Pioneer VSX-45TX Service Manual page 151

5
5 SYSTEM SET UP button
Use for all system setups, including the speaker and
sound systems. For more information see. "Setting up for
Surround Sound" starting on page 36. For a DVD player
use this button to bring up the DVD menu and for a tuner
use this button in the same way as the TUNER EDIT
button.
6 5˜∞˜2˜3˜ENTER buttons
These buttons can be used for a variety of operations in
the SYSTEM SETUP menu.
These buttons are used to control the menus for other
components when in those modes (DVD, digital TV
tuner, satellite tuner, cable tuner, etc.). In TUNER mode,
they can select a station and/or a frequency.
7 AUDIO button
Use to switch the audio tracks of a DVD when in DVD
mode.
8 Command button for other components
Use these buttons to control other components you
selected with the MULTI CONTROL buttons. You must
input the preset code in order use this function.
9 TV CONTROL buttons
The following buttons are used to control the TV only and
can be used once they are preset to control your TV.
TV INPUT: Press to select the input source for the TV.
TV CH +/– : Use these buttons to change the channel of
the TV.
TV VOL +/– : Press to control the volume of the TV.
0 Listening mode buttons
SURROUND buttons (MOVIE, MUSIC, | \ & ENTER):
MOVIE: Press to put the receiver into MOVIE listening
mode.
MUSIC: Press to put the receiver into MUSIC listening
mode.
| \: Use to select the MOVIE or MUSIC listening
mode.
ENTER: Use this button to enter information concerning
the listening modes.
STEREO/DIRECT: Switches the receiver into STEREO
mode if it was in a different sound mode or toggles
between DIRECT and STEREO mode.
DIRECT playback bypasses the tone controls and
channel level for the most accurate reproduction of a
program source.
- SB CH MODE button
Use this button to turn the surround back channels
on/off/auto or switch the virtual surround back mode
between on/off/auto.
= SYSTEM OFF button
This button turns off components in two ways. First,
when pressed it will turn off all PIONEER components.
Secondly, any component that has programmed into the
SYSTEM OFF settings will be turned off.
For example: If you programmed power off in the
SYSTEM OFF settings for your TV and VCR, pressing
the SYSTEM OFF button will turn off these components
even if they are not PIONEER products.
5
6
~
RECEIVER (standby/on) button
Press to turn power of the receiver on or to standby (off).
! MULTI OPERATION button
Use this button to start the MULTI OPERATION mode.
For how to program and use the MULTI OPERATION
mode.
@ RECEIVER button
Use this button to switch the remote control into receiver
mode in order to get certain receiver functions or do
receiver setups.
# TOP MENU/GUIDE button
Use to find stations or menus on a digital TV tuner. For a
DVD player use this button to bring up the DVD menu.
$ RETURN button
When you are in a receiver setup operation this button
will go back one step in the SYSTEM SETUP procedure.
When you are using your DVD menu screen this button
acts the same as the DVD player's "Return" button.
When you are using cable tuners, satellite tuners or
digital TV tuners this button will either exit you from the
menu screen or act like a "Return" button above,
depending on the maker of the unit.
% INPUT button
Press to select an input source. The button will cycle
through all the possible sources.
^ VOLUME (+/–) buttons
Use to raise or lower the volume of the receiver.
& MIDNIGHT button
Switches the MIDNIGHT listening mode on or off (for all
modes except THX CINEMA and MULTI CH IN).
* MUTE button
Press to mute or restore the volume.
( MULTI CH INPUT button
Use this button to select the component you have
hooked up to the MULTI CH IN terminals (for example, a
DVD-Audio player).
) ACOUSTIC EQ button
Press to switch on/off and select the type of acoustic
calibration EQ.
_ REMOTE SETUP button
Use to customize the remote control functions and the
remote control itself.
VSX-45TX
6
7
7
8
A
B
C
D
E
F
151
8