Table of Contents
Advertisement
From the remote control:
1. Press SOUND CONTROL.
The 10 keys are activated for sound adjustments.
2. Press SURROUND repeatedly
until the DAP mode — LIVE
CLUB, DANCE CLUB, HALL, or
PAVILION — appears on the
display.
The DSP and the selected DAP mode indicators also light up on
the display.
3. Press REAR•L – / + to adjust the
rear speaker output level.
• Pressing REAR•L – decreases the output
level up to –10 dB.
• Pressing REAR•L + increases the output
level up to +10 dB.
Note:
You cannot adjust the left and right rear speaker output levels
separately.
4. Press EFFECT to select an effect
level you want.
• Each time you press the button, the effect
level changes as follows:
DSP EFFECT 1
DSP EFFECT 2
DSP EFFECT 5
As the number increases, the selected DAP mode becomes
stronger.
Adjusting the Surround Modes — Dolby
Surround and JVC Theater Surround
Before you start, remember...
• Make sure that you have set the speaker information correctly
(see page 11).
• There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
• You can only adjust the effect level when selecting JVC Theater
Surround.
• You can only adjust the rear and/or center speaker output levels
when you have connected rear speakers and/or a center speaker
and have set "REAR SPK" and/or "CENTER SPK" correctly. See
page 11.
From the remote control:
1. Press SOUND CONTROL.
The 10 keys are activated for sound adjustments.
2. Press SURROUND repeatedly
until the mode — "PRO LOGIC"
or "THEATER" — appears on the
display.
• When selecting "PRO LOGIC," the PRO LOGIC indicator
also lights up on the display.
• When selecting "THEATER," the DSP, PRO LOGIC and
THEATER indicators also light up on the display.
SOUND
CONTROL
SURROUND
3
– REAR•L +
8
9
EFFECT
4
DSP EFFECT 3
DSP EFFECT 4
SOUND
CONTROL
SURROUND
3
3. Press TEST to check the speaker
output balance.
"TEST TONE L" starts flashing on the
display, and a test tone comes out of the
speakers in the following order:
TEST TONE L
(Left front speaker)
TEST TONE S
(Rear speakers)
Notes:
• You can adjust the speaker output levels without outputting the
test tone.
• The speaker indicators also light on the display while the test
tone comes out of the speakers.
L: Lights when the test tone comes out of the
left front speaker.
L
C
R
C: Lights when the test tone comes out of the
center speaker.
S
R: Lights when the test tone comes out of the
right front speaker.
S: Lights when the test tone comes out of the
rear speakers.
4. Press CENTER – / + repeatedly to
adjust the center speaker output
level (from –10 to +10).
5. Press REAR•L – / + to adjust the
rear speaker output level (from
–10 to +10).
Notes:
• You cannot adjust the left and right rear speaker output levels
separately.
• You cannot use the REAR•R –/+ buttons to adjust the rear
speaker output levels.
6. Press TEST again to stop the test
tone.
7. ONLY FOR "THEATER":
Press EFFECT to select an effect
level you want.
• Each time you press the button, the effect
level changes as follows:
DSP EFFECT 1
DSP EFFECT 2
DSP EFFECT 5
As the number increases, JVC Theater Surround becomes
stronger.
TEST
2
TEST TONE C
(Center speaker)
TEST TONE R
(Right front speaker)
– CENTER +
5
6
– REAR•L +
8
9
TEST
2
EFFECT
4
DSP EFFECT 3
DSP EFFECT 4
20
Hide quick links:
Advertisement
Table of Contents
