Sony RDR-GX210 Service Manual page 10

QQ
3 7 63 1515 0
Step 4: Connecting the Audio Cords
Select one of the following patterns A or B, according to the input jack on your TV monitor, projector,
or AV amplifier (receiver).
This will enable you to listen to sound.
(white)
LINE 2 OUT
L
AUDIO
(red)
R
VIDEO
to LINE 2 OUT (AUDIO L/R)
AERIAL LINE 3 / DECODER DIGITAL OUT COMPONENT LINE 2 OUT LINE 4 IN
VIDEO OUT
COAXIAL
IN
PCM/DTS/
MPEG/
L L
DOLBY DIGITAL P /C
B B AUDIO AUDIO
VIDEO OUT LINE 2 OUT
LINE 1 - TV SELECT
RGB
P R /C R R R
OUT
COMPO-
Y VIDEO VIDEO
NENT S VIDEO
to DIGITAL OUT
(COAXIAL)
DIGITAL OUT
COAXIAL
PCM/DTS/
MPEG/
DOLBY DIGITAL
Coaxial digital cord
(not supplied)
to coaxial
[Speakers]
digital input
Rear (L)
Front (L)
AV amplifier (receiver)
with a decoder
Centre
: Signal flow
z Hint
For correct speaker location, see the operating instructions supplied with the connected components.
Note
TE
L 13942296513
Do not connect your TV's audio output jacks to the LINE IN (AUDIO L/R) jacks at the same time. This will cause
unwanted noise to come from your TV's speakers.
16
Step 5: Connecting the
Mains Lead
Plug the recorder and TV mains leads (power
cords) into the mains. After you connect the mains
lead, you must wait for a short while before
operating the recorder. You can operate the
recorder once the front panel display lights up and
the recorder enters standby mode.
If you connect additional equipment to this
recorder (page 23), be sure to connect the mains
lead after all connections are complete.
to mains
www
.
18
http://www.xiaoyu163.com
A
INPUT
VIDEO
Audio cord
(supplied) (white)
L
AUDIO
(red)
R
TV, projector, or AV
amplifier (receiver)
DVD recorder
DIGITAL OUT
PCM/DTS/MPEG/
DOLBY DIGITAL
OPTICAL
DIGITAL OUT
to DIGITAL
PCM/DTS/MPEG/
OUT
DOLBY DIGITAL
(OPTICAL)
OPTICAL
Optical digital cord
(not supplied)
or
B
to optical
[Speakers]
digital input
Rear (R)
Front (R)
Subwoofer
Step 6: Preparing the
Remote
You can control the recorder using the supplied
remote. Insert two R6 (size AA) batteries by
matching the 3 and # ends on the batteries to the
markings inside the battery compartment. When
using the remote, point it at the remote sensor
on the recorder.
Notes
• If the supplied remote interferes your other Sony DVD
recorder or player, change the command mode number
for this recorder (page 20).
• Use the batteries correctly to avoid possible leakage
and corrosion. Do not touch the liquid with bare hands
should leakage occur. Observe the following:
– Do not use a new battery with an old battery, or
batteries of different manufacturers.
– Do not attempt to recharge the batteries.
– If you do not intend to use the remote for an extended
period of time, remove the batteries.
– If battery leakage occurs, wipe out any liquid inside
the battery compartment, and insert new batteries.
• Do not expose the remote sensor (marked on the
front panel) to strong light, such as direct sunlight or
lighting apparatus. The recorder may not respond to the
remote.
x ao
y
i
http://www.xiaoyu163.com
8
A
Connecting to audio L/R input
jacks
This connection will use your TV's or stereo
amplifier's (receiver's) two speakers for sound.
Connect using the audio cord (supplied).
White
(L)
Red
(R)
• Surround effect (page 49)
or
Note
Do not connect the LINE 4 IN (AUDIO L/R) and LINE
2 OUT (AUDIO L/R) jacks to your TV's audio output
jacks at the same time. This will cause unwanted noise to
come from your TV's speakers.
Q Q
3 6 7 1 3
Controlling TVs with the remote
You can adjust the remote's signal to control your
TV.
If you connected the recorder to an AV amplifier
(receiver), you can use the supplied remote to
control the AV amplifier's (receiver's) volume.
Notes
• Depending on the connected unit, you may not be able
to control your TV or AV amplifier (receiver) with
some or all of the buttons below.
• If you enter a new code number, the code number
previously entered will be erased.
• When you replace the batteries of the remote, the code
number may be reset to the default setting. Set the
appropriate code number again.
TV/DVD
switch
"/1
1 2 3
PROG +/–
4 5 6
Number buttons,
7 8 9 2 +/–
-/--
0
t, TV/DVD
1
Slide the TV/DVD switch to TV.
2
Hold down [/1.
3
Enter your TV's manufacturer code (see
"Code numbers of controllable TVs"
below) using the number buttons.
4
Release [/1.
When the TV/DVD switch is set to TV, the
remote performs the following:
[/1
Turns your TV on or off
2 (volume) +/–
Adjusts the volume of your
u163
TV
PROG +/– Selects the programme
position on your TV
.
(wide mode) Switches to or from the
wide mode of a Sony wide-
screen TV
t
(TV/video) Switches your TV's input
source
1-4
2 9 9 4 2 8
B
Connecting to a digital audio
input jack
If your AV amplifier (receiver) has a Dolby*
2
Digital, DTS* , or MPEG audio decoder and a
digital input jack, use this connection.
Connect using a coaxial or optical digital cord (not
White supplied).
(L)
Coaxial cord
Red
(R)
Optical cord
• Surround effect
Dolby Digital (5.1ch), DTS (5.1ch), MPEG audio
(5.1ch)
*1
Manufactured under license from Dolby Laboratories.
"Dolby," "Pro Logic," and the double-D symbol are
trademarks of Dolby Laboratories.
*2
"DTS" and "DTS Digital Out" are registered
trademarks of Digital Theater Systems, Inc.
Notes
• After you have completed connection B, make the
appropriate settings under [Audio] Setup (page 74). If
your AV amplifier (receiver) has an MPEG audio
decoder function, set [MPEG] to [Bitstream] in
[Audio] Setup (page 75). Otherwise, no sound or a loud
noise will come from your speakers.
• The surround sound effects of this recorder cannot be
used with connection B.
1 5 0 5 8 2 9 9 4
Number buttons and Selects the programme
-/--* position on your TV
* If you use the number buttons to select the TV's
programme position, press -/-- followed by the number
buttons for two-digit numbers.
To operate the TV/DVD button
(for SCART connections only)
The TV/DVD button switches between the
recorder and the last input source selected on the
TV. Point your remote at the recorder when using
this button. The button works even if the TV/DVD
switch is set to DVD.
When you connect the recorder to the TV via the
SCART jacks, the input source for the TV is set to
the recorder automatically when you turn the
power on. To watch another source, press the TV/
DVD button to switch the TV's input source.
Code numbers of controllable TVs
If more than one code number is listed, try
entering them one at a time until you find the one
that works with your TV.
Manufacturer Code number
Sony 01 (default)
Aiwa 01 (default)
Grundig 11
Hitachi 23, 24, 72
Loewe 06, 45
Nokia 15, 16, 69, 73
Panasonic 17, 49
Philips 06, 07, 08, 23, 45, 72
Saba 12, 13, 36, 43, 74, 75
m
Samsung 06, 22, 23, 71, 72
Sanyo 25
co
Sharp 29
Telefunken 12, 13, 36, 43, 74, 75
Thomson 12, 13, 43, 74, 75
Toshiba 38
LG 06
JVC 33
9 9
1
2 8 9 9
17
, continued
19