Panasonic Lumix DMC-FZ50PP Service Manual page 45

Service Manual
Diagrams and Replacement
Parts List
Digital Camera
DMC-FZ50PP DMC-FZ50GC
DMC-FZ50PL DMC-FZ50GD
DMC-FZ50EB DMC-FZ50GK
DMC-FZ50EE DMC-FZ50GN
DMC-FZ50EF DMC-FZ50GT
DMC-FZ50EG DMC-FZ50SG
DMC-FZ50EGM
Vol. 1
Colour
(S)...........Silver Type
(K)...........Black Type
Table of contents
S1. About Indication of The Schematic Diagram ............................ S-1
S1.1. Important Safety Notice......................................................... S-1
S2. Voltage Chart ........................................................................... S-2
S2.1. Flash P.C.B. .......................................................................... S-2
S3. Block Diagram .......................................................................... S-3
S3.1. Overall Block Diagram .......................................................... S-3
S4. Schematic Diagram .................................................................. S-4
S4.1. Interconnection Diagram ....................................................... S-4
S4.2. Flash Schematic Diagram ..................................................... S-5
S4.3. AF Assist Schematic Diagram ............................................... S-5
S4.4. LCD IF Schematic Diagram .................................................. S-6
S4.5. CCD Flex Schematic Diagram .............................................. S-6
S4.6. MIC Flex Schematic Diagram ............................................... S-7
S4.7. Lens Flex Schematic Diagram .............................................. S-8
DSC0607019CE
S1. About Indication of The Schematic Diagram
S1.1. Important Safety Notice
COMPONENTS IDENTIFIED WITH THE MARK
FOR SAFETY. WHEN REPLACING ANY OF THESE COMPONENTS USE ONLY THE SAME TYPE.
1.Although reference number of the parts is indicated on the P.C.B. drawing and/or
schematic diagrams, it is NOT mounted on the P.C.B. when it is displayed with "$" mark.
2.It is only the "Test Round" and no terminal (Pin) is available on the P.C.B.
when the TP (Test Point) indicated as "
3.The voltage being indicated on the schematic diagram is measured in
"Standard-Playback" mode when there is no specify mode is mentioned.
4.Although the voltage and waveform available on here is measured with standard frame,
it may be differ from actual measurement due to modification of circuit and so on.
5.The voltage being indicated here may be include observational-error (deviation) due to
internal-resistance and/or reactance of equipment. Therefore, handle the value
indicated on here as reference.
6.Use the parts number indicated on the Replacement Parts List .
7.Indication on Schematic diagrams:
S5. Print Circuit Board .................................................................... S-9
S5.1. Flash P.C.B. .......................................................................... S-9
S5.2. AF Assist P.C.B. .................................................................... S-9
S5.3. LCD IF P.C.B. ...................................................................... S-10
S5.4. CCD Flex P.C.B. .................................................................. S-11
S5.5. MIC Flex P.C.B. ................................................................... S-12
S5.6. Lens Flex P.C.B. .................................................................. S-13
S6. Replacement Parts List .......................................................... S-15
S7. Exploded View ....................................................................... S-22
S7.1. Frame and Casing Section (1) ............................................ S-22
S7.2. Frame and Casing Section (2) ............................................ S-23
S7.3. Frame and Casing Section (3) ............................................ S-24
S7.4. Packing Parts and Accessories Section .............................. S-25
S-1
" mark.
Circuit name being connected.
This signal is connected
OFTR FEP
to the FEP schematic diagram.
Name of Signal
HAVE THE SPECIAL CHARACTERISTICS