Vcr Plus+ ® Timer Programing; Express Timer Programing; 24Hr Quick Programing - JVC SR-V101US Instructions Manual

VCR Plus+ Timer Programing
®
The PlusCode programing numbers are
the numbers next to the program in
most TV listing.
Load a cassette with the record safety
tab intact. If not, set "REC SAFETY" to
"OFF" ( pg. 19). The VCR turns on,
and the counter is reset, automatically.
A
Press PROG. on the Remote to access
the PlusCode No. screen.
PLUSCODE NO.
PRESS NUMBER KEY (0–9)
PRESS (+/–) TO SET
EXPRESS PROGRAMMING
PRESS (PROG.) TO END
VCR PLUS+ SYSTEM
B
Press the appropriate Number keys
to input the PlusCode number, then
SHUTTLE PLUS e
press OK or
setting is accurate on the Program screen.
PLUSCODE NO.
1 2 3 4 5 6 7 8
PRESS NUMBER KEY (0–9)
THEN (OK)
PRESS (PROG.) TO END
VCR PLUS+ SYSTEM
● If the Guide Channel Set screen
appears after pressing OK, press the
Number keys, CH+/– or
PLUS rt
to input the number of the
channel on which the broadcast for
the PlusCode number is received on
the VCR, then press OK.
● To set the tape speed, press SP/EP.
● To change the stop time, press STOP+/–.
● To timer-record daily (Sunday–Saturday) or weekly serials,
press DAILY (Number key "8") or WEEKLY (Number key
"9"). Pressing the button again makes the "DAILY" or
"WEEKLY" display disappear.
● If you made a mistake, press CANCEL to access the PlusCode
No. screen again.
● If an incorrect PlusCode number or the one for a broadcast
already finished has been input, "ERROR" is displayed for
about 5 seconds, then the PlusCode No. screen reappears.
C
Press OK or PROG..
● If "PROGRAM NOT COMPLETED PROGRAM OVERLAP"
appears, see "Program Overlap Warning Display"
( pg. 17).
D
Press TIMER. The VCR turns off automatically and "
displayed on the display panel.

Express Timer Programing

Load a cassette with the record safety tab intact. If not, set "REC
SAFETY" to "OFF" ( pg. 19). The VCR turns on, and the counter
is reset, automatically.
A
Press PROG. on the Remote to access the PlusCode No. screen.
B
Press START+/– once to access
Program screen.
Press START+/–, STOP+/–, DATE+/– or
CH+/– repeatedly to enter the start
time, stop time, date or channel.
● Press and hold START+/– or STOP+/–
to increase the time in 30-minute
intervals.
. Check to make sure the
PROGRAM 1
(PLUSCODE NO. 12345678)
START STOP
8:00PM 10:00PM
DATE CH
12/24/04 12 SP
FRI
PRESS (8=DAILY, 9=WEEKLY
STOP+/– = STOP TIME, SP/EP)
PRESS (PROG.) TO END
GUIDE CHANNEL SET
GUIDE CH : 12
SHUTTLE
VCR CH : – – –
PRESS NUMBER KEY (0–9)
OR ( , ), THEN (OK)
PRESS (PROG.) TO END
#
PROGRAM 1
START STOP
– –:– –AM – –:– –AM
DATE CH
– –/– –/– – – – – SP
PRESS (+/–, SP/EP, 8=DAILY
9=WEEKLY), THEN (0K)
PRESS (PROG.) TO END
● To set the tape speed, press SP/EP.
● To timer-record daily (Sunday–
Saturday) or weekly serials, press
DAILY (Number key "8") or WEEKLY
(Number key "9"). Pressing the
button again makes the "DAILY" or
"WEEKLY" display disappear.
C
Press OK or PROG..
● If "PROGRAM NOT COMPLETED PROGRAM OVERLAP"
appears, see "Program Overlap Warning Display"
( pg. 17).
D
Press TIMER. The VCR turns off automatically and "
displayed on the display panel.

24HR Quick Programing

You can program a timer recording that starts within 24 hours
using the JOG dial on the VCR.
Load a cassette with the record safety tab intact or set "REC
SAFETY" to "OFF" (
is reset, automatically.
A
Press 24HR QUICK PROGRAM on the
VCR. The start time indicator (
blinking on the display panel.
B
Turn the JOG dial to the left or right to set
the start time.
● One click stop of the JOG dial changes
the time in 5-minute intervals.
C
Push the JOG dial. The stop time
indicator (
display panel. Turn the JOG dial to the
left or right to set the stop time.
D
Push the JOG dial. Turn the JOG dial to
the left or right to select the channel.
● To set the tape speed, press SP/EP. The
current setting for the tape speed appears on the display
panel for about 5 seconds. Press SP/EP again to change the
setting while tape speed is displayed.
E
To engage timer recording standby mode, press 24HR QUICK
PROGRAM. The VCR turns off automatically and "
displayed on the display panel.
NOTES:
● If "Err" appears on the display panel, repeat the above steps
again.
● When a menu screen is shown, you cannot use 24HR Quick
Programing function. Press MENU to return to normal screen,
and try again.
● You can use 24HR Quick Programing function also when the
VCR is turned off.
" is
● For 24HR Quick Programing function, the program overlap
warning display does not appear even if some programs overlap
each other.
To use the VCR while it is in timer recording standby
mode
Press TIMER, then press POWER 1. After you use the VCR, press
TIMER again to put the VCR into timer recording standby mode.
— 16 —
pg. 19). The VCR turns on, and the counter
) starts
) starts blinking on the
PROGRAM 1
START STOP
8:00AM 9:00AM
DATE CH
12/24/04 110 SP
FRI
PRESS (+/–, SP/EP, 8=DAILY
9=WEEKLY), THEN (0K)
PRESS (PROG.) TO END
" is
#
Start time
Stop time
Channel number
" is
#