Custom Settings (Custom Setup); Settings For The Sound (Audio Setup); Ao Y; Additional Information - Sony DVP-NS38 Service Manual

DVP-NS28/NS38/NS39/NS47P/NS57P/NS64P/NS67P
QQ
3 7 63 1515 0
Custom Settings
(CUSTOM
SETUP)
Use this to set up playback related and other
settings.
Select "CUSTOM SETUP" in the Setup
Display. To use the display, see "Using the
Setup Display" (page 59).
The default settings are underlined.
CUSTOM SETUP
AUTO POWER OFF:
AUTO PLAY:
DIMMER:
PAUSE MODE:
TRACK SELECTION:
MULTI-DISC RESUME:
DivX: Registration Code
◆ AUTO POWER OFF
Switches the Auto Power Off setting on or off.
OFF
Switches this function off.
ON The player enters standby mode
when left in stop mode for more
than 30 minutes.
◆ AUTO PLAY
Switches the Auto Play setting on or off. This
function is useful when the player is
connected to a timer (not supplied).
OFF Switches this function off.
ON Automatically starts playback
when the player is turned on by
a timer (not supplied).
◆ DIMMER
Adjusts the lighting of the front panel display.
BRIGHT
Makes the lighting bright.
DARK Makes the lighting dark.
◆ PAUSE MODE (DVDs only)
Selects the picture in pause mode.
AUTO The picture, including subjects
that move dynamically, is
output with no jitter. Normally
select this position.
TE
L 13942296513
FRAME The picture, including subjects
that do not move dynamically,
is output in high resolution.
◆ DTS
Selects whether or not to output DTS signals.
OFF
Select this when the player is
connected to an audio
component without a built-in
DTS decoder.
ON Select this when the player is
connected to an audio
component with a built-in DTS
decoder.
◆ 48kHz/96kHz PCM (DVD VIDEO only)
Selects the sampling frequency of the audio
signal.
48kHz/16bit The audio signals of DVD
VIDEOs are always converted
to 48kHz/16bit.
96kHz/24bit All types of signals including
96kHz/24bit are output in their
original format. However, if the
signal is encrypted for
copyright protection purposes,
the signal is only output as
48kHz/16bit.
Note
The analog audio signals from the LINE OUT L/R
(AUDIO) jacks are not affected by this setting and
keep their original sampling frequency level.
www
http://www.xiaoyu163.com
◆ TRACK SELECTION (DVD VIDEO only)
Gives the sound track which contains the
highest number of channels priority when you
play a DVD VIDEO on which multiple audio
formats (PCM, DTS, or Dolby Digital
format) are recorded.
OFF No priority given.
AUTO Priority given.
Notes
• When you set the item to "AUTO," the language
may change. The "TRACK SELECTION" setting
OFF
has higher priority than the "AUDIO" settings in
OFF
BRIGHT
"LANGUAGE SETUP" (page 60).
AUTO
• If you set "DTS" to "OFF" (page 65), the DTS
OFF
ON
sound track is not played even if you set "TRACK
SELECTION" to "AUTO."
• If PCM, DTS, and Dolby Digital sound tracks
have the same number of channels, the player
selects PCM, DTS, and Dolby Digital sound
tracks in this order.
◆ MULTI-DISC RESUME (DVD VIDEO/
VIDEO CD only)
Switches the Multi-disc Resume setting on or
off. Resume playback can be stored in
memory for up to 6 different DVD VIDEOs/
VIDEO CDs (page 23).
ON Stores the resume setting in
memory for up to six discs.
OFF Does not store the resume
setting in memory. Playback
restarts at the resume point only
for the current disc in the player.
Note
If you run Quick Setup, Multi-disc Resume setting
stored in memory may return to the default settings.
◆ DivX
Displays the registration code for this player.
For more information, go to
http://www.divx.com/vod
on the Internet.
x ao
y
. i
8
Settings for the Sound
(AUDIO SETUP)
"AUDIO SETUP" allows you to set the sound
according to the playback and connection
conditions.
Select "AUDIO SETUP" in the Setup
Display. To use the display, see "Using the
Setup Display" (page 59).
The default settings are underlined.
AUDIO SETUP
AUDIO DRC:
DOWNMIX:
DIGITAL OUT:
DOLBY DIGITAL:
DTS:
48kHz/96kHz PCM:
◆ AUDIO DRC (Dynamic Range Control)
(DVDs only)
Makes the sound clear when the volume is
turned down when playing a DVD that
conforms to "AUDIO DRC."
This function affects the output from the
following jacks:
– LINE OUT L/R (AUDIO) jacks
– DIGITAL OUT (COAXIAL) jack only
when "DOLBY DIGITAL" is set to "D-
PCM" (page 64).
STANDARD Normally, select this position.
TV MODE Makes low sounds clear even if
you turn the volume down.
WIDE Gives you the feeling of being
RANGE at a live performance.
◆ DOWNMIX (DVDs only)
Switches the method for mixing down to 2
channels when you play a DVD which has
rear sound elements (channels) or is recorded
in Dolby Digital format. For details on the
rear signal components, see "Checking the
audio signal format" (page 39). This function
affects the output of the following jacks:
– LINE OUT L/R (AUDIO) jacks
– DIGITAL OUT (COAXIAL) jack when
Q Q
"DOLBY DIGITAL" is set to "D-PCM"
3 6 7 1 3
(page 64).
63 64

Additional Information

Troubleshooting

If you experience any of the following
difficulties while using the player, use this
troubleshooting guide to help remedy the
problem before requesting repairs. Should
any problem persist, consult your nearest
Sony dealer.
Power
The power is not turned on.
, Check that the power cord is connected
securely.
Picture
There is no picture/picture noise appears.
, Re-connect the connecting cord securely.
, The connecting cords are damaged.
, Check the connection to your TV (page 15)
and switch the input selector on your TV so
that the signal from the player appears on
the TV screen.
, The disc is dirty or flawed.
, If the picture output from your player goes
through your VCR to get to your TV or if
you are connected to a combination TV/
VIDEO player, the copy-protection signal
applied to some DVD programs could affect
picture quality.
, You set the "PROGRESSIVE
(COMPONENT OUT)" in "SCREEN
SETUP" to "ON" even though your TV
cannot accept the progressive signal. In this
case, refer to page 62 to reset the setting.
, Even if your TV is compatible with
progressive format 480p signals and
connected using COMPONENT VIDEO
OUT jacks, the image may be affected when
you set the player to progressive format. In
this case, set "PROGRESSIVE
u163
(COMPONENT OUT)" in "SCREEN
SETUP" to "OFF" so that the player is set to
normal (interlace) format (page 62).
.
65 66
1-16
2 9 9 4 2 8
DOLBY
Normally, select this position.
SUR- Multi-channel audio signals are
ROUND output to 2 channels for enjoying
surround sounds.
NORMAL Multi-channel audio signals are
downmixed to 2 channels for use
with your stereo.
◆ DIGITAL OUT
Selects if audio signals are output via the
DIGITAL OUT (COAXIAL) jack.
ON Normally, select this position.
When you select "ON," see
"Setting the digital output signal"
STANDARD
for further settings.
DOLBY SURROUND
ON
D-PCM OFF The influence of the digital circuit
OFF
upon the analog circuit is
48kHz/16bit
minimal.
Setting the digital output signal
Switches the method of outputting audio
signals when you connect a component such
as an amplifier (receiver) or MD deck with a
digital input jack.
For connection details, see page 17.
Select "DOLBY DIGITAL," "DTS," and
"48kHz/96kHz PCM" after setting
"DIGITAL OUT" to "ON."
If you connect a component that is
incompatible with the selected audio signal, a
loud noise (or no sound) may be heard from
the speakers, risking damage to your ears or
speakers.
◆ DOLBY DIGITAL (DVDs only)
Selects the type of Dolby Digital signal.
D-PCM Select this when the player is
connected to an audio
component without a built-in
Dolby Digital decoder. You can
select whether the signals
conform to Dolby Surround
(Pro Logic) or not by making
adjustments to the
"DOWNMIX" item in
"AUDIO SETUP" (page 64).
DOLBY Select this when the player is
DIGITAL connected to an audio
1 5 0 5 8 2 9 9 4
component with a built-in
Dolby Digital decoder.
The picture does not fill the screen, even
though the aspect ratio is set in "TV TYPE"
under "SCREEN SETUP."
, The aspect ratio of the disc is fixed on your
DVD.
Sound
There is no sound.
, Re-connect the connecting cord securely.
, The connecting cord is damaged.
, The player is connected to the wrong input
jack on the amplifier (receiver) (page 17).
, The amplifier (receiver) input is not
correctly set.
, The player is in pause mode or in Slow-
motion Play mode.
, The player is in fast forward or fast reverse
mode.
, If the audio signal does not come through
the DIGITAL OUT (COAXIAL) jack,
check the audio settings (page 64).
, While playing a Super VCD on which the
audio track 2 is not recorded, no sound will
come out when you select "2:STEREO,"
"2:1/L," or "2:2/R."
The sound volume is low.
, The sound volume is low on some DVDs.
The sound volume may improve if you set
"AUDIO DRC" in "AUDIO SETUP" to
"TV MODE" (page 64).
Operation
The remote does not function.
, The batteries in the remote are weak.
, There are obstacles between the remote and
the player.
, The distance between the remote and the
player is too far.
, The remote is not pointed at the remote
m
sensor on the player.
The disc does not play.
, The disc is turned over.
co
Insert the disc with the playback side facing
down.
, The disc is skewed.
, The player cannot play certain discs
(page 6).
, The region code on the DVD does not match
the player.
, Moisture has condensed inside the player
(page 3).
9 9
2 8 9 9