Troubleshooting; Care And Maintenance; Specifications - Stanley TGC11 Instruction Manual

3. W hen "0" is reached, the LCD screen will display the following; and the vehicle is ready to start.
4. C rank the engine using manufacturer' s guidelines, typically in 3 to 5 second bursts. The function requires a resting/cooling
period between attempts. Wait 4 to 5 minutes before a second attempt at starting the engine, if needed.
5. T o stop the process, press the engine start switch to turn it off (O). The unit will revert to charging mode. To end the charging
process, turn the unit off using the main on/off switch.
When disconnecting charger, disconnect AC cord, remove clamp from vehicle chassis, and then remove clamp from battery
terminal.
CAUTION: TO REDUCE THE RISK OF PROPERTY DAMAGE:
• Vehicles that have on-board computerized systems may be damaged if vehicle battery is started using the engine start function.
Before attempting to use this function, read the vehicle' s owner' s manual to confirm that external-starting assistance is suitable.
• Excessive engine cranking can damage the vehicle's starter motor. If the engine fails to start after the number of attempts
recommended by battery manufacturer, discontinue the procedure and contact a qualified technician to investigate why the
engine did not start.
using the Portable Inflator
The built-in inflator is the ultimate inflator for most vehicle tires, trailer tires and recreational inflatables. The inflator hose with
tire fitting is stored on the right side of the unit. The air pressure gage is located in the front of the inflator hose. The inflator power
switch is located on the bottom left of the control panel.
The inflator may be used by removing the air hose from the storage hatch and if required, fitting an appropriate nozzle to the air
hose. Return hose to the storage hook after use.
InflatIng tIres or Products WIth ValVe stems
1. Screw the SureFit™ nozzle connector into the valve stem. Do not overtighten.
2. Plug the battery charger' s power cord into an AC outlet and press the main power on/off switch to turn the unit on.
3. T urn on the inflator power switch (I). The LCD screen will display the following flashing inflator mode icon:
4. C heck pressure with the pressure gage.
5. T urn off the inflator power switch (O).
6. W hen desired pressure is reached, unscrew the SureFit™ nozzle connector from the valve stem.
Note:
The unit will revert to charging mode if the unit is connected to the battery. To end the charging process, turn the unit off using the main on/off
switch. When disconnecting charger, disconnect AC cord, remove clamp from vehicle chassis, and then remove clamp from battery terminal.
7. A llow unit to cool before storing away.
8. S tore inflator hose and tire fitting on the storage hook on the side of the unit.
InflatIng other Inflatables WIthout ValVe stems
Inflation of other items requires use of one of the adapters (nozzles).
1. S elect the appropriate adapter nozzle.
2. S crew the adapter (i.e. needle) into the Surefit™ nozzle connector. Do not overtighten.
3. I nsert adapter (i.e., needle) into item to be inflated.
4. T urn on the inflator power switch (I) and inflate to desired pressure or fullness.
IMPORTANT NOTE: Small items such as volleyballs, footballs, etc. inflate very rapidly. Do not over-inflate.
5. S witch the inflator power switch off (O).
6. R emove adapter.
Note:
The unit will revert to charging mode if the unit is connected to the battery. To end the charging process, turn the unit off using the main on/off
switch. When disconnecting charger, disconnect AC cord, remove clamp from vehicle chassis, and then remove clamp from battery terminal.
7. A llow unit to cool before storing away.
8. S tore inflator hose and tire fitting on the storage hook on the side of the unit.
WARNING: TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE: FOLLOW ALL SAFETY INSTRUCTIONS FOUND IN
THE "SPECIFIC SAFETY INSTRUCTIONS FOR INFLATORS" SECTION OF THIS INSTRUCTION MANUAL.

trOuBlEShOOtINg

Unit Fails to Charge Battery
• Check that the charger is properly connected to a live 120 volt AC outlet.
• I f the battery to be charged has fallen below 2 volts, the battery cannot be recharged with this charger.
Engine Start Fails to Start Engine
• Check that the charger is properly connected to a live 120 volt AC outlet.
• Make sure unit' s engine start switch is in the on position.
• Make sure a proper polarity cable connection has been established.
Portable Inflator will not inflate
• Make sure the inflator power switch is in the on position.
• Make sure the SureFit™ nozzle connector is securely screwed into the valve stem when attempting to inflate tires; or nozzle
(adapter) is securely inserted into connector (chuck) on all other inflatables.

CArE AND mAINtENANCE

Storage
• Store the unit in a clean, dry, cool place when not in use.
• Clean the unit casing and cords (as necessary) with a dry (or slightly damp) cloth. Ensure that unit is completely disconnected
from battery and power source before cleaning.
• To maintain the operating condition and maximize the life of the charger cords, always coil them loosely for storage. Do not wrap
them around the unit or crimp them with a tight band.
ONE YEAR LIMITED WARRANTY
The manufacturer warrants this product against defects in materials and workmanship for a period of ONE (1) YEAR from the date
of retail purchase by the original end-user purchaser ("Warranty Period").
If there is a defect and a valid claim is received within the Warranty Period, the defective product can be replaced or repaired in
the following ways: (1) Return the product to the retailer where product was purchased for an exchange (provided that the store
is a participating retailer). Returns to retailer should be made within the time period of the retailer' s return policy for exchanges
only (usually 30 to 90 days after the sale). Proof of purchase may be required. Please check with the retailer for their specific return
policy regarding returns that are beyond the time set for exchanges. (2) Return the product to the manufacturer for repair or
replacement at manufacturer' s option. Proof of purchase may be required by manufacturer.
This warranty does not apply to accessories, bulbs, fuses and batteries; defects resulting from normal wear and tear, accidents;
damages sustained during shipping; alterations; unauthorized use or repair; neglect, misuse, abuse; and failure to follow
instructions for care and maintenance for the product.
This warranty gives you, the original retail purchaser, specific legal rights and you may have other rights which vary from state to
state or province to province. This product is not intended for commercial use.

SPECIFICAtIONS

Input: 120VAC, 60Hz, 9.5A
1500W engine start
Output: 12VDC, 40A
110A engine start (5 minutes off; 5 seconds on)
Inflator Maximum Pressure: 120 PSI