TABLE OF CONTENTS PAGE PAGE 1 Safety Precaution -------------------------------------------------3 1.1. General Guidelines ----------------------------------------3 1.2. Leakage Current Cold Check ---------------------------3 1.3. Leakage Current Hot Check (See Figure 1.)--------3 1.4. How to Discharge the Capacitor on Flash PCB------------------------------------------------------------4 2 Warning --------------------------------------------------------------5 2.1. Prevention of Electro Static Discharge (ESD) to ElectrostaticallySensitive (ES) Devices -----------5 2.2.
1 Safety Precaution 1.1. General Guidelines 1.3. Leakage Current Hot Check 1. IMPORTANT SAFETY NOTICE (See Figure 1.) There are special components used in this equipment 1. Plug the AC cord directly into the AC outlet. Do not use which are important for safety. These parts are marked by an isolation transformer for this check.
1.4. How to Discharge the Capacitor on Flash PCB CAUTION: 1. Be sure to discharge the capacitor on FLASH PCB. 2. Be careful of the high voltage circuit on FLASH PCB when servicing. [Discharging Procedure] 1. Refer to the disassemble procedure and Remove the necessary parts/unit. 2.
2 Warning 2.1. Prevention of Electro Static Discharge (ESD) to Electrostatically Sensitive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec- trostatically Sensitive (ES) Devices. The following techniques should be used to help reduce the incidence of component damage caused by electro static discharge (ESD).
2.3.2.3. How to Replace the Fuse A replacement fuse cover can be purchased from your local Panasonic Dealer. 1. Remove the Fuse Cover with a screwdriver. If the fitted moulded plug is unsuitable for the socket outlet in your home then the fuse should be removed and the plug cut off and disposed of safety.
2.4. How to Replace the Lithium Battery 2.4.1. Replacement Procedure 1. Remove the MAIN PCB. (Refer to Disassembly Procedures.) 2. Remove the Lithium battery (Ref. No. “Z9101” at component side of MAIN PCB) and then replace it into new one. NOTE: This Lithium battery is a critical component.
Page 8
NOTE: Above caution is applicable for a battery pack which is for DMC-FZ50 series, as well.
3 Service Navigation 3.1. Introduction This service manual contains technical information, which allow service personnel’s to understand and service this model. Please place orders using the parts list and not the drawing reference numbers. If the circuit is changed or modified, the information will be followed by service manual to be controlled with original service manual. 3.2.
3.4. How to Define the Model Suffix (NTSC or PAL model) There are seven kinds of DMC-FZ50, regardless of the colours. • a) DMC-FZ50S • b) DMC-FZ50PP • c) DMC-FZ50EB/EF/EG/EGM/GN • d) DMC-FZ50EE • e) DMC-FZ50GD • f) DMC-FZ50GT • g) DMC-FZ50PL/GC/GK/SG (DMC-FZ50S is exclusively Japan domestic model.) What is the difference is that the “INITIAL SETTING”...
3.4.2. INITIAL SETTINGS: When you replace the Main PCB be sure to perform the initial settings after achieving the Adjustment, by ordering the following pro- cedure in accordance with model suffix. • Step 1. The temporary cancellation of factory setting: Set the mode dial to “[ P ]”.
6 Service Mode 6.1. Error Code Memory Function 1. General description This unit is equipped with history of error code memory function, and can be memorized 32 error codes in sequence from the latest. When the error is occurred more than 32, oldest error is overwritten in sequence. The error code is not memorized when the power supply is shut down forcibly (when the unit is powered on by the battery, the battery is pulled out) because the error code is memorized to FLASH ROM when the unit is powered off.
Page 15
Attribute Main item Sub item Error code Contents (Upper) High 4 bits Low 4 bits Check point (Lower) LENS Lens drive 1800 1000 PSD (X) error. Hall element (X axis) position detect error in OIS unit. OIS Unit 2000 PSD (Y) error. Hall element (Y axis) position detect error in OIS unit. OIS Unit 3000 GYRO (X) error.
Page 16
Attribute Main item Sub item Error code Contents (Upper) High 4 bits Low 4 bits Check point (Lower) SOFT Reset 3000 0001 NMI reset Non Mask-able Interrupt 0007 (30000001-30000007 are caused by factors) Card Card 3100 0001 Card logic error SD card data line or IC6001 (VENUS 3) 0002 Card physical error...
6.2. Confirmation of Firmware Version The Firmware version can be confirmed by ordering the following steps:. • Step 1. The temporary cancellation of factory setting: Set the mode dial to “[ P ]”. Insert the SD memory card which has a few photo data. When keep pressing [ Optical Image Stabilizer ] and “[ UP ] of Cross key”...
7.2. When Replacing the Main PCB After replacing the MAIN PCB, be sure to achieve adjustment. The adjustment instruction is available at “software download” on the “Support Information from NWBG-PAVC” web-site in “TSN system”, together with Maintenance software. 7.3. Service Position This Service Position is used for checking and replacing parts.
Page 20
CAUTION-1. (When servicing FLASH PCB) 1. Be sure to discharge the capacitor on FLASH PCB. Refer to “HOW TO DISCHARGE THE CAPACITOR ON FLASH PCB”. The capacitor voltage is not lowered soon even if the AC Cord is unplugged or the battery is removed. 2.
Page 23
8.3.1. Removal of the Rear Cover Unit Fig. D2 8.3.2. Removal of the Top Case Unit Fig. D3 Fig. D1...
Page 24
8.3.3. Removal of the LCD Case Unit Fig. D4 Fig. D5...
Page 25
8.3.4. Removal of the SD Door Unit, Rear 8.3.5. Removal of the Main PCB Operation Plate, Speaker, CROSS Key Button, Rear Operation Button Fig. D7 Fig. D6...
Page 26
8.3.6. Removal of the Battery Case and 8.3.8. Removal of the Side Operation Unit Flash PCB Unit Fig. D10 8.3.9. Removal of the Tripod Plate Unit and Jack Door Unit Fig. D8 8.3.7. Removal of the Lens Unit Fig. D9 Fig.
Page 27
8.3.10. Removal of the Flash PCB Unit and 8.3.11. Removal of the Battery Cover Unit Battery Catcher Unit and Catcher Spring Fig. D13 8.3.12. Removal of the Battery Lock Knob Fig. D12 Fig. D14...
Page 28
8.3.13. Removal of the Flash PCB 8.3.14. Removal of the LCD Unit Fig. D15 Fig. D16...
Page 29
8.3.16. Removal of the Top Operation Unit Fig. D17 8.3.15. Removal of the EVF Unit Fig. D18 Fig. D19...
Page 30
8.3.17. Removal of the Mic FPC PCB 8.3.18. Removal of the Flash Unit Fig. D21 Fig. D20...
Page 31
8.3.19. Removal of the Hot Shoe Unit Fig. D23 NOTE: (When Assembling) Be sure to confirm the following points when assembling. • The Screw is tightened enough. • Assembling conditions are fine. (No distortion, no illegal- space.) • No dust and/or dirt on every Lens surfaces. •...
8.4. Disassembly Procedure for the 8.4.2. Removal of the Decoration Ring Lens NOTE: When Disassembling and Assembling for the Lens 1. To minimize the possibility of the CCD being dirt, perform disassemble and/or assemble under the condition of the CCD is being mounted. Disassembling procedures for the CCD unit, refer to item 8.6.
Page 33
8.4.4. Removal of the Master Flange Unit, 8.4.5. Removal of the Zoom Encoder Unit 1st Lens Frame Cushion and Lens Ring Base 8.4.6. Removal of the Focus Motor Unit...
Page 34
8.4.7. Removal of the Master Flange 8.4.9. Removal of the Inside Frame 8.4.8. Removal of the 5th Lens Frame Unit and F Guide Pole L/S...
Page 35
8.4.10. Removal of the 4th Lens Frame Unit 8.4.12. Removal of the 2nd Lens Frame Unit 8.4.13. Removal of the Cam Frame Unit and Guide Pole 8.4.11. Removal of the 3rd Lens Frame Unit...
8.4.14. Removal of the 1st Lens Frame Unit 8.5. Assembly Procedure for the Lens 8.5.1. Assembly for the 1st Lens Frame Unit...
Page 37
8.5.2. Assembly for the Guide Pole and 8.5.3. Assembly for the 2nd Lens Frame Cam Frame Unit Unit 8.5.4. Assembly for the 3rd Lens Frame Unit...
Page 38
8.5.5. Assembly for the 4th Lens Frame 8.5.6. Assembly for the Inside Frame Unit and Thrust Ring...
Page 39
8.5.7. Assembly for the 5th Lens Frame 8.5.9. Assembly for the Focus Motor Unit Unit and F Guide Pole L/S 8.5.8. Assembly for the Master Frange...
Page 40
8.5.10. Assembly for the Zoom Encoder 8.5.11. Assembly for the Lens Ring Base Unit Master Frange Unit and 1st Lens Frame Cushion...
Page 41
8.5.12. Assembly for the Lens Ring Front 8.5.13. Assembly for the Decoration Ring and Zoom Ring Unit 8.5.14. Assembly for the Lens FPC Unit...
9 Measurements and Adjustments 9.1. Adjustment Procedures The relation between Replaced part and Necessary Adjustment is shown in the following table. When concerned part is replaced, be sure to achieve the necessary adjustment(s). As for Adjustment condition/procedure, consult the “Adjustment Manual” which is available in Adjustment software. The Adjustment software is available at “TSN Website”, therefore, access to “TSN Website”...
10 Maintenace 10.1. Cleaning Lens, Viewfinder and LCD Panel Do not touch the surface of lens, Viewfinder and LCD Panel with your hand. When cleaning the lens, use air-Blower to blow off the dust. When cleaning the LCD Panel, dampen the lens cleaning paper with lens cleaner, and the gently wipe the their surface. Note: A lens cleaning paper and lens cleaner are available at local camera shops and market place.
Page 45
DSC0607019CE S1. About Indication of The Schematic Diagram Service Manual S1.1. Important Safety Notice COMPONENTS IDENTIFIED WITH THE MARK HAVE THE SPECIAL CHARACTERISTICS FOR SAFETY. WHEN REPLACING ANY OF THESE COMPONENTS USE ONLY THE SAME TYPE. Diagrams and Replacement 1.Although reference number of the parts is indicated on the P.C.B. drawing and/or Parts List schematic diagrams, it is NOT mounted on the P.C.B.
S2. Voltage Chart Note) Indicated voltage values are the standard values for the unit measured by the DC electronic circuit tester (high-impedance) with the chassis taken as standard. Therefore, there may exist some errors in the voltage values, depending on the internal impedance of the DC circuit tester. S2.1.
S4. Schematic Diagram S4.1. Interconnection Diagram FLASH P.C.B. P9002 TRG IN (FOIL SIDE) UNREG GND TOP OPERATION UNIT FLASH UNIT (COMPONENT SIDE) FP8101 P9001 LAMP+ LAMP- MICROPHONE SIDE OPERATION UNIT AF ASSIST LED P.C.B. EVF UNIT FLASH SW UNIT BATTERY TP9501 TP9502 SHOE...
S4.7. Lens Flex Schematic Diagram POSITIVE VOLTAGE LINE DC SOLENOID (SHUTTER) SHUTTER UNIT COIL STEPPING MOTOR (IRIS) COIL Y DRV- Y DRV+ DRIVE COIL ( Y ) X DRV- X DRV+ DRIVE COIL ( X ) Y VO- Y VH- OIS UNIT HALL SENSOR ( Y ) Y VO+...
S6. Replacement Parts List Note: 1.* Be sure to make your orders of replacement parts according to this list. 2. IMPORTANT SAFETY NOTICE Components identified with the mark have the special characteristics for safety. When replacing any of these components, use only the same type. 3.
Page 60
DMC-FZ50EB-K/S,EF-K/S,EGMK/S,EG-K/S,PL-K/S,PP-K/S,EE-K/S,GC-K/S,GD-K/S,GN-K/S,GK-K/S,GT-K/S,SG-K/S Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks ------ P.C.B. LIST ------ VEP58028A FLASH P.C.B. 1 (RTL) E.S.D. VEP59016A AF ASSIST LED P.C.B. 1 (RTL) E.S.D. VEP54005A LCD IF P.C.B. 1 (RTL) VEK0K43 CCD UNIT 1 [PAVC-CSG] E.S.D.
Page 61
DMC-FZ50EB-K/S,EF-K/S,EGMK/S,EG-K/S,PL-K/S,PP-K/S,EE-K/S,GC-K/S,GD-K/S,GN-K/S,GK-K/S,GT-K/S,SG-K/S Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks VEP58028A FLASH P.C.B. (RTL) E.S.D. C8101 F1K2E223A004 C.CAPACITOR 250V 0.022U C8103 F1K2J102A010 C.CAPACITOR 630V 1000P C8105 ECJ1VB0J105K C.CAPACITOR CH 6.3V 1U C8106 F1J1A106A023 C.CAPACITOR CH 10V 10U C8107 F1K2E223A004 C.CAPACITOR 250V 0.022U...
Page 62
DMC-FZ50EB-K/S,EF-K/S,EGMK/S,EG-K/S,PL-K/S,PP-K/S,EE-K/S,GC-K/S,GD-K/S,GN-K/S,GK-K/S,GT-K/S,SG-K/S Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks VEK0K43 CCD UNIT [PAVC-CSG] E.S.D. C3101 ECJ1VB1C105K C.CAPACITOR CH 16V 1 [PAVC-CSG] C3102 F1J1A106A023 C.CAPACITOR CH 10V 10U 1 [PAVC-CSG] C3103 ECJ0EB1A104K C.CAPACITOR CH 10V 0.1U 1 [PAVC-CSG] Q3101 2SC4627JCL...
Page 63
DMC-FZ50EB-K/S,EF-K/S,EGMK/S,EG-K/S,PL-K/S,PP-K/S,EE-K/S,GC-K/S,GD-K/S,GN-K/S,GK-K/S,GT-K/S,SG-K/S Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks XQN16+BJ5FN SCREW VYK1W37 FRONT CASE UNIT 1 (SILVER) XQN16+BJ5FN SCREW VYK1W36 FRONT CASE UNIT 1 (BLACK) XQN16+BJ5FN SCREW VXA8322 TRIPOD PLATE UNIT 1 [PAVC-CSG] XQN16+BJ5FN SCREW VYF3043 BATTERY COVER UNIT...
Page 64
DMC-FZ50EB-K/S,EF-K/S,EGMK/S,EG-K/S,PL-K/S,PP-K/S,EE-K/S,GC-K/S,GD-K/S,GN-K/S,GK-K/S,GT-K/S,SG-K/S Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks VYK1Z21 REAR CASE UNIT 1 [PAVC-CSG](SILVER) N9ZZ00000308 SIDE OPERATION UNIT 1 (SILVER) VYK1Z20 REAR CASE UNIT 1 [PAVC-CSG](BLACK) N9ZZ00000309 SIDE OPERATION UNIT 1 (BLACK) VGQ8952 EVF COVER CUSHION 1 [PAVC-CSG]...
Page 65
DMC-FZ50EB-K/S,EF-K/S,EGMK/S,EG-K/S,PL-K/S,PP-K/S,EE-K/S,GC-K/S,GD-K/S,GN-K/S,GK-K/S,GT-K/S,SG-K/S Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks VQT0W42 O/I PC CONNECTOR 1 [PAVC-CSG] ------------ BATTERY (ENGLISH/SPANISH/ DE-994AB AC ADAPTOR 1 EB,EF,EGM,EG,GN PORTUGUESE) DE-993BB AC ADAPTOR 1 PL,PP VQT0W41 O/I PC CONNECTOR 1 [PAVC-CSG] DE-994BA AC ADAPTOR...