JVC RX-8010RBK Instructions Manual page 38

11.Press EFFECT to adjust the
overall level of the effect.
• Each time you press the button, the effect
level changes as follows:
EFFECT 1 EFFECT 2
EFFECT 5
As the number increases, DAP effect becomes stronger.
(Normally set it to "EFFECT 3.")
12.Press ROOM SIZE to adjust the
room size (sense of spaciousness).
• Each time you press the button, the room
size changes as follows:
ROOMSIZE 1 ROOMSIZE 2
ROOMSIZE 5
As the number increases, the interval between reflections
increases so that you will feel as if you were in a larger room.
(Normally set it to "ROOMSIZE 3.")
13.Press LIVENESS to adjust the
liveness.
• Each time you press the button, the
liveness changes as follows:
LIVENESS 1 LIVENESS 2
LIVENESS 5
As the number increases, the attenuation level of reflections over
time decreases so that acoustics change from "Dead" to "Live."
(Normally set it to "LIVENESS 3.")
On the front panel:
You can also use the buttons on the front panel to adjust the sound
with a Surround mode and a DAP mode. However, no test tone is
available when using the buttons on the front panel. So, make
adjustments while listening to the sound of the source played back.
1. Select and play a sound source.
• To enjoy Dolby Pro Logic, play back a software encoded with
Dolby Surround and labeled with
• To enjoy Dolby Digital, play back a software encoded with
Dolby Digital and labeled with
• To enjoy DTS Digital Surround, play back a software encoded
with DTS Digital Surround and labeled with
2. Press SURROUND ON/OFF to
activate an appropriate Surround
mode — PRO LOGIC, DOLBY
DIGITAL or DTS SURROUND.
The SURROUND ON/OFF lamp on the front panel button lights
up.
• Each time you press the button, the Surround mode turns on
and off alternately.
• When "PRO LOGIC" is selected, the PRO LOGIC indicator
lights up on the display.
35
EFFECT
2
MENU
EFFECT 3
EFFECT 4
ROOM
SIZE
3
ROOMSIZE 3
ROOMSIZE 4
LIVENESS
6
LIVENESS 3
LIVENESS 4
mark.
DOLBY SURROUND
mark.
D I G I T A L
mark.
SURROUND ON/OFF
3. Press DSP MODE repeatedly until
the DAP mode you want to adjust
— THEATER 1, THEATER 2,
HALL 1, HALL 2, LIVE CLUB,
DANCE CLUB, or PAVILION —
appears on the display.
The DSP MODE lamp on the front panel button lights up, and
the DSP indicator also lights up on the display.
4. Adjust the speaker output levels.
1) Press LEVEL ADJUST repeatedly
until one of the following indications
appears on the display.
"CENTER":
To adjust the center speaker level.
"REAR L":
To adjust the left rear speaker level.
"REAR R":
To adjust the right rear speaker level.
2) Press CONTROL UP 5/DOWN ∞ to
adjust the selected speaker output level
(from –10 dB to +10 dB).
3) Repeat 1) and 2) to adjust the other
speaker output levels.
5. Adjust the center tone.
1) Press EFFECT repeatedly until "CTR
TONE" appears on the display.
The display shows the current setting.
2) Press CONTROL UP 5/DOWN ∞
to select the center tone level you
want.
• Each time you press the button, the
display changes to show the following:
CTR TONE 2
CTR TONE 1
(Softer)
CTR TONE 5
(Sharper)
To make the dialogue softer, select "CTR TONE 1" or
"CTR TONE 2."
To make the dialogue clearer, select "CTR TONE 4" or
"CTR TONE 5."
When "CTR TONE 3" is selected, no adjustment is applied.
6. Adjust the overall levels of the effect.
1) Press EFFECT repeatedly until
"EFFECT" appears on the display.
The display shows the current setting.
2) Press CONTROL UP 5/DOWN ∞
to select the effect level you want.
• Each time you press the button, the
display changes to show the following:
EFFECT 1 EFFECT 2
EFFECT 5
As the number increases, DAP effect becomes stronger.
(Normally set it to "EFFECT 3.")
DSP MODE
AL LEVEL
ADJUST
CONTROL
DOWN UP
EFFECT SETTIN
CONTROL
DOWN UP
CTR TONE 3
(Soft) (Flat)
CTR TONE 4
(Sharp)
EFFECT SETT
CONTROL
DOWN UP
EFFECT 3
EFFECT 4