Table of Contents
Advertisement
Quick Links
The following are general installation instructions. Actual
installation may vary depending on the ATV manufacturer
and model.
Warnings
1. T
R
HE
AMSEY
DESIGNED FOR USE ON SELF
NOT DESIGNED FOR AND SHOULD NOT BE USED ON WINCHES OR HOISTS IN
INDUSTRIAL APPLICATIONS
.)
ETC
OR FOR ANY OTHER REMOTE CONTROLLED APPLICATION
2. W
HEN REELING IN CABLE UNDER NO LOAD
WHEN THE HOOK IS A MINIMUM OF
. C
LEAD
AREFULLY JOG THE REMOTE CONTROL BUTTON UNTIL THE HOOK IS A
MINIMUM OF
AND FINISH SPOOLING IN CABLE BY ROTATING THE DRUM BY HAND
3. When finished winching, turn transmitter off.
4. Do not pressure wash or steam clean the receiver. This can dam-
age the receiver and adversely affect operation.
5. Refer to winch owner's manual for all winch operating instruc-
tions and warnings.
UNIVERSAL WIRELESS REMOTE
U
W
NIVERSAL
IRELESS
-
RECOVERY WINCHES ONLY
(
CAR HAULERS
1
(.3
)
FT
M
FROM THE FAIR
INSTALLATION AND OPERATING
INSTRUCTIONS FOR RAMSEY
CONTROL FOR ATV WINCHES
KIT #'S 251203, 251204,
R
EMOTE FOR
/
CARRIERS
,
RELEASE THE REMOTE BUTTON
3
(1
)
FT
M
-
LEAD
251205, & 251206
ATV W
INCHES IS
. T
HE REMOTE IS
,
,
WRECKERS
.
FROM THE WINCH FAIR
. D
ISENGAGE THE CLUTCH
,
CRANES
-
.
Advertisement
Table of Contents
Related Manuals for Ramsey Electronics 251203
Summary of Contents for Ramsey Electronics 251203
- Page 1 INSTALLATION AND OPERATING INSTRUCTIONS FOR RAMSEY UNIVERSAL WIRELESS REMOTE CONTROL FOR ATV WINCHES KIT #’S 251203, 251204, 251205, & 251206 The following are general installation instructions. Actual installation may vary depending on the ATV manufacturer and model. Warnings 1. T...
-
Page 2: Table Of Contents
251203 SUPERWINCH ATV 2000 & T 1500 Parts List ............1 Before Beginning Installation ......2 Installing the Kit ..........2-4 Electrical Schematic ........5 Testing & Operation of Remote ......6 Troubleshooting Guide........21 251204 WARN A2000, SUPERWINCH X1, X2, X1F, X2F, EX1 Parts List ............7 Before Beginning Installation ...... -
Page 3: 251203 Superwinch Atv 2000 & T 1500
251203 SUPERWINCH ATV 2000 & T 1500 ITEM QTY. PART DESCRIPTION 282058 WIRELESS RECEIVER & TRANSMITTER KIT 251198 DIPOLE ANTENNA KIT 251234 SOLENOID KIT 251190 REPLACEMENT TRANSMITTER REPLACEMENT BATTERY 416227 SCREW #10-24 X 3/4 TRUSS F/B NUT #10-24 HEX LOCK... -
Page 4: Before Beginning Installation
251203 SUPERWINCH ATV 2000 & T 1500 Before Beginning Installation 1. Disconnect power lead from winch to battery. 2. Disengage winch clutch. 3. Remove hood or cowling as necessary for easier access to installation area. 4. Locate & mark mounting locations for receiver, toggle switch, solenoid assembly, &... - Page 5 251203 SUPERWINCH ATV 2000 & T 1500 Connecting Wiring to Solenoids NOTE: For clarification see wiring schematic on page 5. 1. Attach black with yellow stripe motor lead to lower right terminal stud “B” on solenoid. 2. Attach black motor lead to lower left terminal stud “C” on solenoid.
- Page 6 251203 SUPERWINCH ATV 2000 & T 1500 Wiring the Toggle Switch NOTE: For clarification see wiring schematic on page 5. 1. Connect red wire to center spade. 2. Connect green wire to the toggle switch terminal in the “OUT” position.
-
Page 7: Electrical Schematic
251203 SUPERWINCH ATV 2000 & T 1500 Electrical Schematic TRANSMITTER WIRELESS COPPER TAPE SIGNAL ANTENNA LEFT CONTACT TOGGLE SWITCH RIGHT CONTACT GREEN WIRE RECEIVER COAX CABLE Programing instructions: Press and hold membrane below, press ON/OFF button on transmitter for 3 seconds , press OUT button for 3 seconds or until winch activation . -
Page 8: Testing & Operation Of Remote
251203 SUPERWINCH ATV 2000 & T 1500 Testing/Operation ON/OFF 1. Reconnect the positive power lead from solenoid to battery. 2. Pull approximately 20 ft of cable off the winch by hand. Transmitter 3. Re-engage the winch clutch. 4. Test the remote transmitter. The transmitter has push buttons labeled accord- ing to their function. -
Page 9: Parts List
251204 WARN A2000 / SUPERWINCH X1, X2, X1F, X2F, EX1 ITEM QTY. PART DESCRIPTION 282058 WIRELESS RECEIVER & TRANSMITTER KIT 251198 DIPOLE ANTENNA KIT 251234 SOLENOID KIT 251190 REPLACEMENT TRANSMITTER REPLACEMENT BATTERY 416227 SCREW #10-24 X 3/4 TRUSS F/B NUT #10-24 HEX LOCK NUT #10-24 HEX Z/P 418140 FLAT WASHER #10 Z/P... -
Page 10: 251204 Warn A2000, Superwinch X1, X2, X1F, X2F, Ex1
251204 WARN A2000 / SUPERWINCH X1, X2, X1F, X2F, EX1 Before Beginning Installation 1. Disconnect power lead from winch to battery. 2. Disengage winch clutch. 3. Remove hood or cowling as necessary for easier access to instal- lation area. 4. Locate & mark mounting locations for receiver, toggle switch, sole- noid assembly, &... - Page 11 251204 WARN A2000 / SUPERWINCH X1, X2, X1F, X2F, EX1 Connecting Wiring to Solenoids NOTE: For clarification see wiring schematic on page 11. 1. Attach black with yellow stripe motor lead to lower right terminal stud “B” on solenoid. 2. Attach black motor lead to lower left terminal stud “C” on solenoid. 3.
- Page 12 251204 WARN A2000 / SUPERWINCH X1, X2, X1F, X2F, EX1 Wiring the Toggle Switch NOTE: For clarification see wiring schematic on page 11. 1. Connect red wire to center spade. 2. Connect green wire to the toggle switch terminal in the “OUT” position.
-
Page 13: Electrical Schematic
251204 WARN A2000 / SUPERWINCH X1, X2, X1F, X2F, EX1 Electrical Schematic WIRELESS COPPER TAPE TRANSMITTER SIGNAL ANTENNA LEFT CONTACT TOGGLE SWITCH RIGHT CONTACT GREEN WIRE RECEIVER COAX CABLE Programing instructions: Press and hold membrane below, press ON/OFF button on transmitter for 3 seconds , press OUT button for 3 seconds or until winch activation . -
Page 14: Testing & Operation Of Remote
251204 WARN A2000 / SUPERWINCH X1, X2, X1F, X2F, EX1 Testing/Operation ON/OFF 1. Reconnect the positive power lead from solenoid to battery. 2. Pull approximately 20 ft of cable off the winch by hand. Transmitter 3. Re-engage the winch clutch. 4. -
Page 15: 251205 Warn A2500
251205 WARN A2500 ITEM QTY. PART DESCRIPTION 282058 WIRELESS RECEIVER & TRANSMITTER KIT 251198 DIPOLE ANTENNA KIT 251190 REPLACEMENT TRANSMITTER REPLACEMENT BATTERY 440125 WIRE SPLICE 440274 CABLE TIES 289189 WARN ADAPTER CABLE ADAPTER CABLE STORAGE CLIP WIRING HARNESS (NOT USED) * SONY CR2032 OR DURACELL DL2032 WIRE SPLICE ANTENNA... -
Page 16: Before Beginning Installation
251205 WARN A2500 Before Beginning Installation 1. Disconnect power lead from solenoid to battery. 2. Disengage winch clutch. 3. Remove hood or cowling as necessary for easier access to installation area. 4. Locate & mark mounting locations for receiver, & antenna. NOTE: Make sure locations are close enough for wiring connec- tions to be made without making alterations to wire... -
Page 17: Electrical Schematic
251205 WARN A2500 Installing the Antenna NOTE: For clarification see wiring schematic below. 1. Clean predetermined mounting surface with Isopropyl alcohol and buff dry. (In ATVs without hoods the best place to mount the antenna will be the underside of the ATV cowling in the highest possible position.) 2. -
Page 18: Testing & Operation Of Remote
251205 WARN A2500 Testing/Operation 1. Reconnect the positive power lead from solenoid to battery. 2. Pull approximately 20 ft of cable off the ON/OFF winch by hand. 3. Re-engage the winch clutch. 4. Test the remote transmitter. The trans- mitter has push buttons labeled accord- Transmitter ing to their function. -
Page 19: Parts List
251206 SUPERWINCH X1, X2, X1F, X2F, EX1 (WITH HAND HELD REMOTE) ITEM QTY. PART DESCRIPTION 282058 WIRELESS RECEIVER & TRANSMITTER KIT 251198 DIPOLE ANTENNA KIT 251190 REPLACEMENT TRANSMITTER REPLACEMENT BATTERY 440125 WIRE SPLICE 440274 CABLE TIES 289190 SUPERWINCH ADAPTER CABLE CABLE STORAGE CLIP WIRING HARNESS (NOT USED) * SONY CR2032 OR DURACELL DL2032... -
Page 20: 251206 Superwinch X1, X2, X1F, X2F, Ex1
251206 SUPERWINCH X1, X2, X1F, XF2 EX1 (W/ HAND HELD REMOTE) Before Beginning Installation 1. Disconnect power lead from solenoid to battery. 2. Disengage winch clutch. 3. Remove hood or cowling as necessary for easier access to installa- tion area. 4. -
Page 21: Electrical Schematic
251206 SUPERWINCH X1, X2, X1F, XF2 EX1 (W/ HAND HELD REMOTE) Installing the Antenna NOTE: For clarification see wiring schematic below. 1. Clean predetermined mounting surface with Isopropyl alcohol and buff dry. (In ATVs without hoods the best place to mount the antenna will be the underside of the ATV cowling in the highest possible position.) 2. -
Page 22: Testing & Operation Of Remote
251206 SUPERWINCH X1, X2, X1F, X2F, EX1(WITH HAND HELD REMOTE) Testing/Operation 1. Reconnect the positive power lead from ON/OFF solenoid to battery. 2. Pull approximately 20 ft of cable off the winch by hand. Transmitter 3. Re-engage the winch clutch. 4. -
Page 23: Troubleshooting Guide
Trouble Shooting Guide Condition Possible Cause Correction Transmitter won’t operate Transmitter is off. Turn transmitter on (See Testing/Operation) . Low transmitter battery volt- Replace Battery. age. Transmitter temperature In extremely cold tempera- below 0°F (-18°C). tures, keep transmitter in a pocket of innermost layer of clothing when not in use. -
Page 24: Warranty Information
Warranty Information If the need should arise, warranty procedure is outlined on the back of your self-addressed, postage paid warranty card. Please read and fill out the enclosed warranty card and send it to Ramsey Winch Company. If you have any problems with your wireless remote, please follow instructions for prompt service on all warranty claims.