JVC HR-DD858E/EH Instructions Manual page 6

6
EN
Auto Set Up results appear on the front display panel
A
When both auto channel set and auto
clock set have been completed success-
fully the correct current time will be
displayed after the OK button is pressed in
step 6 on page 5.
You can check if the Guide Program numbers have been set correctly when you perform S
( pg. 26); if the correct channel position number is displayed in step 3, this confirms that the Guide Program number for the
S V number you enter in step 2 has been set correctly.
HOW IEW
A If both auto channel set and auto clock set have been performed successfully:
1 Turn on the TV and select its VIDEO channel or AV mode, then make sure that all necessary stations have been stored in
the recorder's memory by using the TV PROG button(s).
If station names (ID —
the top left corner of the screen for about 5 seconds when the recorder is tuned to a different station.
If you want to set the tuner manually such as to add or skip channels, to change channel positions, or to set or change
station names, see pages 48 – 52.
B
If auto channel set has succeeded but auto clock set has not:
1 Turn on the TV and select its VIDEO channel or AV mode, then make sure that all necessary stations have been stored in
the recorder's memory by using the TV PROG button(s).
If station names (ID —
the top left corner of the screen for about 5 seconds when the recorder is tuned to a different station.
If you want to set the tuner manually such as to add or skip channels, to change channel positions, or to set or change
station names, see pages 48 – 52.
2 Perform "Clock Set" on page 54.
C
If both auto channel set and auto clock set have failed:
1
Make sure the TV aerial cable is connected properly to the recorder and turn off the recorder power once, then turn the
recorder power back on again.
The Country Set display appears on the front display panel and/or on the screen; perform steps 2 – 6 on pages 4 – 5 again.
IMPORTANT
In certain reception conditions, station names may not be stored correctly, and auto Guide Program Number Set may not
work properly. If the Guide Program numbers are not set properly, when you timer-record a TV programme using S
the recorder will record a TV programme of a different station. When programming the timer using S
check whether the channel position on which your recorder receives the broadcasting station you wish to record is selected
( pg. 26, "S V
HOW IEW
Your video recorder memorizes all detected stations even if reception of some of them is poor. In these cases picture quality
may be poor. To delete those stations with an unacceptable picture
For RF connection users: In certain reception conditions, the Video Channel may not be set correctly and interference may
appear in the TV picture while the recorder's power is on. Set your Video Channel manually.
INFORMATION
Language for the on-screen display
Auto Set Up also selects the language automatically for the on-screen display depending on the Country setting you have made
in step 2 on page 4 (unless you have selected BELGIUM or SUISSE), as shown below.
SUOMI [ SUOMI
PORTUGAL [ ENGLISH
DEUTSCHLAND [ DEUTSCH
NORGE [ NORSK
If you want to change the language setting manually,
Just Clock
Your recorder is equipped with the Just Clock function which provides accurate time keeping through automatic adjustments at
regular intervals, by reading data from a PDC signal. If you want to take advantage of this function, simply set it to "ON".
"Just Clock" on page 54.
B
When auto channel set has been
completed successfully but auto clock set
has not, "1" (channel position) will be
displayed after the OK button is pressed in
step 6 on page 5.
pg. 51) have also been stored in the recorder's memory, the station name will be displayed at
pg. 51) have also been stored in the recorder's memory, the station name will be displayed at
Timer Programming").
SVERIGE
DANMARK
ÖSTERREICH
ITALIA
INITIAL SETTINGS (cont.)
"Delete A Channel" on page 49.
[ SVENSKA ESPAÑA
[ DANSK NEDERLAND [ NEDERLANDS
[ DEUTSCH GREECE
[ ITALIANO OTHERS
"Language" on page 7.
C
When neither auto channel set nor auto
clock set has been completed success-
fully, "– –:– –" will be displayed.
V Timer Programming
HOW IEW
V , be sure to
HOW IEW
pg. 45, "Video Channel Set".
[ CASTELLANO
[ ENGLISH
[ ENGLISH
V ,
HOW IEW