233 Replacement Procedures Installing the LCD unit/FL Inverter The following describes the procedure for installing the LCD unit and FL inverter (See Figure 4-31 to 4-34). 1. Install the LCD supports (LCD unit side) to the LCD and secure them with the following screws.
Page 234 Appendices Satellite P100 Maintenance Manual(960-Q02) App-i...
Page 235 App-ii Satellite P100 Maintenance Manual(960-Q02)
Page 236 Appendix Contents Appendix A Handling the LCD Module ................A-1 Appendix B Board Layout....................B-1 System Board ....................B-1 Function Button Board Back View............... B-4 Modem Board ....................B-5 Touch Pad Board................... B-6 Audio Board....................B-7 VGA Board ....................B-9 Fingerprint Board..................B-11 USB Board ....................
Page 237 C.15 CN15 USB Port-1 ..................10 C.16 CN16 USB Port-2 ..................10 C.17 CN17/ CN20 Fan Connector................10 C.18 CN18 RJ11 Exchange Connector ..............10 C.19 CN19 HDD connector..................10 C.21 CN21 Power Jack Connector ................. 12 C.22 CN22 VGA Power Connector ............... 12 C.23 CN23 DDR2 Connector.................
Page 238 French (FR) Keyboard.................E-5 E 10 Hungary(HU) Keyboard................E-5 E 11 Italian (IT) Keyboard..................E-6 E 12 Korean (KR) Keyboard .................E-6 E 13 Norwegian (NO) Keyboard ................E-7 E 14 Portuguese (PT) Keyboard ................E-7 E 15 Traditional Chinese (TC) Keyboard ..............E-8 E 16 Swedish (SW) Keyboard ................E-8 E 17 Russian (RU) Keyboard ................E-9 E 18 Turkish (TR) Keyboard ................E-9...
Page 239 Appendix F Wiring Diagrams ..................F-1 RGB Monitor ID Wraparound Connector ............ F-1 LAN Loopbak Connector ................F-1 Appendix G BIOS Rewrite Procedures................G-1 Appendix H EC/KBC Rewrite Procedures...............H-1 Appendix I Reliability ..................... I-1 App-vi Satellite P100 Maintenance Manual(960-Q02)
Page 240: Appendix A Handling The Lcd Module
Appendix A Appendix A Handling the LCD Module Precautions for handling the LCD module The LCD module can be easily damaged during assembly or disassembly. Observe the following precautions when handling the LCD module: 1. When installing the LCD module in the LCD cover, be sure to seat it so that it is properly aligned and maximum visibility of the display is maintained.
Page 241 Handling the LCD Module 3. If the panel’s surface gets dirty, wipe it with cotton or a soft cloth. If it is still dirty, try breathing on the surface to create a light condensate and wipe it again. If the surface is very dirty, we recommend a CRT cleaning agent. Apply the agent to a cloth and then wipe the panel’s surface.
Page 242 Handling the LCD Module 5. Glass is used in the panel, so be careful not to drop it or let it strike a hard object, which could cause breakage or cracks. 6. CMOS-LSI circuits are used in the module, so guard against damage from electrostatic discharge.
Page 243 Handling the LCD Module 7. Do not expose the module to direct sunlight or strong ultraviolet rays for long periods. 8. Do not store the module at temperatures below specifications. Cold can cause the liquid crystals to freeze, lose their elasticity or otherwise suffer damage. 9.
Page 244 Handling the LCD Module 10. If you transport the module, do not use packing material that contains epoxy resin (amine) or silicon glue (alcohol or oxide). These materials can release gas that can damage the panel’s polarization. Satellite L20 Maintenance Manual (960-Q01)
Page 245 Handling the LCD Module Satellite P100 Maintenance Manual(960-Q02)
Page 246: Appendix B Board Layout
Appendix B Appendix B Board Layout System Board Figure B-1 System board layout (front) Satellite P100 Maintenance Manual (960-Q02)
Page 247 Board Layout Figure B-2 System board layout (Back) Satellite P100 Maintenance Manual(960-Q02)
Page 248 Board Layout Table B-1-1 System board ICs and connectors Satellite L20 Maintenance Manual(960-Q01)
Page 249 Board Layout Function Button board <Front layout> <Back layout> Figure B-3 Function Button board layout Table B-2 Function Button board connectors Satellite P100 Maintenance Manual(960-Q02)
Page 250 Board Layout Modem board <Front layout> <Back layout> Figure B-3 Modem board layout Table B-3 Modem board connectors Satellite L20 Maintenance Manual(960-Q01)
Page 251 Board Layout Touch Pad Board <Front layout> <Back layout> Figure B-4 Touch pad board layout Table B-4 Touch pad board connectors Satellite P100 Maintenance Manual(960-Q02)
Page 252 Board Layout Audio Board <Front layout> <Back layout> Figure B-5 Audio board layout Satellite L20 Maintenance Manual(960-Q01)
Page 253 Board Layout Table B-5 Audio board connectors Satellite P100 Maintenance Manual(960-Q02)
Page 254 Board Layout VGA Board <Front layout> Figure B-6-4 VGA board layout (front) Satellite L20 Maintenance Manual(960-Q01)
Page 255 Board Layout <Back layout> Figure B-6-2 VGA board layout (back) Table B-6 VGA board connectors B-10 Satellite P100 Maintenance Manual(960-Q02)
Page 256 Board Layout Fingerprint Board <Front layout> <Back layout> Figure B-7 Fingerprint board layout Table B-7 Fingerprint board connectors Satellite L20 Maintenance Manual(960-Q01) B-11...
Page 257 Board Layout USB Board <Front layout> <Back layout> Figure B-8 USB board layout Table B-8 USB board connectors B-12 Satellite P100 Maintenance Manual(960-Q02)
Page 258: Appendix C Pin Assignment
Appendix C Pin Assignment CN1 Bluetooth Connector CONN SMD FFC 20P 1R FR (P0.5, H2.0) PIN No. Signal name PIN No. Signal name WCS_DAT USBP- USBP+ WCS_CLK BT_RESET# I CN2 LCD Panel Connector CONN SMD HOUSING 40P 2R FS (P0.5, H2.6) PIN No.
Page 259 Pin Assignment LVDS_TXL#2 LVDS_TXL2 LVDS_TXL#1 LVDS_TXL1 LVDS_TXL#0 LVDS_TXL0 LVDS_TXLCK# I LVDS_TXLCK PNL_CLK PNL_DAT LVDS_TXU#2 LVDS_TXU2 LVDS_TXU#1 LVDS_TXU1 INVCC0 INVCC0 VADJ PNL_BLON LCDVCC LCDVCC CN3 Button Board Connector CONN SMD FFC 20P 1R FR (P0.5, H2.0) Satellite P100 Maintenance Manual(960-Q02)
Page 260 Pin Assignment PIN No. Signal name PIN No. Signal name NBSWON# BT1# BT2# BT3# BT4# BT_IE# BT_WWW# CAPSLED NUMLED SCRLED EMAIL_LED I CN4 USB Board Connector CONN SMD WAFER 12P 1R MR (P1.25, H1.85) PIN No. Signal name PIN No. Signal name USBP+ USBP-...
Page 261 Pin Assignment CN5 Finger Print Board Connector CONN SMD HOUSING 6P 1R FR (P1.25, H1.85) EP PIN No. Signal name PIN No. Signal name +3VSUS +3VSUS BUSBP+ BUSBP- CN6 Internal K/B Connector CONN SMD FPC 26P 1R FR (P1.0, H2.2) PIN No.
Page 262 Pin Assignment CN7 Touchpad Board Connector CONN SMD FFC 6P 1R FR (P1.0, H1.95) PIN No. Signal name PIN No. Signal name +5V_TP +5V_TP TPDATA TPCLK CN8 RTC Battery Connector CONN SMD HEADER 2P MS (P1.25) PIN No. Signal name PIN No.
Page 263 Pin Assignment A_CAD14 A_CC/BE1# A_CPAR A_CPERR# A_CGNT# A_CINT# A_VCC AVPP A_CCLK A_CIRDY# A_CC/BE2# A_CAD18 A_CAD20 A_CAD21 A_CAD22 A_CAD23 A_CAD24 A_CAD25 A_CAD26 A_CAD27 A_CAD29 A_RSVD_D2 A_CCLKRUN# I A_CCD1# A_CAD2 A_CAD4 A_CAD6 A_RSVD_D14 I/O A_CAD8 A_CAD10 A_CVS1# A_CAD13 A_CAD15 A_CAD16 A_RSVD_A18 A_CBLOCK# A_CSTOP# A_CDEVSEL# I A_VCC...
Page 264 Pin Assignment A_CSERR# A_CREQ# A_CC/BE3# A_CAUDIO A_CSTSCHG A_CAD28 A_CAD30 A_CAD31 A_CCD2# CN10 Speaker Connector CONN SMD HD 4P 1R MR (P1.25, H3.2) PIN No. Signal name PIN No. Signal name INSPKR+ INSPKR- INSPKL+ INSPKL- AUDGND AUDGND CN11 S-Video Connector CONN DIP MINI-DIN 4P FR (P1.0, H10.5) PIN No.
Page 265 Pin Assignment CONN DIP D-SUB 15P 2R FR (P0.76) L-F PIN No. Signal name PIN No. Signal name CRT_R CRT_G CRT_B +5V_CRT CRT_SENSE# O CRTDDAT CRTHSYNC CRTVSYNC I CRTDCLK CN13 DVI Connector CONN D-SUB DIP 30P 3R FR (P1.9, H10.04) PIN No.
Page 266 Pin Assignment DVI_TX0- DVI_TX0+ DVI_CLK+ DVI_CLK- CN14 RJ11/RJ45 Connector CONN RJ11/RJ45 14P2R FR (L: G, R: Y, H10.1) LF PIN No. Signal name PIN No. Signal name +3V_S5 LANACT_LED# --- X-TX3N X-TX3P X-TX1N X-TX2N X-TX2P X-TX1P X-TX0N X-TX0P +3V_S5 LAN_LINK# TIPL_R RINGL_R CN15 USB Port-1...
Page 267 Pin Assignment PIN No. Signal name PIN No. Signal name USBPOWER --- USBP- USBP+ CN16 USB Port-2 CONN DIP (USB) 4P 1R MR (L=13.60, H5.70) PIN No. Signal name PIN No. Signal name USBPOWER --- USBP- USBP+ CN17/CN20 Fan Connector CONN SMD WAFER, 3P, 1R, MS (P1.25) PIN No.
Page 268 Pin Assignment CONN SMD HEADER 2P 1R MR (P1.25, H1.95) PIN No. Signal name PIN No. Signal name TIPL RINGL CN19 HDD Connector CONN DIP HS 22P 1R FR (P1.27, H13.99) PIN No. Signal name PIN No. Signal name SATA_TXP0 I SATA_TXN0 I SATA_RXN0 O SATA_RXP0 O...
Page 269 Pin Assignment CN22 VGA Power Connector CONN SMD HEADER 10P MS (P1.5, H5.0) PIN No. Signal name PIN No. Signal name CN23 DDR2 Connector IC SKT DDRII SO-DIMM (200P, H4.0, RVS) EP PIN No. Signal name PIN No. Signal name SM_VREF_DIMM --- SM_DQ4 SM_DQ1...
Page 270 Pin Assignment SM_DQ6 SM_DQ2 SM_DQ3 SM_DQ13 SM_DQ14 SM_DQ12 SM_DQ8 SM_DM1 SM_DQS#1 SM_CLK0 SM_DQS1 SM_CLK#0 SM_DQ9 SM_DQ10 SM_DQ15 SM_DQ11 SM_DQ21 SM_DQ20 SM_DQ17 SM_DQ16 SM_DQS#2 PM_EXTTS#0 O SM_DQS2 SM_DM2 SM_DQ23 SM_DQ18 SM_DQ19 SM_DQ22 SM_DQ24 SM_DQ29 Satellite P100 Maintenance Manual(960-Q02)
Page 271 Pin Assignment SM_DQ25 SM_DQ28 SMA_DM3 SM_DQS#3 SM_DQS3 SM_DQ26 SM_DQ30 SM_DQ27 SM_DQ31 M_CKE0 M_CKE1 +1.8VSUS +1.8VSUS SM_BS2 +1.8VSUS +1.8VSUS SM_MA12 SM_MA11 SM_MA9 SM_MA7 SM_MA8 SM_MA6 +1.8VSUS +1.8VSUS SM_MA5 SM_MA4 SM_MA3 SM_MA2 SM_MA1 SM_MA0 +1.8VSUS +1.8VSUS SM_MA10 SM_BS1 SM_BS0 SM_RAS# SM_WE# M_CS#0 Satellite P100 Maintenance Manual(960-Q02)
Page 272 Pin Assignment +1.8VSUS +1.8VSUS SM_CAS# M_ODT0 M_CS#1 SM_MA13 +1.8VSUS +1.8VSUS M_ODT1 SM_DQ35 SM_DQ32 SM_DQ37 SM_DQ36 SM_DQS#4 SM_DM4 SM_DQS4 SM_DQ33 SM_DQ38 SM_DQ34 SM_DQ39 SM_DQ44 SM_DQ40 SM_DQ45 SM_DQ41 SM_DQS#5 SM_DM5 SM_DQS5 SM_DQ42 SM_DQ43 SM_DQ46 SM_DQ47 SM_DQ48 SM_DQ52 Satellite P100 Maintenance Manual(960-Q02)
Page 273 Pin Assignment SM_DQ49 SM_DQ53 SM_CLK1 SM_CLK#1 SM_DQS#6 SM_DQS6 SM_DM6 SM_DQ50 SM_DQ54 SM_DQ51 SM_DQ55 SM_DQ56 SM_DQ61 SM_DQ60 SM_DQ57 SM_DM7 SM_DQS#7 SM_DQS7 SM_DQ62 SM_DQ58 SM_DQ59 SM_DQ63 CGDAT_SMB CGCLK_SMB CN24 DDR2 Connector Satellite P100 Maintenance Manual(960-Q02)
Page 274 Pin Assignment IC SKT DDRII SO-DIMM (200P, H8.0MM, 1.8V) PIN No. Signal name PIN No. Signal name SM_VREF_DIMM --- SM_DQ4 SM_DQ1 SM_DQ0 SM_DQ5 SM_DM0 SM_DQS#0 SM_DQS0 SM_DQ7 SM_DQ6 SM_DQ2 SM_DQ3 SM_DQ13 SM_DQ14 SM_DQ12 SM_DQ8 SM_DM1 SM_DQS#1 SM_CLK0 SM_DQS1 SM_CLK#0 SM_DQ9 SM_DQ10 SM_DQ15 SM_DQ11...
Page 275 Pin Assignment SM_DQ17 SM_DQ16 SM_DQS#2 PM_EXTTS#0 O SM_DQS2 SM_DM2 SM_DQ23 SM_DQ18 SM_DQ19 SM_DQ22 SM_DQ24 SM_DQ29 SM_DQ25 SM_DQ28 SMA_DM3 SM_DQS#3 SM_DQS3 SM_DQ26 SM_DQ30 SM_DQ27 SM_DQ31 M_CKE0 M_CKE1 +1.8VSUS +1.8VSUS SM_BS2 +1.8VSUS +1.8VSUS SM_MA12 SM_MA11 SM_MA9 SM_MA7 Satellite P100 Maintenance Manual(960-Q02)
Page 276 Pin Assignment SM_MA8 SM_MA6 +1.8VSUS +1.8VSUS SM_MA5 SM_MA4 SM_MA3 SM_MA2 SM_MA1 SM_MA0 +1.8VSUS +1.8VSUS SM_MA10 SM_BS1 SM_BS0 SM_RAS# SM_WE# M_CS#0 +1.8VSUS +1.8VSUS SM_CAS# M_ODT0 M_CS#1 SM_MA13 +1.8VSUS +1.8VSUS M_ODT1 SM_DQ35 SM_DQ32 SM_DQ37 SM_DQ36 SM_DQS#4 SM_DM4 SM_DQS4 SM_DQ33 SM_DQ38 SM_DQ34 SM_DQ39 SM_DQ44 Satellite P100 Maintenance Manual(960-Q02)
Page 277 Pin Assignment SM_DQ40 SM_DQ45 SM_DQ41 SM_DQS#5 SM_DM5 SM_DQS5 SM_DQ42 SM_DQ43 SM_DQ46 SM_DQ47 SM_DQ48 SM_DQ52 SM_DQ49 SM_DQ53 SM_CLK1 SM_CLK#1 SM_DQS#6 SM_DQS6 SM_DM6 SM_DQ50 SM_DQ54 SM_DQ51 SM_DQ55 SM_DQ56 SM_DQ61 SM_DQ60 SM_DQ57 SM_DM7 SM_DQS#7 SM_DQS7 Satellite P100 Maintenance Manual(960-Q02)
Page 278 Pin Assignment SM_DQ62 SM_DQ58 SM_DQ59 SM_DQ63 CGDAT_SMB CGCLK_SMB CN25 1394 Port CONN DIP (1394) 4P 2R FR(P1.6,H5.6) L-F PIN No. Signal name PIN No. Signal name 1394_TPB0- O 1394_TPB0+ O 1394_TPA0- O 1394_TPA0+ O CN26 ODD Connector CONN DIP HOUSING50P 4R FR (P0.8, H6.0) PIN No.
Page 279 Pin Assignment PDD6 PDD10 PDD5 PDD11 PDD4 PDD12 PDD3 PDD13 PDD2 PDD14 PDD1 PDD15 PDD0 PDDREQ PDIOR# PDIOW# PIORDY PDDACK# IRQ14 PDA1 PDIAG# PDA0 PDA2 PDCS1# PDCS3# ODDLED# +5V_ODD +5V_ODD +5V_ODD +5V_ODD +5V_ODD RCSEL Satellite P100 Maintenance Manual(960-Q02)
Page 280 Pin Assignment CN27 VGA Interface Connector CONN SMD HS 180P FR (P0.5, H4.15) EP PIN No. Signal name PIN No. Signal name PEG_TXP0 PEG_RXP0 PEG_TXN0 PEG_RXN0 PEG_TXP1 PEG_RXP1 PEG_TXN1 PEG_RXN1 PEG_TXP2 PEG_RXP2 PEG_TXN2 PEG_RXN2 PEG_TXP3 PEG_RXP3 PEG_TXN3 PEG_RXN3 PEG_TXP4 PEG_RXP4 PEG_TXN4 PEG_RXN4 PEG_TXP5...
Page 281 Pin Assignment PEG_TXP7 PEG_RXP7 PEG_TXN7 PEG_RXN7 PEG_TXP8 PEG_RXP8 PEG_TXN8 PEG_RXN8 PEG_TXP9 PEG_RXP9 PEG_TXN9 PEG_RXN9 PEG_TXP10 PEG_RXP10 PEG_TXN10 PEG_RXN10 PEG_TXP11 PEG_RXP11 PEG_TXN11 PEG_RXN11 PEG_TXP12 PEG_RXP12 PEG_TXN12 PEG_RXN12 PEG_TXP13 PEG_RXP13 PEG_TXN13 PEG_RXN13 PEG_TXP14 PEG_RXP14 PEG_TXN14 PEG_RXN14 Satellite P100 Maintenance Manual(960-Q02)
Page 282 Pin Assignment PEG_TXP15 PEG_RXP15 PEG_TXN15 PEG_RXN15 27M_VGA PECLK_VGA 27MSS_VGA PECLK_VGA# PLTRST# SYSFANON# EXT_CRTDDCCLK MAINON EXT_CRTDDCDAT DVI_HPD HWPG_VGA DVI_DDCDAT MBDATA DVI_DDCCLK MBCLK EV_BLON LVDS_PNLCLK EV_PNLON LVDS_PNLDAT EXT_HSYNC EXT_VSYNC EXT_VGA_RED EXT_VGA_GRN +2.5V EXT_VGA_BLU +2.5V +2.5V Satellite P100 Maintenance Manual(960-Q02)
Page 283 Pin Assignment +2.5V EXT_TV_Y/G +2.5V EXT_TV_C/R EXT_DVI_TX2+ EXT_DVI_TX0+ EXT_DVI_TX2- EXT_DVI_TX0- EXT_DVI_CLK+ EXT_DVI_TX1+ EXT_DVI_CLK- EXT_DVI_TX1- EXT_LVDS_TXL0 EXT_LVDS_TXU0 EXT_LVDS_TXL#0 EXT_LVDS_TXU#0 EXT_LVDS_TXL1 EXT_LVDS_TXU1 EXT_LVDS_TXL#1 EXT_LVDS_TXU#1 EXT_LVDS_TXL2 EXT_LVDS_TXU2 EXT_LVDS_TXL#2 EXT_LVDS_TXU#2 EXT_LVDS_TXLCK EXT_LVDS_TXUCK EXT_LVDS_TXLCK# O EXT_LVDS_TXUCK# O Satellite P100 Maintenance Manual(960-Q02)
Page 284 Pin Assignment CN28 Modem Board Connector CONN SMD HEADER 12P, 2R, MS (P0.8, H2.4) PIN No. Signal name PIN No. Signal name PWRCLKN PWRCLKP DIB_DATAP DIB_DATAN I/O CN29 New Card Connector CONN SMD HEADER 26P1R MR (P1.0, H4.75) PIN No. Signal name PIN No.
Page 285 Pin Assignment WAKW# +NEW_3VAUX PERST# +NEW_3V +NEW_3V NEW_CLKREQ# O CPPE# PECLK_NEW# PECLK_NEW PCIE_RXN PCIE_RXP PCIE_TXN PCIE_TXP CN30 Mini Card Connector CONN DIP HOUSING 52P 2R FR (P0.8, H5.6) EP PIN No. Signal name PIN No. Signal name WAKE# WCS_DATR WCS_CLKR +1.5V MINI_CLKREQ# O PECLK_MINI#...
Page 286 Pin Assignment RF_EN PLTRST# PCIE_RXN +3VSUS PCIE_RXP +1.5V PCLK_SMB PCIE_TXN PDAT_SMB PCIE_TXP USBP- USBP+ LED_WWAN# --- WL_LED BT_LED +1.5V CN31 5 in 1 Card Connector CONN HEADER 46P 2R MS (P0.8, H6.2) Signal name Signal name MSBS_SDCMD_SMWE# O Satellite P100 Maintenance Manual(960-Q02)
Page 287 Pin Assignment MSD1_SDD1_SMD1 MSD0_SDD0_SMD0 MSD2_SDD2_SMD2 MS_CD# MSD3_SDD3_SMD3 MSCK_SDCK_SMWP# VCC_FM MSD2_SDD2_SMD2 MSD3_SDD3_SMD3 MSBS_SDCMD_SMWE# O VCC_FM MSCK_SDCK_SMWP# MSD0_SDD0_SMD0 MSD1_SDD1_SMD1 SD_CD# XD_CD# SM_R/B# SM_RE# SDWP_SMCE# SM_CLE SM_ALE MSBS_SDCMD_SMWE# I/O MSCK_SDCK_SMWP# MSD1_SDD1_SMD0 MSD1_SDD1_SMD1 MSD1_SDD1_SMD2 MSD3_SDD3_SMD3 SM_D4 SM_D5 SM_D6 SM_D7 VCC_FM SDWP_SMCE# CN32 Audio Board Connector Satellite P100 Maintenance Manual(960-Q02)
Page 288 Pin Assignment CONN SMD FFC 20P 1R FR (P0.5, H2.0) PIN No. Signal name PIN No. Signal name SPKL SPKR PORT_B_L PORT_B_R MIC_R MIC_L SENSEA SENSEB AUD_VOL IRRX WLAN_LED O Kill_LED LID591# WL_SW# SPKPLG SPDIF_OUT O +3V_S5 +5V_SP CN33 Speaker LED Connector CONN SMD HOUSING 4P 1R FR (P1.25, H1.85) PIN No.
Page 289 Pin Assignment TEMP_MBAT O DATA Satellite P100 Maintenance Manual(960-Q02)
Page 290 Appendix. D Appendix D Display Codes Display Codes Table D-1 Scan codes (set 1 and set 2) (1/4) Code set 1 Code set 2 Keytop Note Make Break Make Break ‘ ~ 7 & BkSp Satellite P100 Maintenance Manual(960-Q02)
Page 291 Display codes Table D-1 Scan codes (set 1 and set 2) (2/4) Code set 1 Code set 2 Keytop Note Make Break Make Break Caps Lock ‘ “ Enter Shift (L) No.102 , < . > Shift (R) Satellite P100 Maintenance Manual(960-Q02)
Page 292 Display codes Table D-1 Scan codes (set 1 and set 2) (3/4) Code set 1 Code set 2 Keytop Note Make Break Make Break Ctrl Alt (L) Space ALT (R) ← Home ↑ ↓ PgUp PgDn → Satellite L20 Maintenance Manual (960-497)
Page 293 Display codes Table D-1 Scan codes (set 1 and set 2) (4/4) Code set 1 Code set 2 Keytop Note Make Break Make Break PrintSc Pause — — — — Notes: 1. * Scan codes differ by mode. 2. * Scan codes differ by overlay function. 3.
Page 294 Display codes Table D-2 Scan codes with left Shift key Code set 1 Code set 2 Make Break Make Break E0 AA E0 35 E0 B5 E0 2A E0 F0 12 E0 4A E0 F0 4A E0 12 E0 AA E0 52 E0 D2 E0 2A E0 F0 12 E0 70 E0 F0 70 E0 12 E0 AA E0 53 E0 D3 E0 2A E0 F0...
Page 295 Display codes Table D-3 Scan codes in Numlock mode Code set 1 Code set 2 Make Break Make Break E0 2A E0 52 E0 D2 E0 AA E0 12 70 E0 F0 E0 F0 12 E0 2A E0 53 E0 D3 E0 AA E0 12 71 E0 F0 E0 F0 12...
Page 296 Display codes Table D-5 Scan codes in overlay mode Code set 1 Code set 2 Keytop Make Break Make Break (–) Table D-6 No.124 key scan code Code set 1 Code set 2 Shift Make Break Make Break Prt Sc Common Ctrl + Shift +...
Page 297 Display codes Table D-7 No.126 key scan code Shift Code set 1 Code set 2 Make Make Pause Common* E1 1D E1 F0 Ctrl* E0 46 7E E0 F0 *: This key generates only make codes. Satellite P100 Maintenance Manual(960-Q02)
Page 298 Appendix E Key Layout Appendix E Keyboard Layout United States (US) Keyboard Figure E-1 US Keyboard layout United Kingdom (UK) Keyboard Figure E-2 UK Keyboard layout Satellite P100 Maintenance Manual(960-Q02)
Page 299 Keyboard Layout Arabia (AR) Keyboard Figure E-3 AR Keyboard layout Belgium (BB) Keyboard Figure E-4 BB Keyboard layout Satellite P100 Maintenance Manual(960-Q02)
Page 300 Keyboard Layout Appendices Czech (CZ) Keyboard FigureE-5 CZ Keyboard layout German (GR) Keyboard Figure E-6 GR Keyboard layout Satellite Denver Maintenance Manual(P100)
Page 301 Keyboard Layout Danish (DK) Keyboard Figure E-7 DK Keyboard layout Spanish (SP) Keyboard Figure E-8 SP Keyboard layout Satellite P100 Maintenance Manual(960-Q02)
Page 302 Keyboard Layout Appendices French (FR) Keyboard Figure E-9 FR Keyboard layout E.10 Hungary(HU) Keyboard Figure E-10 HUR Keyboard layout Satellite Denver Maintenance Manual(P100)
Page 303 Keyboard Layout E.11 Italian (IT) Keyboard Figure E-11 IT Keyboard layout E.12 Korean (KR) Keyboard Figure E-12 KR Keyboard layout Satellite P100 Maintenance Manual(960-Q02)
Page 304 Keyboard Layout Appendices E.13 Norwegian (NO) Keyboard Figure E-13 NO Keyboard layout E.14 Portuguese (PT) Keyboard Figure E-14 PT Keyboard layout Satellite Denver Maintenance Manual(P100)
Page 305 Keyboard Layout E.15 Traditional Chinese (TC) Keyboard Figure E-15 TC Keyboard layout E.16 Swedish (SW) Keyboard Figure E-16 SW Keyboard layout Satellite P100 Maintenance Manual(960-Q02)
Page 306 Keyboard Layout Appendices E.17 Russian (RU) Keyboard Figure E-17 RU Keyboard layout E.18 Turkish (TR) Keyboard Figure E-18 TR Keyboard layout Satellite Denver Maintenance Manual(P100)
Page 307 Keyboard Layout E.19 Japanese (JP) Keyboard Figure E-19 JP Keyboard layout E.20 Swiss-German(SL) Keyboard Figure E-20 SL Keyboard layout Satellite P100 Maintenance Manual(960-Q02) E-10...
Page 308 Keyboard Layout Appendices E.21 Hebrew Keyboard Figure E-21 Keyboard layout E.22 Greek Keyboard Figure E-22 GK Keyboard layout Satellite Denver Maintenance Manual(P100) E-11...
Page 309: Wiring Diagrams
Appendix F Appendix F Wiring Diagrams RGB Monitor ID Wraparound connector (1) RED (2) GREEN GREEN (2) (3) BLUE BLUE (4) NC (5) GND (6) GND (7) GND (8) GND (9) 5V (10) GND (10) (11) NC (11) (12) SDA (12) (13) HSYNC HSYNC (13)
Page 310 Wiring Diagrams Satellite P100 Maintenance Manual(960-Q02)
Page 311: Appendix G Bios Rewrite Procedures
Appendix G Appendix G BIOS Rewrite Procedures This Appendix explains how to rewrite the system BIOS program when you update the system BIOS. Tools To rewrite the BIOS, you need the following tool: BIOS/EC/KBC rewriting disk USB doggle Rewriting the BIOS 1.
Page 312 Appendix H Appendix H EC/KBC Rewrite Procedures Same as BIOS rewrite Procedures, please refer appendix G Satellite P100 Maintenance Manual(960-Q02)
Page 313: Appendix I Reliability
Appendix I Reliability Appendix I Reliability The following table shows MTBF (Mean Time Between Failures) in maximum configuration. Table I-1 MTBF Component Time (hours) System 6678.69 Satellite P100 Maintenance Manual(960-Q02)
Page 314 Reliability Satellite L10 Maintenance Manual(960-Q01)

Toshiba Satellite P100 Series Maintenance Manual

Table of Contents

Chapter 1 Hardware Overview

Table of Contents

Chapter 2 Troubleshooting Procedures

Table of Contents

Chapter 3 Test Program for Field

Chapter 4 Replacement Procedures

Table of Contents

Appendix A Handling the Lcd Module

Appendix B Board Layout

Appendix C Pin Assignment

Appendix G Bios Rewrite Procedures

Appendix I Reliability

Quick Links

Chapters

Troubleshooting

Related Manuals for Toshiba Satellite P100 Series

Summary of Contents for Toshiba Satellite P100 Series

Table of Contents